Silverado :: 1999 Chevy Shifting Really Hard In First And Second / Revs Up To About 2000 RPMs


May 8, 2010

My truck was intermittently shifting really hard in first and second . I drained the tranny fluid and installed a new filter and replaced the fluid, I also changed plugs and wires. Tranny fluid is at the top of the hash marks on dipstick when hot and in park. When I come to a complete stop my engine 5.3 litre v8 revs up to about 2000 rpms but the truck takes off slowly like the tranny is slipping it is worse on an incline. If I dont come to a complete stop it shifts fine and takes off with good power. After it shifts to second it shifts normally and drives fine. tranny fluid looks clean and does not smell burnt. Also when driving on the highway if I am going 45 mph and punch the gas it wont rev past 2200 rpms like it is lugging down. when i shift thru gears manually there is no slippage what so ever and when in park engine revs to 6000 rpms no problem. Also tranny is a 4l60e

View 14 Replies

Advertisement

Chevy - Silverado :: 1999 - Hard Shifting / Clunk After Long Drives

I have a 1999 chevy silverado 5.3 4wd w/ tow package. I bough it with 30,000 mi. It has always had a hard shifting/clunk after long drives or sometimes short ones that involve a lot of elevation. Oddly, if I stop and shut the car off for a minute or two the hard shifting stops, but eventually starts again. The truck now has 160,000...still with the shifting issue. What is this and with this many miles is it serious?

View 4 Replies

Silverado :: 2006 Chevy Truck Hard Shifting Manual Transmission

2006 chevy 4.3 v6 5 speed manual trans. Very hard to shift into and out of gear , the truck has about 80,000 miles on it , its had the new trans fluid gm replaced for smoother shifting. If you hold the clutch pedal down on the floor hard it works fine. It all most like the pedal it screwed up. The pedal ass is plastic junk, I am thinking the pedal is bended. The clutch does not slip and I tried bleeding the clutch master cylinder and there are no leaks anywhere !

View 9 Replies

Chevrolet - Silverado :: 2000 - Hard Shifting Between 1 - 2 - 3 Intermittently

When parked and you shift between P to D or R loud engagement of transmission. Thought it was u joints, buddy says both look good/sound good when engaging P D R. Also shifts hard between 1-2-3 intermittently. I did read that it could be the TCC regulator valve?

View 2 Replies

Silverado :: 1993 Chevy 2WD - When Accelerating RPMs Go Way Up And Won't Shift

I have a 1993 Chevy Silverado, 350, 2WD. It has a 4L60E transmission. I just started having a problem shifting from 1st to 2nd. When accelerating the RPM's go way up and won't shift until I let off the throttle. Then it shifts into all other gears normally.

If I accelerate slowly. it will shift into 2nd at about 16 MPH. It will then shift into all other gears normally. I have replaced the Throttle Position Sensor, flushed the transmission and replaced the filter and fluid. This made know change in performance.

I am now suspecting that it might be the 1-2 shift solenoid. The check engine light is not on and everything else works fine.

View 1 Replies

Silverado :: 96 Chevy - Misfires / High RPMs And Doesn't Go In Overdrive

I have a 96 chevy Silverado 4x4 5.7 motor and it does the same thing but it doesn't leave in first gear, it misfires and high rpms and doesn't go in overdrive. but if I drive a little while and turn it off, it's fine it acts like a normal truck would. then if my truck is off for more that a couple of hours it goes back to it acting up.

View 1 Replies

Silverado :: 2001 Chevy - Transmission Will Wind Out In 1st Gear And Not Shifting

I have a 2001 Chevy half ton 4wd. It has the 5.3L, 4L60E transmission, and a 246 transfer. I am having problems with shifting. if I out the truck in drive, the trans will wind out in 1st gear and not shift. I then pull it down to 2nd and it will shift. When it comes time for third gear, it will not shift at all. It just simply revs until it catches up with the speed at which the truck is rolling. I thought it was a bad tranny as I smoked one and replaced it with a used one so we rebuilt the tranny and it still does the exact same thing. Also the speedo is not working but the odometer is on. Don't know if its registering anything but its on. I have also checked every single fuse and maxi fuse in the engine compartment and the drivers side panel.

View 1 Replies

Silverado :: 1992 Chevy 1500 Runs And Starts Great But Won't Do High RPMs

I have a 92 chevy pick up 5.7 with 159,000 miles. The truck runs and starts great but shortly after I bought it 3 years ago it developed a sort of misfire at higher rpm's, it's fine if I drive it normally but if I try to pass someone it will downshift then fall on it's face, (spit,sputter and slow down). some times I can feather the accelerator and it will come back again. I normally don't drive the truck in the winter but this week I was forced to use it and the cold weather is seriously affecting it, it took forever to get it up to 70 mph after getting on the highway. once up to speed it will do 75 all day without an issue.

I've replaced the plugs, wires, pulled the throttle body and cleaned it as the port for the pcv valve was plugged solid with carbon. I have not replaced the cap and rotor as they seemed to look fine. I have not checked the fuel pressure because it will break the tires loose upon take off and I don't think that would be possible if the pressure was low, would it?

View 5 Replies

Silverado :: 2000 Chevy Truck Won't Start - Security Light On

I have a 2000 Chevy silverado. I recently was having problems with the transmittion not switching correctly. Long story short the shop told me to fix the problem I had to put in

A new transmition as well as a new computer which I did, from another Chevy. It worked for a few days then The truck was not starting and had security light on. Had alarm specialist take look and he said the computer had to be reprogrammed. It was reprogrammed at merles. And was still not working. Its unable to start, starts at random once in a long while. ignition switch was changed and still gave same problem. Took to another shop they had a specialist take a look and he said the computer had to be reprogrammed again.

Also would it be possible to bypass the anti theft system by adding a remote start, or cutting some wires. I just really need to get this truck running.

View 14 Replies

Silverado :: 2001 2500HD 6.0 - Shifting Really Hard Into All Gears

I have been trying to self diagnose an issue with my pick up for a while now. I have an 01 Silverado 2500HD 6.0 that shifts really hard into all gears. I was told it was the transmission going out, so we replaced the transmission with a rebuilt one and it did nothing for the shifting issues. We then had the transfer case rebuilt which also did nothing for our problems. My father who has some general mechanic knowledge is certain that the free floating rear end is not turning with the correct timing for the transmission shifting. No check engine lights come on at all during these issues. When I took it to a mechanic he told me I needed a new transmission and blew me off when I told him it was just replaced.

View 3 Replies

Chevy - Silverado :: 1999 - Shakes Badly At Several Speeds

I have a '99 Silverado 1500 with a 4.3L V-6 amd 188,000. It picked up a problem recently that's been stumping me. Occassionally, and for no reason I can sort out, it starts to shimmy badly. This behavior has come about at several speeds. Sometimes just cruising down the road at 35-45 it starts to shimmy and wobble and the steering wheel shakes as if a wheel is horribly out of balance. Other times this occurs at highway speeds - it's noticeable and alarming. The problem can last a long while; othertimes the symptoms disappear in a few seconds. The first time it happened I thought I had a flat or was about to lose a wheel - this is not a subtle problem.

I've checked several things and came up empty. No delamination in the tires and nothing out of round, but just to be sure I had the wheels balanced and rotated - the balance was spot on when checked. Alignment is good. Did those things, but the symptoms continued. The vehicle is high mileage so I put in on the lift and checked the front-end. The steering rack has a very slight amount of play and the hub bearings have a very small amount of play too - I'll get after those, but they're not causing this intermittent problem. Everything else is tight. Shocks are fine, brakes are fine, I checked the rear-end as well - everything is straight and true. Air pressure is set correctly. I checked the driveshaft for runout and play - that's not the problem. The truck has never been in an accident and nothing seems misaligned.

The truck drives like a new truck most of the time, then suddenly, on a smooth road, it starts wobbling around. I'm starting to believe the problem might lie under the hood. I had a problem some time back with misfiring and the truck bucking - this turned out to be a worn distributor. A new distributor, rotor and wiring solved that problem. But these symptoms are not similar - this is not a bucking problem; the entire vehicle starts to shimmy and wobble with the steering wheel vibrating back and forth. It's hard to tell, but I cannot detect any misfiring or rough running in the engine when these symptoms appear and I have no 'check engine' warnings.

Are there any engine/transmission/drivetrain related issues that could cause intermittent symptoms that feel like an out of balance condition? A few other facts:- I have noticed the truck is a little down on power lately- The fuel economy has dropped off - I used to do around 20, now I'm down to 16mph highway- (Very) slightly rough idle

View 5 Replies

Silverado :: 1997 - CEL Code P1860 / Shifting Firmly Into Second And At 65mph Gives A Hard Jerk

1997 Chevrolet Silverado 4x4 z71 transmission problems. 5 months ago I had it serviced and A/B shift solenoids changed along with filter and fluid. Now check engine is back on with P1860 code truck also has started shifting more firmly into second and at 65mph it gives a hard jerk.

View 8 Replies

Chevy - Silverado :: 1999 - Getting Code PO405 / PO404 EGR Sensor Low Cut?

Ok here is my problem i have a 99 Chevy Silverado LS 1500 5.3L. and i am having problems with egr codes coming up. I have been getting the P0405 EGR Sensor low circuit, i was told that my EGR was bad so i replaced it. ran fine for around 1-2 months and than the code came back on, talked with the guys where i bought it and they said that it could of been a faulty EGR so they replaced it. K so thats 2. 1-2 months down the road again same thing code pops up, talked with them replaced it again, number 3 so it did it again this time when i talked to them again they talked me in on getting the one better than the one i was using before and to buy a gasket with a screen. so thats #4. now today the code pops up again. This time codes P0405 came up and also P0404. oh and i should mention that i replaced the wiring plug also.

View 12 Replies

Silverado :: 1999 Chevy - Rubbing Sound Coming From Steering Column When Turning

I have a rubbing sound that seems to be coming from the steering column when turning. Don't hear it outside of cab just in the inside.

View 4 Replies

Golf IV / Jetta IV :: Hard Shifting From 1st To 2nd Gear Depending On RPMs

Car in question is my 2003 Jetta 1.8t with the 09A 5 Speed Automatic. For the past 2 or 3 months these have been the symptoms: 1st to 2nd gear, very hard shift depending on RPM's (Higher the RPM's the harder the shift) 2nd to 3rd gear, not really hard but it kinda 'flares' the gearbut still shifts. All other gears are fine, although if you accelerate hard out of 4th it will have a little bit of a hard shift. I'm thinking either solenoids, or the speed sensor?

View 1 Replies

Impala - Chevrolet :: 2000 Chevy Whistle When Accelerate / Shift Hard

Why does my 2000 chevy impala whistle when i accelerate? it also seems to shift hard.

View 10 Replies

Accent LC (2000-05) :: Gear Shifting - RPMs Instantly Jumps Up

I have a 2005 Hyndai Accent GT automatic (83,000 km) and I am having a problem with the gear shifting. It's happening more and more.

As I am driving I am pretty sure that it's changing to a higher gear but when I slow down it seems like its not shifting down at all. Coming off the Highway I have to slow down and when I speed back up it seems like its still in the high gear. The RPM's instantly jumps up.

The only way it fixes it self is when I pull over and shut off the car and then start it up again and I am fine. A friend at work said that I may have to have my transmission fluid checked and filled up.

View 7 Replies

Silverado :: 98 5.7 Chevy Truck Not Starting

I have a 98 chevy truck that won't start. After it sits. It was starting after cycling the key a few times. But now it won't start. Could it be the pump? I hear it running.

Or could it be the regulator? It was running good after it started. No check engine light, no gas smell, and no rough idle.

View 6 Replies

Alero :: 2000 4cyl Shifting Hard?

i just started having a problem with my car. I drove it somewhere and my trac off light was on i noticed it was running a little rough but i wasnt to concerned. When i got back in the car to drive it home it shifting very rough like it was throwing the car car forward when it shifted. Also when i stop it almost stalls out when i hit the gas. I have to press the gas a couple times to gwt it to where it wont stall.

Also forgot to say when starting and sitting idle no matter if it is hot or cold it runs really rough.

View 2 Replies

Accent LC (2000-05) :: Hard Shifting Between Gears And Wouldn't Go Over 45

That said my wife bought a 2001 Accent 1.6L Auto while I was overseas and it's been a great car, about 8 days ago it just crapped out. The reverse went out on her so we took it to get the codes read and on the way it went in limp mode, started hard shifting between gears and wouldn't go over 45 she says. Took it in to the stealership today and they said that the trans is shot as well as showing codes for P1527, P0732, and P0734. I know what the two slippage codes are and I can prolly just replace the speed sensors and that will be fixed but I'm not sure about the reverse and P1527.

View 4 Replies

Chevy - C10I :: Engine Revs Kind Of High Before Transmission Engages

1983 chevy c10I bought this old truck about a week ago and I noticed a few things right from the start. Engine revs kind of high before the transmission engages (about 1,200+ rpms).at highway speed the truck shakes and vibrates really bad at times. the steering wheel doesn't vibrate so I dont think it`s ball joints or tie rods.The truck barely goes backwards when in reverse, the engine revs high (over 2000 rpm) but the truck barely moves backwards.It almost feels like the emergency brake is on.

yesterday the truck (transmission?) started slipping and then it stopped working. I was stopped on the side of the road and this old guy stopped.I told him what happened and he said it was probably the transmission but he knew a way to get it working again long enough to get me home. He picked up a handful of sand from the side of the road and put it in the transmission dip stick hole and then poured half a bottle of brake fluid in.He said the transmission is gone anyway so the sand and brake fluid wont do it any more harm.The truck ran again but not far enough to get me home I had to get it towed. Now I am wondering if it really was the transmission and not just the torque converter. I guess it doesn't matter now because the transmission is probably toast now.

View 12 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved