Check engine light on, car stalled once. Pulling code p0320 "Engine Speed Input Circuit Malfunction." Tachometer works intermittently. Where do I start?
View 2 RepliesRecently got check engine light fault code p0320
2005 3.5 with 172k miles
I have a 2003 Santa Fe, V4, 2.4L.
So the other day, my CEL and I got it scanned: p0320, or "Ignition/Distributor Engine Speed Input Circuit Malfunction."
It was accompanied with two symptoms:
1. The car will sometimes sputter on startup, and the tachometer will be zeroed out. I have to turn the car off and turn it back on, and it will start normally, albeit with a bit of a misfire on idle.
2. The car will sometimes die while at a stop. Just like the first symptom, if I turn the car off and turn it back on, it will work normally.
I looked on here, and it seemed like everyone solved a p0320 by replacing the Ignition Failure Sensor. So that's exactly what I did. But nothing changed; I still have the symptoms, and the CEL came back on and is still reading p0320.
What should be my next step? Could it be faulty wires that give power to the Ignition Failure Sensor?
2004 2.4L Hyundai Santa Fe here, died whilst travelling, lost all power and then wouldn't start. Sounds like its trying to turn over.
The fuel cut off seems to have been activated as it clicked when I pushed it but the car still wont start.
I do not have any engine management lights but when connecting the code reader I got P0320, however the code was stored but not present... and still the car will not start. I cleared the code and the code didn't re appear but the car will still not start.
As the code isn't immediately present does this mean the sensor is at fault or do I have other problems?
My check engine light came on the other day and the code stated the the "throttle position is open" so after researching and everyone telling me that i need to change the sensor. I did everything after was fine running better but today only after 3 days replacing it i get the same problems. car has no get up and go hardly can push to 20 mph and when in idle i press the break it starts to bog down and almost want to shut off! and can be really loud...
Santa fe 05' 3.5L ....
At roughly 140,000 miles, my wife's '07 Santa Fe GLS has thrown a P0456 code. Does this code on a Santa Fe common?
It is "evaporative emission system leak detected (very small leak)." The good news, I guess, is that it is 'very small.' However, being small may make it more difficult to detect.
I've recently bought used Hyundai SantaFe 2007 and the engine check light lit up. I've bought EML327 OBD2 scanner, it showed P1405 meaning "EGR tempereature sensor incorrect". Some of my friends says it has something to do with CPF filter and EGR valve. They think, i should clean both CPF and EGR. Car service told me that DPF (not CPF) filter cleaning costs arround 350eu and one service told me to simply take it out and reprogram car computer. As far as EGR valve cleaning goes, no service wants to do this. I don't really know much about cars, so my main question is what would be my next step in trying to fix this error.
View 3 RepliesMy 2010 Santa Fe is only 2 month old and has 2000km now the check engine light is on. Went to the dealer and found out the code is P200A -Intake manifold runner performance. And they just clear the code. What does this code mean?
View 22 RepliesI have a 01 SF 2.4 4cyl. I just returned from a road trip in which my engine light came on. The codes read for mixture too rich and bad MAF sensor. I took it into the shop and has a new MAF sensor installed, full tune up and oil change. I picked it up yesterday. After just 16 miles the engine light came on again, this time reading mixture too lean. Now, at 35 miles since servicing, while trying to drive home, it would rev up and down, then completely stalled, and now it will start, but not stay running. It made a 4000 mile trip even with a bad MAF and rich codes, but now can't even make it 40 miles.
View 6 RepliesHave 2 problems that are giving me major problems.....especially with 100 degree heat in Dallas.
1. Ac stopped blowing cold last night out of blue. Still blows just not cold. Replaced bad fuse and drove for 5 minutes. Blew again. Checked out the control/ circuit board but looks ok. Really cant afford dealer.
2. Check engine light problem for months. Gas gauge wasn't working. Replaced fuel sending units and it fixed that but still light. Code says p441. Dealer said need solenoid valve. Replaced both the solenoid valve and the purge control valve. Still check engine light.
I own the 2014 Santa fe turbo 2.0 litre limited which has 4000 km on it. Within 210 km the engine light came on 3 times. I took it into the shop and they ran a code of P0303 which is a misfire, they changed the coils #2 and #3 and cleared the code. The second time it showed the same code but the shop said it was in the history so that is why the same code came up again. They ran an update ECM? and all was good. Now the 3rd time they tell me no code has come up and can't do anything about the engine (they cleared it) but it was like chasing ghosts. My vehicle runs great so not sure why I am constantly having this issue.
View 68 RepliesMy '04 santa fe 3.5 v6 gls/lx, 79k miles, gas, auto, check light has just come on while I was driving a less than 10 mile journey. How can I check what is wrong. Do I need some sort of diagnostic code checker. Do any national outlets check it for free (Pep Boys or Auto Zone, etc).
Just 5 days ago (about 50 miles only) I had timing belt, water pump, plugs and leads replaced, brakes checked and lubes flushed; BUT not at above dealers. I would rather know what the code is saying before I go back to the shop who carried out the work.
How can i turn off check engine light (hyundai santa fe 2003 3.5) by fuse ? I do not have any code scanner.
View 10 RepliesI recently purchased a 3.5 V6 Santa fe. The Check engine light keeps going on. I took it to a few shops and I am getting the same code. It is the O2 sensor in bank one. (I think the the code was po170.) The light keeps going on and off. All I can find are the same problems with different Santa Fe engines (2.7, etc. )... My SUV has 100,050 miles on it.
View 1 Replies2004 2.4L Sante Fe Base model. Car stalled out the other night, engine cranks but wont turn over. I have it towed to mechanic who tells me that the ECU is fried and they cant get any diagnostic done, that only a hyundai service can do this. I have it towed to service. Service tells me that they cant get a diagnostic done without a working ECU and that for the ECU alone. Then they could figure out what was going on with the car. The service also told me that the ECU isn't something that you can just go get at a scrapyard because it is specific to the VIN on my car. It just didn't sound right to me but I might be wrong.
View 7 RepliesI have a 2004 Santa Fe (4 cyl 2.7 L FWD) with only 42,000 miles on it. Coming home from work I was stopped at a stop sign and after stepping on the gas (halfway thru the intersection) my engine stalled - coasting to a stop (while crossing a very busy intersection I might add). After putting it in park I try to restart it - the engine cranks over as usual and starts but roughly 4 to 7 seconds afterwards it stalls again. I did this 4 or 5 times again with the same results. I'm almost positive the check engine light is on. The next day I popped the hood to see if the belt broke but its fine so I tried to start it again (same results engine starts but after 4 to 7 sec. stalls again). Before this engine trouble I haven't had one ounce of trouble from my Santa Fe. Not to be funny but yes there is a half a tank of gas in it... with plenty of fluids in it. After some research I kind of think its the Crank-shaft sensor (seems to be a problem with them in the Santa Fe's).
View 14 RepliesI have had a check engine light go on and off with P0700 and P0741 but since the flush day 3 it hasnt come back on and it was chucking with rpm doing small jumps... but now it does it in the mornings after sitting all night after a few chucks its fine for the rest of the day til the next day no check engine light so far, but transmission flush has worked a lot not as bad as before the flush.. So what else could be causing it? Its a 2006 hyundai santa fe with 274,000 kms.
View 24 RepliesI have A 2001 Santa Fe. The check engine light came on about 3 weeks ago and the car was still running fine up until the last few days it felt a little sluggish. Today I got a little muffled backfire noise. It was like a putting noise if I pushed on the gas to hard to speed up. The car has 95,000 miles on it.The car starts up with no problems and doesn't stall. Its A 6 cylinder All wheel drive vehicle.
View 10 RepliesI have a 2002 SF GLS/LX (?) with 2.7 L V6 2WD (60,000 miles) and it started to apply the ABS brakes in a random manner. Found out it was caused by a broken front wheel tone ring. So, I pulled the ABS fuse under the dash and it stopped the brake problem. Drove it today to pick up some wood and now the check engine light has come on.
My neighbor has an OBD scanner and he plugged it in and said I have a P0501 code and a P1529 code, but he didn't know what they meant. What they mean and are they related to me pulling the fuse under the dash? Did I pull the wrong fuse? Is there another fuse somewhere that I should have pulled?
My 2002 Hyundai Santa Fe 2.7L V6 AWD failed to start a week ago. After towing to my neighborhood repair shop, it was diagnosed as a faulty ECM based on code P560 (System Voltage Problem). They replaced the ECM (along with relay) with a used one with the exact same part#. After that, the car was started and run OK but Check Engine Light stays on all the time. The codes displayed are:
P1529 TCU MIL Request Signal
P0501 VSS Range Performance
I was told that this is caused by the fact that each ECM is VIN/PIN locked. The replacing ECM was used in another car before and was locked with a different VIN thus cannot communicate with some components of the current car.
My questions are:
Can this used ECM be unlocked and relocked with a new VIN/PIN? If so, does it require the previous VIN/PIN to unlock? Most likely the previous VIN/PIN is no longer available.
Does this service require the presence of the car or can it be done with the ECM alone? Do keys need to be re-registered? The car starts fine currently.
I just recently purchased a 2001 Prius with 92,000 miles on it and the check engine like comes on frequently. I have a scangauge and I scan for codes and it comes up P0000. I clear the codes the light goes off and everything seems to be ok. I'm not even sure where to start "looking" for something to be wrong.
View 17 Replies