I replaced the high beam headlight bulbs in my 09 Sonata, resulting in no high beams working at all. Took out the new and put the old ones back in. Still not working. Checked all the fuses, and the relays. No problems there.
View 3 RepliesFor some reason, the search button isn't working. Anyhow though, I am wondering if there is a way to adjust the high beams on the Sonata? I know how to adjust the low beams but am at a loss regarding the high beams---the owner's manual only tells about how to adjust the low beams.
View 7 RepliesJust purchased a 2009 Sonata and the dealer did not give me an owners manual. In a recent phone call he promised to be mailing one so with that said I've looked on countless forums about this tedious issue I am having. I can't seem to figure out how to turn my high beams on. All other lights are working correctly and from a diagram i read online its like any standard high beam, just pull the lever forward. I've tried every which way but can't even get the light on dash to turn on telling me the high beams are even available. I clearly see them in the front of my car. And driving at night they would make a big difference on those back roads.
View 4 RepliesI have a b6 Passat and the high beams are not working. I am going to be installing HIDS in the next week or so so I located a vag com disabled the drls and enabled Xenon without the shutter. now no high beams. they will only work with the car off and pull back the switch instead of pushing it forward.. I'm sure there are ppl on here with HIDs and there high beams working on a b6.
View 9 RepliesAny mod that will allow the fog lights to remain on when the high beams get turned on?
View 40 RepliesSo I just put in 6000k hid's in my 2011 Sonata Turbo and I want to make my DRL's brighter as well as my high-beams brighter. Is this possible? Also, I'd like to make my fog lights match my HID's, but don't know if I should put HID's in there or LED's.
View 18 RepliesI'm a new owner of an 05 Toyota Prius. Im loving the car so far, however, i am having an issue with my high beams not working. After doing lots of research it looks like the high beams on the Prius comes from the same bulb, what controls the high beams is the reflector.
My low beams and all other lights are working fine. After removing my bumper and looking through all the wiring I have noticed that their are two plugs that are not attached to anything. The lights look brand new, so my thoughts are that this car had HID lights and they were then replaced to non-HID lights.
How to get the high beams working. I don't see any HID ballast anywhere, so converting it back to HID would be costly since i would need new headlight plus ballast and bulbs.
I tried looking for wiring diagrams but can seem to find any.
Here is the link to some images: Prius Photos by Izzy25323 | Photobucket
Driver side low beam was burnt out. I replaced the bulb with a new one then no low beams would work, high beams work. Turning on manual switch and I checked fuse 7 & 10 fuses which were okay still no lights.
Could it be the low beam relay? The passenger side was working. Do they only come on when it is dark enough as I can't remember if they are running lights and worked in daylight?
I've ran into an issue with my high beams on my 07 Camry SE. All lights are working except high beams. When you switch to high beams the lows only stay on. The dash light comes on and shows high beam indicator, but no brights! Fuses look good, and so do both bulbs. Going to go buy a bulb later today just to try. Like I noted they both just suddenly stopped. I'm leaning towards dimmer switch on column now.
View 11 RepliesSo I pullled into a reststop to relieve myself and when I drove off none of my lamps (high,low,or fog) worked. Along with them my blower fan does not work nor the rear defoggers, wipers, spray with wipers, turn signal (hazards do work though). Is there a fuse or relay that connects them together?
View 2 RepliesLow beams work fine. When I push the Multi-Function lever on the column forward to activate the high beams, I have no lights at all. When it is in low beam (middle) position, low beams work fine. When I pull back for click to pass, only the low beams are active. No high beam indicator in instrument cluster. I have:
1. Replaced both headlight bulbs
2. Replaced the multi-function switch on the column. Checked test pins on switch (MF) they are hot when in either high beam position or click to pass position
3. checked fuses (interior)
#8 - power on both sides of fuse
#16 (15a) High beam headlamps, instrument cluster. ***NO POWER ON EITHER SIDE***
4. checked fuses (engine compartment)
#10 - power on both sides
#21 - Power on both sides
#23 - power on both sides of fuse
My High beams for a 2003 cavalier are not working. I checked the bulbs and they are good, The Low Beams Work and my drls work. I switch from low to high and the blue indicator on the cluster panel comes on.
View 5 RepliesSo I bought an 01 GTI last week with a decent amount of things pre-modified including a Jetta front end swap? Anyway the guy I bought it from knew absolutely nothing about what had been done to the car other than the fact that there was an HID kit installed and it was set up to run high beams only.
I figured I'd remove the HID's until i drop some cash on a pair of nice projector housings. I removed them and plugged up some nice sylvania bulbs as per the OEM standard 9007, and figured I'd have no issues... They are still stuck on high beam only... What could be causing this?
I have an 07 with the AFS lighting. bulb error on dash- as I understand it, this has to do with a faulty shield for the high beam on the passenger side. Can this be repaired? Or should I just shell out the 300 for a used one on ebay.
View 3 RepliesI bought a used 2002 Camry (at a discounted price because of a few dings and dents) and the headlights are not working. The high beams and turn signals work but not the headlights. I changed the bulbs, checked all the fuses and got a new relay but still nothing. I brought it to an electro-mechanic and he told me the ECM was busted and that he could maybe grind it down. This seemed odd to me so I called my old mechanic in the states who said he has never heard of an ECM causing headlights not to work and suggested I install a toggle switch. Does this sound like it could work? Could I do this on my own? I'm pretty handy but am a little hesitant to try any electrical work on my car as I have no experience with electrical work.
View 3 RepliesThe turn signals and high beams do not work on my 1998 ford ranger xlt 4x4. I have replaced the multi function switch, the yellow flasher relay checked all fusses and all are good. What could be the problem?
View 7 RepliesI have a 2011 ford ranger XL and I get no high beams. My low beams work fine but when I try to either activate the high beams or pull for the flash to pass they do not illuminate and the indicator on the dash doesn't come up either. I have replaced the fuse with a fresh one, even though it didn't need to be replaced, and also replaced the headlights as well cause one was burnt out.
View 1 RepliesI just bought a 98 F150 V6 Manual transmission 2wd truck. Its a clean truck and I'm liking it so far but its got a couple minor issues. Whats the point of buying a truck if you don't get to work on it??
The High Beams don't work at all. Low beams are fine. I've put new bulbs in, and fuse 16 in the passenger compartment has continuity. I'm suspecting the multiple function switch, because when I pull out to engage the high beams, nothing happens. The indicator on the dash doesn't come on, and the low beams don't turn off either.
The second issue is the coolant gauge doesn't read. When I turn the key to the on position, the needle on the gauge moves up just a bit, but it never moves after that. Anything to check?
There are a couple other minor things like the e-brake light on the dash doesn't always turn on, but I can deal with that.
Recently i replaced the old lo beams on my 06 Sonata for some brighter ones. Roughly a week later while driving home on the freeway both lo beams went out. I noticed when this happened that the ESC, ESC (Off) and green headlamp lights all came on and stayed on for several seconds.
I replaced the bulbs after reading that if you leave the lights in the "ON" position while starting the car there is a risk of them blowing out sooner. I left them in the "OFF" position for about a week, but they blew out again. I've checked the fuses which all appear to be in very new condition.
My searches have lead me to the same solution (replace the bulbs) over and over.
My truck only has low beams. When you move the stalk on the colum backwords it changes nothing, when you move it forwards the low beams go out but the high beams do not come on.
View 14 RepliesI have checked fuse 46 and 47, and installed new headlight bulbs. I have high beams, but no low beams. I have searched this topic but no one has the same prob it seems. My headlight switch has broken. Could it be the headlight switch?
In my manual, it says the 2002 has a fuse panel behind the glove box. I took glove box out but it doesn't look like a fuse panel.