Chevrolet - Suburban :: 2002 - Engine Stalls At 75 Mph
Apr 9, 2014
2002, Chevy, Suburban 1500, 4wd, 5.3L engine, 210,000 miles. Mass airflow sensor and both O2 sensors replaced last year in an effort to fix this problem. Original problem surfaced when the vehicle was shut down or running uphill and had about 1/2 tank of gas in hot weather. If stopped, the vehicle would not start until it had cooled down. Sometimes getting it onto level ground would be enough to get it running again. ( This accomplished by turning on the key and allowing the vehicle to roll back out of the parking place. ) If running down the road, getting to level ground after the stall, pulling to the shoulder and cooling the engine/waiting a few minutes and restarting the vehicle would work. This was before the above mentioned repairs.
Last weekend in 60 degree weather I was driving back from northern Michigan and as I headed up hill at 75 mph with the tank at 1/2 the vehicle did a high speed stall on me. Symptoms were: RPM showed 2000, but pushing down on the gas actually dropped the RPM no matter how feather-footed I was. This was tried several times. I turned on the 4 ways and moved toward the shoulder and at 50 mph finally got the thing to restart. The rest of the trip home was uneventful.
I had a 2001 Suburban with the same specs which did this same thing until a factory recall that got me a new fuel pump. I asked about the recall the last time my truck was in for service and they said it does not fall within the serial numbers for that recall. Fuel filter replaced about 9 months ago. Co-incidentally but not necessarily related is that my battery with less than 3 years of a 7 year warranty was draining itself in less than 2 days this last winter.
View 8 Replies
Advertisement
I have just swapped a new Vortec V-8 engine into my 1999 Chevrolet Suburban K1500 4*4, now when I start the truck and put it into reverse (foot still on brake pedal), I let off of the brake and the next time I step on the brake pedal the truck stalls. What would be causing this? I have no error codes on the computer, my fuel pressure is good, I just replaced the fuel pump. I think that it might be a sensor somewhere, but I am not sure where to look.
View 2 Replies
After driving through high water (only 12"-18" deep), my 2002 Suburban stalled. It restarted but runs rough, doesn't idle well, and still stalls and sputters under acceleration. A week later (it's been dry and I've driven it 70 or so miles since the water), it's still stalling and sputtering. Under braking, I must keep the accelerator down enough to keep the RPMs slightly above 1000 or it will stall. Obviously something got wet that shouldn't have gotten wet.
View 1 Replies
I have a problem I have been struggling with for the last year.... Here are the main symptoms:
- Engine stutters and sometime stalls ONLY in 3rd and 4th gear
- 1st and 2nd gear has NEVER given us a problem
- The outside temperature has to be above 75 degrees. The truck ran great all winter, but last week with the first warm day, acted up again
- There has to be a sizable load (6 adults, full tank of gas)
- gets much worse going up hills (again load)
Not sure if it is related but one time in the winter, the truck stopped blowing heat. If I turned off the fan, the system would "build up" heat but then as soon as I turned it back on, the heat would stay for maybe 30 seconds and then fizzle out back to cold air. This happened only on the coldest day of the year. The heat has been decent the rest of the time.
Last year they replaced the crankshaft position sensor like 4 times, then claimed it was the ECM, replaced that and it still acted up. Then they finally said it was some corrosion in the wiring harness. However by the time they got through with it, it got cold enough outside where it didn't act up any more.
View 6 Replies
OK so - I had the rear axle bearings replaced, but I'm still hearing a rotational scraping noise while moving (whether gas is applied or not, or whether braking is applied). Gets slightly louder the faster I go. But when I turn, the noise goes away. It's hard to pinpoint where the noise is coming from. My wife swears it's in the front; to me it sounds like it's in the middle (so it would be being transmitted from the source).
I took it back to our mechanic, but he can't hear it very well - he admits that his hearing is not what it used to be (he's in his 70s). Only thing he hears is "gear noise in the rear"... meaning he'd have to replace the differential in the back which would be prohibitively expensive and not worth it. He said I should come back in a couple weeks when his younger employee will be back so he can listen for it.
View 6 Replies
Noticed this during a recent trip halfway cross country. It did POUR for part of the trip, but I didn't notice the wetness until a few days after we were at our destination. Further, none of our luggage etc was wet, so I don't suspect a leak in the rubber gaskets along the window. We did have the A/C running constantly while in 90° heat. I checked underneath the car; saw no obvious signs of rust on the underside. I did see a hose and some type of contraption on the passenger side rear, above the muffler - it was dripping water. Is this part of the A/C system, and could it be the cause of dampness in the carpet?
View 1 Replies
I have a 2002 suburban . I have a humming noise coming from the rear . It starts at 45mph and then goes away at 47mph. I hear it again between 60-65 mph then goes away . This is a faint sound . When pulling a trailer the sound is much more noticeable and more constant from 55-64 mph . When I let off the gas the sound is still there and fades as the truck slows. Am I dealing with a bad tire ( I plan to rotate them to see if that is the cause ) or a wheel or axle bearing ? To note I replaced the front wheel hub/bearings just about a year ago .
View 2 Replies
2007 Chevy Suburban, 65K milesLet me start by saying I took this into to the dealer and they found nothing!
When I accelerate, I get a "flutter" in the engine. The best description of this flutter is that the RPMs go down about 200 or 300. I think it feels like it is sluggish when it accelerates. It is most obvious during the 35 - 60 MPH range, but you also see it when cruising at 70 MPH.
I tried adding some fuel treatment and ran some 93 octane through it to see if it was the fuel injectors, with no change in the behavior. No error messages or engine light is on. Regular oil changes and services (60K service, every 3K miles for oil change). Driving behavior has changed since I bought a Prius 3 months ago. It used to be driven 40 miles / day (+ long trips) and now is driven about 40 miles / week (+ long trips).
View 1 Replies
My engine revs up no matter if the thing is hot or cold when I come to a stop at a red light, SOMETIMES. Other times it will idle at 100 and then wants to idle around 1000 and has idled as high as 1200. I've been told EGR, TPS, Idle Control Motor, or Intake gaskets. I did have a code 22 which occurred after a friend unplugged the TPS and reconnected it, but no other codes or check engine lights. Tuned engine 2 weeks ago, but problem still persists. Where do I start and what equipment do I need. I am a professional diesel tech, but not so much with gas.
View 3 Replies
My Burb starts right up when the engine compartment is cold. Can barely touch the key and the thing fires right up.
Once engine compartment is hot (operating temp), I shut off the motor, let it sit for a few minutes and I get about 3-5 seconds of dry start each time I start it. It fires right up, runs great after that dry start period.
The dry-start behaves as if it's starved for fuel for those 3-5 seconds.
It's a K1500 with a stock 5.7l (350 ci). 180,000 miles and the entire drivetrain runs like a top. Only mod I've made is a K&N cold air intake.
Here's what I've done/changed recently (i.e. within the past 5k miles):
Fuel pump, OEM installed by dealer.Fuel filter.Ignition control module, BWD.Ignition coil, BWD.Crankshaft position sensor, GM OEM.Engine coolant temp sensor, BWD.Oxygen sensors (all four), GM OEM.Catalytic converter, replaced one of the two.Plug wires, BWD.Plugs, Delco OEM.Distributor cap and rotor, BWD.Cleaned ground connection (bolts to frame) for fuel pump.Alternator, new not reman.PCV valve.Battery.
Full diagnostics by a very qualified shop two weeks ago, no bleedback from injector spider, fuel pressure solid and holds perfectly. After 90 minutes of troubleshooting, the mechanics finally gave up.
One last thing with potential that I can think of is that I started running ethanol-free gas around the same time this issue surfaced. Not at the exact time, but at a relatively similar time. Gas mileage has increased by 40% and power increased, hard to blame "bad gas."
View 19 Replies
I have a 2002 Chevy Cavalier that stalls ever time it is fueled at the pump. It then continues to stall. I have to pump the gas like the old days when we all had carburetors and repeat the action many times. It always starts eventually, but causes unnecessary anxiety so I always fill my car at a time I don't need to be anywhere in a timely manner. It was taken to the shop but they could not reproduce the stalling, as they did not have the information that it mostly happens at the when fueling. The gas cap can be taken off for a while and it starts okay. The rpm is low after adding gas, if you give it gas, it runs then eventually idles normally.
View 6 Replies
My '97 Chevy Suburban diesel dies at random times. Nothing seems to trigger it; it usually happens when I'm just driving along, minding my own business; not accelerating or decelerating, turning, stopping, etc. Has happened with the fuel tank at every level: full, half full and quarter tank. When it dies, the dashboard lights do NOT come on. When I turn the key "off" and back "on", the lights come on and the engine will crank fine, but won't start. Ten minutes later, it starts and everything is fine. It may not do it again for weeks, or it may do it again in 10 minutes.
This last time, the fuel tank was fairly low -- below a quarter tank -- and it seems to "buck" or "hesitate a little just before it died the first time. The dealer replaced the crankshaft position sensor and the fuel injector pump. When it started doing it again, they ran every diagnostic test they had and could find nothing wrong. Ran fine for a few weeks, then quit three times in 30 minutes. It's back there now.
View 11 Replies
I have issues with engine starting when cold outside or after rain. This only happens when engine is cold and has not been started for a day or 2. Distributor cap does not have any condensation inside but does seem to corrode on contact points. Engine turns over fine, has fuel and spark. When this happens engine will not fire and after awhile it will start to fire and lock up when it fires then continue cranking. After repeated attempts it will start and run fine, can be shut off and start right back up with out any issues. It could take a few tries to a few hours of trying before running though. I'm leaning toward a distributor or timing issue. Am I on the right track? 98 Suburban K1500 5.7L ....
View 6 Replies
I replaced the oil pressure switch on an '07 Suburban 5.3L because the oil pressure was showing low once the engine warmed up. That did nothing, then I found out about that little filter/screen under the sensor. I intended to remove and clean the filter then reinstall it. While I was pulling it out, I dropped it back behind the engine and couldn't find it. I checked online and found a few people in other forums that said to just remove the screen as a "fix", so I left it out and put the sensor back in, just to get the vehicle drivable. It started right up and ran fine for me, parked it, and a after sitting for a few hours it started popping while driving with the SES light flashing on the drive home.
Code P0300 was set, no cylinder specific misfire codes were present. I checked the misfire data and cylinder #6 showed tens of thousands of misfires, #5 showed several hundred, but I think it was just picking them up from #6 since #5 is right after #6 in the firing order. I disabled each injector with a scan tool, all changed the idle except #6, it did absolutely nothing. #6 fuel injector had good pulse to it, I connected a fuel pressure gauge and put power/ground to injectors #6 and #4, both dropped the same fuel pressure. I did the "cylinder deactivation" test on the scan tool for the four cylinders that have it, they all did the exact same thing - the engine bogged way down for a couple seconds and then died. Is that normal? I can't say I've ever seen a V8 engine die before when running on 6 or 7 cylinders. I checked compression on cylinder #6, it showed very low, almost zero, but I tried it a few times and it would show just a little compression at times... valves staying shut? I'm thinking when I opened the pressure relief valve on the gauge and the piston was near the bottom of the cylinder may be when it showed some compression. I also switched the coil/wire/plug from #6 to other cylinders and the miss did not follow.
Could having that screen out cause this problem? Having the engine die when deactivating the cylinders makes me wonder if maybe it's commanding all four at the same time, although the test shows each cylinder being controlled separately. Using a MODIS, not a TechII. I just got done putting in a new filter/screen to see if it would make any difference, and of course it didn't.
View 3 Replies
I have here a 2001 3/4 ton Suburban. It arrived last fall with 280K miles and a 6.0L V8 that was on its last leg (low to no oil pressure). I dropped in a 5.3L that I had handy, and had been happily driving it throughout the brutal Minnesota winter.
A couple months ago I noticed an issue developing. After a cold start, the engine would be severely lacking in torque for the first minute or so of driving. You could reach any RPM you wished, but the truck could barely accelerate. Once a minute or so had passed in this fashion, the issue would suddenly disappear... you'd be thrown back in your seat a bit if still attempting to accelerate, and the truck would take off. For the remainder of the trip, things would be fine.
Recently I went to drive the truck after it had sat for some weeks. It started fine, but the issue was now more persistent. When trying to accelerate, the gutlessness would continue for a good 15-20 seconds until finally and suddenly disappearing. Let off the gas, wait a moment, try to accelerate again, and it was the same thing all over again. Eventually I also noticed very obvious stumbling/missing when trying to get moving from a dead stop. Idle remained smooth.
The plugs and wires are only a few months old. The fuel filter is new. I checked for vacuum leaks (none that I could find). Fuel pressure is consistently around 50psi, even while the issue is happening.
The MIL was not on. I checked with my scantool, and found that P0101C was set, with P0101 pending. Visually examined the MAF harness and sensor; all looked fine. Swapped in a used working MAF; no change. (I suspect these codes may be due to the fact that I'm running a 5.3 with a stock, unmodified 6.0 PCM.)
My scantool is a Genisys running System 2.0. I'm by no means an expert with it, but I did know enough to try watching the miss counts while the symptom occurred. All cylinders seemed to be missing equally as much as the others, more or less.
Normally I'd be suspecting the fuel pump and/or associated wiring was going bad, but the pressure seems fine. What I might be missing?
View 10 Replies
2003 Chevy suburban, 115K miles, accelerating I hear a squeal/groan/clicking noise coming from right front of engine. Did not happen this winter, started again in spring. Loses power if stay on accelerator. If let off and then reapply, it will momentarily go away. Appears to be only when air conditioning on. Bad AC or just the pulley?
View 1 Replies
I checked the cables, no corrosion and tight as a drum. I connected an OBD II computer to the plug under the dashboard and the computer replied that there were no trouble codes present. Is OBDII the proper code reader? none of these lights were on before I replaced the battery. now I have constant ABS, flashing Service ride control, change engine oil. The battery has not gone dead as of yet but the ampmeter is charging at about 16.5-17 volts. I disconnected the pos terminal while the vehicle was running and it continued to run even with the lights on.
View 2 Replies
Trailblazer 2008. This has happened 6 or 8 times. When fuel tank is 1/4 full or less, decelerating downhill from 50 mph to make a right-hand turn, the engine stalls as I reach the turn. Of course I lose power steering and brakes.
If I stop in that downhill position, the fuel gauge reads ZERO but the Low Fuel light is not showing. Turning the key to restart does not restart the engine but if I roll to a flat piece of road or to an uphill position, the engine starts immediately on turning the key. The fuel gauge continues to show ZERO until I turn off the ignition completely and restart. Then the fuel gauge immediately returns to indicate 1/4 full.
No warning lights of any kind show on the dash. There is no question of the gauge showing a false 1/4 indication when the tank is actually empty, since I can drive for 30 miles after the incident while the gauge slowly drops lower until I fill up again with gas.
SOMETHING tells the engine it has no gas so it stops. No stutter or indication of fuel starvation. Simply an engine shut-off.
I tried to reproduce the effect immediately after it had happened by turning the car round and retracing the route, but it did not happen a second time at that location, but it did repeat a few hours later at another intersection.
View 6 Replies
2004 Trailblazer 6cy. 2WD - has been experiencing a very rough idle, engine shudders - no matter how long it's been warmed up. Wants to stall off red lights and at very low speeds. Not throwing any lights yet - but the speedo is out ( a cam shift typical problem for this car) so I don't trust the console for lights. Worse when the heat or air is on. Rides fine with more gas/higher speeds. Definitely worse in colder temps but continues even after 40-50 mins of driving. I've heard a number of things, but can't afford to fix them all. I've heard plugs, dirty throttle camshaft, sensors, cam actuator solenoid, etc. All seem to have people who said it fixed and didn't fix the issue. Worried I'm going to stall pulling off a stop and rear end someone any day now. Where do I start!?
View 2 Replies
We've had two problems within the last week with our 2002 Sport Trac (4.0l SOHC engine w/167,xxx miles). They may be unrelated, but I suspect there's good change they are. Both incidents happened while my 16 yo daughter was driving, so there's only very limited info on what happens. Both times, when I get there, it starts and runs fine. There is no CEL.
The first time it apparently stalled as she neared her destination after driving only about 2-3 miles at 35 mph or less after a cold start. She was slowing to pull into a parking lot and reported the dash lit up with warning lights, no power steering assist and no power brakes and no power from the engine. When I arrived it started and ran normally. She had fulled up the day before after two days of heavy rain, so I suspected water in the gas. I drove it more than 200 miles within the next 24 hours under a variety of conditions and filled up at a different station. I experienced no problem what-so-ever, and didn't bother adding any dry gas.
Then 5 days later (still on my fill-up) when she tried starting it after sitting all day, she reported the engine started but ran rough before stalling and never idled normally.
Doesn't the fact there's no CEL eliminate a lot of the upstream part of the control system......like sensors and actuators? This leaves things like the downstream parts of the fuel and ignition systems. I.e. from the fuel tank / pump to the injectors and the downstream parts of the ignition system.
What are the possible culprits? Fuel pump, fuel pressure regulator, injectors, ignition module, spark plugs, and....... what else? (I'm not that familiar with what these engines have) And of the possibilities, what are the most likely causes.
View 4 Replies
I have an odd issue. I bought my car used from the dealer. The fuel pump was replaced last December, as well as had an oil change. The fuel pump died right after the oil change but are seemingly unrelated since the pump was bad when i bought it. After the pump was replaced my van stated acting up over the next couple days. The fuel gauge would dance randomly. That has since settled down. Now when i make left turns, the rpms drop and i have to pump the had to get it going again or else it completely stalls out in the middle of an intersection. .. it had been steadily getting more frequent and only on left turns. Right turns runs fine.
View 3 Replies
