Volvo :: Check Engine Light Blink But Never Got Steady / Fuel Pressure Error Code
Apr 18, 2013
I had a Check Engine Light a couple months ago, and I took the car to the garage to have it checked out. They told me they got a Fuel Pressure Sensor malfunction code, and that the sensor had to be replaced. I did so myself, an it is ridiculously easy, and the car worked fine. I noticed the Check Engine Light blinked a couple of times while I was driving, but never got steady. A couple of days ago, it did. Out of a bad gut-feeling, I purchased a ODBII scanner, and I scanned the car myself. I got the same error code as the garage did, but the sensor should be fine.
View 5 Replies
Advertisement
Today I got the engine light blink a couple of times and then steady on. Parked the car, waited a few minutes, start again just the engine light on (not blinking anymore).
I scanned the car and got this
VCDS-Lite Version: Release 1.2
Tuesday, 06 August 2013, 13:48:09:11637
Chassis Type: 3D - B5 VW Phaeton
Scan: 01,02,03,05,06,07,08,09,11,15,16,17,18,19,23,27,34 ,35,36,37,38,42,46,48,49,52,55,56,57,61,62,65,68,6 9,72,76,77
-------------------------------------------------------------------------------
Address 01: Engine Labels: None
Controller: 07C 906 018 C
[Code] .....
I have a hard time believing that all coil packs went bad. My wife told me that when she was driving the car she could hear a clicking noise coming from the trunk so I think this could the fuel pump not giving enough fuel but I was hoping to get an error for it.
View 11 Replies
I have a 2006 S60 2.5T with 40k miles. My check engine light went on and stayed on for two drives. Then turned off and hasn't returned for next couple of drives. Error code says fuel pressure regulator. Should I bother to bring it to a mechanic or since the light went off (didn't burn out -- it momentarily turns on when I start the car) should I assume all is well?
View 2 Replies
What are the common misfire problems with the mk4 R32? My R is acting funny every once in a while it runs perfect then some other times it seems to big and the check engine light starts to blink but doesn't stay on I ran for codes and it said I had a miss fire but after that the code never came up again but it still blinks.
View 7 Replies
2001 volvo s40. Diagnostics performed. Error codes for the timing belt and temperature sensor. These were replaced. The check engine light still comes on/stays on.
View 6 Replies
A few days ago my "Check VSC" warning came on along with the check engine and traction lights being on. I left my car in a parking garage for a week when I was on vacation and the lights came on once I started the car after getting back from my trip.
I have had the "Check VSC" warning before and I fixed it by replacing my gas cap. My gas cap seems fine this time around so I got my codes scanned and the only one that came up was P0300. Having this issue with the 2007 Lexus GS 350? I still feel like it's my gas cap because I bought a cheap replacement last time around.
View 8 Replies
2001 F150 5.4 Auto ... Truck was running excellent. Engine light and overdrive light begins to blink and it acts like its running out of fuel or water in gas. Baring made it home. Cleared the code and it comes back. Transmission seems fine.
View 2 Replies
I have a 2011 F-550 XL truck, I had a problem with an open injector4 and was forced to replace the engine, later, I had a problem while installing an OLEP kit, misplaced the hose and killed the engine (...i know... ) so, I changed 3/4 of the engine, just mechanical parts and reused the wires and cables, now the check engine light is ON with an oil pressure error, replaced the sensor and the error remains, replaced the computer and guess what ...again, the same error. What might be going on?...
View 1 Replies
1994, 960 ... The vacuum controller has two "vacuum lines" attached to it. Should both lines have vacuum present? I keep getting a 241 code with sporadic idle and check engine light.
View 3 Replies
2003 1.8t passat wagon. 50k miles... The check engine light came on today. Oil and engine temp are fine. Can most shops plug in and diagnose? Can I get one of those code readers at Advanced Auto parts to read the error code?
View 5 Replies
What is the meaning or the fault concerning 4608. The above error code was reported on the computer diagnose machine and it referred me to look into the vehicle ownership manual book BUT its rather unfortunate that i could not find that book. So, what to tackle or replace on the engine to enable the check engine lite go off.
View 17 Replies
I got a P0118 error code on my car. Looked up some things and most people were saying change coolant temperature sensor. I changed it 2 days ago and have not had a chance to clear the CEL. Its still on now, guy at Autozone would not clear it, said it was against company policy.
Will this turn off automatically once problem corrects itself? I went to Autozone and had them rescan the error, this time another code poped up P0444, EVAP(Evaporative Emission System)Evaporative Emission Control System Purge Control Valve Circuit Open. What this can be?
View 3 Replies
2004 XC90 T6. Local Volvo dealer (Bangkok at the time) said my check engine light was due to the O2 sensors going bad. I changed out the one under the car, then my wife threw out (accident) the other so I didn't change the one accessible from the hood. The check engine light went away so I figured that was that.
Fast forward a year later, I buy an Autel Maxiscan MS509 and now I'm getting check engine code P0455 which is probably the O2 sensors I didn't replace. Other than deductive reasoning, is there some way to look at the data on my OBD reader to confirm which O2 sensor is bad?
View 4 Replies
I have a CEL on my 2007 Avalon so I decided to take it to Autozone to get a scan. Error code P0015 was returned. This code has to do with B Camshaft Position, Timing Over Retarded (Bank 1). I've done a little research and I've read that this could possibly from a dirty screen on the Oil Control Valve, the OCV itself, or the Cam Position Sensor. Before replacing parts, what I would like to do first is to check/clean the screen on the OCV. Secondly, I would like to swap the Cam Position Sensor to a different bank and see if the other bank throws an error. If the other bank throws an error, then I know the sensor is bad and needs to be replaced. With this said, I am having trouble locating the OCV and CPS. Where the valve and sensor is located. A diagram would be useful.
View 14 Replies
I got a 2012 Hyundai Accent SE manual 112000 mostly highway miles. For a month now I am getting the MIL on and P2191 code (System too lean at higher load bank1) after erasing the code it appeared again in 3-4 days. I replaced air filter check all valves and vacuum in air flow, changed to premium gas. Pipe that connected to the valve from EVAP system looks not damaged and valve works as intended. While changing spark plugs I noticed that all of them were quite charred. I am thinking to replace both O2 up/down stream sensors. Which not OEM sensors would be the best match for my Accent?
View 11 Replies
I recently bought a 2007 Hyundai Sonata Limited from a private seller. This car has been perfect for the few weeks I've had it. Now, my check engine light came up and the error code "P0660 Intake Manifold Tuning Valve Control Circuit / Open Bank 1" popped up. I'm not really sure what piece to look for, or which connectors to check.
View 3 Replies
I have a 92 volvo 240 and have recently got a check engine light. I got a code reading of #241 on number 6 terminal. What that means and how to correct this problem?
View 1 Replies
I bought a 2005 Volvo V70 with 75,500 miles on Nov. 13. On Nov. 15, the check engine light went on, and I returned to the dealership for a solenoid replacement. The check engine light went on again on Nov. 17, oil pan replaced. On Nov. 19, the light went on again, timing belt replaced. On Nov. 22, the light went on again. Each time the code was the same--sometimes in conjunction with other codes--but one code was consistent. We returned the car on Nov. 22 and asked for a refund in keeping with the Massachusetts lemon law (an attempt at repair 3+ times). The dealer refused, saying the check engine light and computer code were not the same as an attempted repair. He took the car and said he was going to call Volvo Tech in. However, he says the light "went off" and never came back on even though his staff has test driven it 170 miles in the past three days. He's "releasing our car" to us, even though he has made no repair. Tell me--is trying to address the same computer code considered a "repair"?
View 13 Replies
I am far from home. Taking a road trip. Day 2 out of 6. My check engine light came on, so I just pulled over. All fluids were fine. Found some place to read the code:
P2757 TCC pressure control Sol Ckt Perf / Stuck off
The guy said it was something to do with trans.
View 3 Replies
From time to time, the engine lights comes on with error code P0365, it usually disappears within two days (it disappears by itself), but it appears once per month and stays for two days.
The code scanner says :P0365 Camshaft Position Sensor B Circuit Malfunction (Bank 1)
Do I need to change the sensor? and where is it located?
my Sonata is 2009, 2.0L (Korean imported) 4 cylinder ...
View 8 Replies
I was driving along today and my Check Engine light came on. I stopped at the nearest Advance Auto to have them pull the code and it came up with the P0420, Catalyst Efficiency Below Threshold (Bank 1). I asked what could cause this and they mentioned that the fuel that was put in could be causing it. They didn't mention any other possible causes. Any others? I'm thinking it could be the fuel because the last gas station that I stopped at and filled up at is one that I never go to, and maybe just got a bad batch of fuel.
View 14 Replies
