My '96 K2500 w/7.4 is running rough.
I've replaced: cap, rotor, fuel pressure reg, injectors (Bosch Design 2's), plugs, wires.
Had it timed today and it still runs rough. Really rough sometimes. I'm getting no codes.
In the morning when the engine is cool, I'm going to pull the pugs and check them, and verify the plug wires are installed correctly.
I have a K2500 suburban that has a rather aggressive/violent "vertical" shake when braking above 30mph... I bought it about 6 months ago and was told it just had a full brake job all around(receipts provided). The shake has been off and on, mostly reserved to highway speeds, however recently it has been constant at any speed above 30mph... Thinking it may be the rotors. I pulled the wheels off and even though everything looked brand new (as described) I replaced the rotors and put on new pads... did not fix the shake... and I had the old rotors mic'd and they came back good as new with zero need to turn/resurface.
I was told it may be the ABS, So I pulled the fuse... and it didn't fix the issue also I have no light on the dash
I was told it may be a flat spot on the rear drums, so I replaced the rear drums and it didn't fix the problem... the shoes looked brand new and had just as much pad left as the set i was replacing them with, so I left them alone.
I had happened to have new tires put on it, and they advised my pitman arm and idler arm were shot and that they couldn't do an alignment, so I replaced the pitman and idler and brought it back to be aligned which they did... this did not resolve any issues...
I spoke with the previous owner and he said he had the same issues and couldnt figure it.. he said his mechanic replaced the wheel bearings, rotors, pads, calipers, brake lines, ball joints(all receipts provided, and all these parts look brand new)...
The shake is very aggressive it makes the dash jump up and down and vibrates the hood to the point where it looks like it will rattle off.. the pedal doesn't pulse and the steering wheel aside from vibrating up and down doesn't pull or shake one way or the other... truck doesn't pull when braking or during this shake... and the second you let off the brake the shaking stops... and only ever shakes when you hit the brakes...it rides as smooth as can be when not braking...
As title really, it's a 1997 K2500 Suburban 4x4 auto 454. I haven't used the sub for a while but got in it the other day and it fired up all fine and I then looked to see what fuel I had left only to see the needle right over to full. Well I know it is nearly empty and I've never had the guts to fill the thing or should that be had the funds to fill it to the top, so know it is wrong. I got under the truck and unclipped the rear most wiring connector just infront of the fuel tank but the gauge still reads full. I suspect either the gauge is faulty (so is there anyway of checking) or the sender in the tank or wires in the tank have shorted (again anyway of testing without removing the tank).
View 3 RepliesI own a 1996 Jeep Grand Cherokee Laredo V8, and there has been an ongoing problem with it stalling. The check engine light is on and it reads codes about idle control sensor and 02 sensor. I spent a lot of money having both replaced, along with an processor. I had to bring my Jeep to a dealership so they could "marry" the processor to the car. The check engine light went out for about a day, then once the computer reset, light went back on. The codes still read bad O2 and idle sensor despite them being replaced.
The problem is when the car starts cold I have to keep my foot on the gas for a couple minutes or it will stall out. Once it has warmed up the car runs good. I turned the idle pin on the front of the throttle body to try to keep from having to put my foot on the gas but it still stalls. It seems like it is working better in the cold weather. My mechanic says that I may have turned the idle too far trying to fix it and that is why it is stalling.
I just want my car to run without having to warm it up every time. It wastes time and a lot of gas. Could it be something other then what I've already replaced? I don't want to keep replacing the same things and not have it fix the problem.
1996 / 2.2 L4 / 186k / Upper engine rebuild 30k ago
Car was driven on a errand by my mother. Upon trying to leave for home, the car started running very rough, and stalling. From the description she gave on the phone, it sounded like a plugged up exhaust. I told her to get some fresh gas and ease it home after.
When I checked the car for codes, I got 2. A P0300 and a P0122. Okay, so the throttle position switch has taken a dump, that's easy enough. The car has 186k miles, but my constant nannying usually soothes her, so surely that's all, right? God, I wish that turned out to be true.
I pulled the plugs, and #4 was gas fouled and sooty, #2 and #3 looked lean, and #1 was partially wet fouled. There was also gasoline in the oil. When the car would run, it would run the gambit from idling semi rough then stalling out and refusing to restart, almost like it was flooded, to idling scarily bad and no pedal response, to running too high of an idle and idle searching.
Since I have:
Replaced the TPS
Replaced the IAC
Replaced the CTS
Replaced the MAP
Replaced the ICM
Replaced the FPR
Replaced both ignition coils
Replaced plugs and wires
Replaced the fuel injectors
Replaced the PCV
Replaced the fuel filter
Checked the pintle on the EGR (looked good, cleaned)
Checked for Vacuum leaks (as best I could)
Checked the Fuel pressure (40 PSI) (drops to 20 after shutoff)
Checked for exhaust restriction (ran open exhaust manifold)
That brings us to today. New injectors just in, and the engine will run, but rough and loud. It almost sounds like the firing order is off slightly (I am using 1342 or from L to R 4132) and throttle control is almost non existent. It also shuts off when its warm almost like its flooded. No codes are showing. (despite discovering a sensor in back being unplugged and the O2 sensor being unplugged at times).
My 1996 S10 2.2 liter pickup has been having some 'issues'. Truck has been kind to me over the years, but now is running a bit rough. It has an irreguler idle and continues to run this way through all speeds. The blinking code reads "cylinder 1 misfire". I did all the basics. I changed the plugs and wires, ignition coils and fuel filter. Here is where is gets tricky, after changing the fuel filter, it ran great again. Then it started to run rough again later that day. I thought I somehow clogged up the new filter, so I removed the new one for inspection. Realizing there was nothing wrong with it, I reinstalled. Truck ran great again. Went out to drive it to work a couple hours later and it started fine, then after about 10 seconds of running, it went back to the rough idle.
View 19 RepliesRecently bought a 96 4 cylinder 5speed 2wd ranger. 200xxx miles on it and its former owner had a young guy change spark plugs . Truck ran fine before, but after is when the rough running showed up.
A quick check of the plug wires and there locations looked correct and also tested the wires for spark with a timing light attached to them, checked shows all are firing.
Seems to smooth out a bit when rpm's are raised up, but still acts like not running smooth.
I swapped out plugs. Looks like they haven't been changed in a long time .Some of the straps are burnt and are shorter than they should be, but still runs rough, very little improvement .
Check vacuum lines for leaks/breaks and all looked good. removed line off brake booster and plugged, didn't matter.
It doesn't throw and check engine lights. It does smooth out some as the rpm's rise, but still not smooth .
I was driving along the highway cruising at around 100 km/h when out of nowhere the car started driving a little rough so I look down and the ASR (traction control) light was on. I got off the highway, shut it down and fired it back up. The ASR light was off and car running like normal. When I got home I scanned it and these codes came up:
The catalyst code if from my catless turbo-back exhaust which I plan to fix next month with a tune. Anyway I cleared all codes and continued on my way without any other hiccups. So is my MAF sensor dying/dirty? ECU? N75 valve? Boost leak? I'm making a boost leak tester today just to 100% eliminate that variable, though I'm fairly certain I'm good there.
The car is mostly stock except for a few bolt-ons, all of which I've had installed for thousands of kilometers now. Here is what isn't stock, not including suspension, wheels, etc:
Forge 008 diverter valve
034 Motorsports PVC silicone hose kit
Samco boost hose kit
Forge silicone turbo inlet pipe
Eurojet SMIC
custom built 2.5 stainless, catless turbo back
AEM Dryflo short ram intake
GLI MFA cluster
I have a 2008 Sedona with the following trouble codes: P0018, P0300, P0302, P0304
I have replaced the coils and plugs, a torn air intake hose, and a camshaft position sensor for the side of the engine with even numbered cylinders.
It still runs rough has a blinking CEL, and gives the same codes.
I found that unplugging any of the myriad of sensors under the hood will keep the ECM in open loop so that it runs like a dream, but as soon as they are plugged back it, the trouble comes back. I used that fact to my advantage to drive the car to the mechanic a few miles away.
After running diagnostics, he says the ECM is bad based on the fact that the number 2 and number 4 fuel injectors stop pulsing after a couple minutes of idling. He says they are not even getting a signal from the ECM. He does not have the equipment necessary to flash a new ECM and recommends going to the dealership for a new one and getting it flashed there.
My question is, if I am being lied to, what do I need in terms of equipment to get a used ECM, install it and flash it with my VIN myself? If such equipment is cost prohibitive, can I contact one of these companies that sells ECMs and have them send me one preprogrammed with my VIN?
My 03 Sante Fe is running a little rough and is stalling. My Mechanic said this P code was going to run me $1300. I'm not very mechanical , but this just seems very high. He said that aftermarket sensors would not work and only Hundai parts for the fix.........
2003 Sante Fe, LX, 3.7 l engine
So my daughter's 2000 Golf Mk4 with 160,000 miles on it was running rough and had 3 codes stored - cylinders 2 & 3 misfire and a 411 secondary air injection problem.
Having had the misfire code before I swapped injectors around and the error code moved cylinders with the injectors so I attempted cleaning them and also cleaned the throttle body and intake manifold. At this point car still running rough but also started smoking badly.
Replaced the following items:
- Spark plugs
- Spark plug wires
- PCV valve
- PCV hose
- Fuel injectors w/ remanufactured
Hose reconnected between secondary air injection pump and air intake - previous owner had duct-taped it in when he couldn't get it to seal I guess. I've never heard it run.
Car running better, idles more smoothly, doesn't stumble or stall like it did before, no error codes coming up BUT car smokes a lot and the fumes make me feel sick just driving it a mile.
The car had never smoked like this before, hasn't had a whole lot of love the last year or two but no real problems either so why the sudden smoke?
At first I assumed it was cleaner being burned off but that should have been gone in under a minute and this is on-going. It's bad enough to not only be embarrassing but apparently dangerous as the fumes are bad.
04 trailblazer, 4.2. Running rough and SES light on. Had codes pulled and showed p0340 (CMP sensor circuit malfunction) and p0300 (Multiple engine misfire detected). Replaced the CMP sensor and left negative battery cable unhooked for 20 minutes or so to clear the codes. Upon start up no more SES light and idle was slightly better. Within seconds it SES was back and it is again running poorly. Cruise control is no longer functional as well.
View 7 RepliesSo I just had both cats replaced and now the car is running very rough and trowing out mis-fire codes. What could cause this? Going to disconnect the battery to reset the computer to see if that might work.
View 8 RepliesI have diagnostic trouble codes P0K92 and P0K7K set on my 2008 Gen. II Prius. I have searched the forums and cannot locate these two codes.
I started and drove my car for several miles today, then it started to run rough. I pulled over, then called a tow truck to tow my car back home. I have a high-level scanner/code reader that read P0K92 and P0K7K codes.
2002 F150 5.4 v8,,, I had troubles just over a month ago with a po305 code. i got the truck fixed with 2 new coils n some gaskets. I am having these po353 & po171 codes pop up now. The truck is running rough and I am curious to if its just another coil problem or if their is something I am overlooking or just don't know about?
View 1 RepliesThese are the code that keep spitting out. I have a 2002 f150 5.4L supercrewand it is running rough. I had this problem about 3 months back but i didnot get any codes from the computer i washed my truck a 1/2 day earlier, 2days later it went away. this time it has spit out 4 codes a po306/po307/po300/po316. the po307 and the po300 are gone, but the other two remain and it is still running rough 2days later. i had just washed my truck 30min. before, it started happening, is there water somewhere? My dad (long time mechanic) says use wire dry on the cops and it will go away. I have read other post on misfiring and I am still not sure what to do?
View 10 RepliesOur 2007 Avalon with 65xxx miles on it was skipping and running rough this morning. Running a scan with my VAG-COM gave me these codes.
Mode 07: Pending emission related fault codes Address 7E8: 2 Faults Found: P0305 - Cylinder 5: Misfire Detected P0355 - Ignition Control Circuit for Cylinder 5: Malfunction
Would you say it is time to replace the Coil for this cylinder, or should I do more troubleshooting first?
From what I've read on this forum, it appears cylinders 1, 3 & 5 are at the rear of the engine and are a PITA to change. Is there a good write-up or video on how to change these at the rear of the engine?
It's an 04 F250 with the 6.0, and has been there about five months now. The backstory I have been given is that it drove in running rough, gave crank position sensor codes, and the CPS was replaced. That was the last time it ran. Since then, it has had the CPS replaced five times, the FICM rebuilt then replaced three times, the engine harness replaced, and spent some time at Ford. It would only show about 30rpm while cranking. The engineer came and looked at it, said it must be the tone ring on the crank and that's it.
Here's where it's at for me: Cranking RPM peaked out at 57, but the fan rpm was about 180 while cranking and it sounded like it was cranking pretty quick. I disconnected the glow plug module, had another guy crank it while I gave it a quick shot of starting fluid, which it caught and started to run on. It sounded like it was running on fuel for a second, then shut back off and now cranks unevenly.
According to the owner this thing has seen lots of starting fluid in the course of diagnosing it, and there were no odd noises before it shut down so I suspect stuck valves from sitting so long. It did give me a whole bunch of codes which I will post tomorrow, including injector #4 high. I tried to do a buzz test but just got a message saying "unknown code, please wait" and then nothing.
2001 F150 4.6. Just replaced all 4 oxygen sensors and spark plugs. Replaced rubber grommet on brake booster as it was leaking vacuum.
Truck is still running rough hesitating.
Pulled codes came up as PO141 oxygen sensor heater circuit. PO171 passenger side cylinders running lean. Fuel trim outside limits.
Just got a 98 f150 w/ 5.4 4x4 excab. It idles fine but under light accleration. It starts bucking and missing bad, if I step on it, it down shifts and accelerates fine. If I try to maintain one speed it misses bad. It is not throwing any codes right now. The check engine light did come on for like a minute but went back off before I could have it read. I hooked up a scanner just to see if any codes were stored and got p0300 and p0301. I am going to clean the MAF and check for vacuum leaks. I hear the rear plug and coils can get water in them causing similar problems.
View 8 RepliesThe X has been running great, well good enough, lately with no issues. I left work the other morning, and apparently the X didn't want to wake up that early. As soon as I started it up, the check engine light came on and it was running like crap. Had a bad hesitation all the way home. It feels like it is misfiring, but only under load. It doesn't do it if I brake torque it or Rev it up. Only while driving.
The codes I am getting are in the P035x family (typed that way for future searches). P0353 and P0358 are the codes I am getting (along with 4x4 codes for the vacuum solenoid...but that's the solution to other problems not relevant to this!). Being codes for the primary circuit, I popped the hood and checked out the connectors. Both connectors are fine, and tightly connected. I did notice however that cylinders 3 and 8 have other than OEM coil packs on them. These are the only 2 cylinders with those coil packs (they are white and the other 8 cylinders have black coils).
I don't want to just throw parts at it, and I'm not getting a hard miss fire code, just the 2 above. I might try to swap the coils with other cylinders tonight and see if the codes move to those cylinders. It has run like this a few times, but never set a code, and turning it off and back on has "fixed"this in the past.
And just for complete disclosure, while looking for where I saved a password, I found notes from August last year where I pulled codes, and these two codes were present then, with a cylinder 7 hard miss fire code. I replaced the c7 coil with motorcraft cleared the codes, and P0353 and P0358 went away and I haven't seen them since. The plugs are brand new and only have about 1000 miles on them (changed them in September when repairing the misfire and I don't drive it much).