My dad's 1996 Chevy Silverado will not shift into hi gear. The truck starts up fine and he can drive it but for some reason it won't shift into hi gear. Him and I are clueless as to why it won't. He has a 1996 Chevy Silverado, 6.5 liter V-8 automatic transmission, and its a diesel. We really want to fix the truck ourselves so we are trying to avoid taking it to a shop.
View 2 RepliesI have a 98 Chevy truck with a 4L60E. It has no second gear. I was sitting in park for about 10 minutes with the engine running, then put it in drive and it never shifted into second. It felt like it went straight to 3rd. I played with it manually until I figured out I had reverse, 1st, 3rd, 4th and torque converter lockup, just no second gear. My acceleration rate was medium and when I reach about 27-28 mph it would shift from 1st into 3rd. It has 230K on it so I rebuilt it with all the typical parts - frictions, steels, band, sun shell etc., still no second. I then pulled the pan back off and replaced the spacer plate and put in a shift kit. While I had it down I put a corvette servo in and did an air check. It worked fine. I could feel the band tighten.
Both the 1-2 and 2-3 solenoids checked good at 23 ohms. I swapped their positions to see if it would make a difference. I also checked to make sure the 1-2 accumulator piston wasn't stuck in its bore, the spring was new from the shift kit. It was fine. Put it back together...still no second gear. When I originally pulled the pan off for the rebuild, the pan was free of any debris and was very clean. I then drove it a couple of miles to a local transmission shop. They put their scan tool on it and drove it around the block. There were no codes and the ECM was calling for second gear. It doesn't sound mechanical since almost all the parts have been replaced, rebuilt or inspected that affect the 1-2 shift. It sounds electrical. Is there anything I have missed?
I have a 1996 Silverado and it will not shift out of first gear. I have had the pickup for about 6 months and when I got it, it would shift if I accelerated to about 30 and let off but then I went though some mud and got stuck, I kept shifting from reverse to forward and I got out of the mud and it would not come out of first but reverse works fine and it will not shift manually at all the pickup has a 4l60e transmission.
View 5 RepliesI have a 1993 Chevy Silverado, 350, 2WD. It has a 4L60E transmission. I just started having a problem shifting from 1st to 2nd. When accelerating the RPM's go way up and won't shift until I let off the throttle. Then it shifts into all other gears normally.
If I accelerate slowly. it will shift into 2nd at about 16 MPH. It will then shift into all other gears normally. I have replaced the Throttle Position Sensor, flushed the transmission and replaced the filter and fluid. This made know change in performance.
I am now suspecting that it might be the 1-2 shift solenoid. The check engine light is not on and everything else works fine.
I have a 96 chevy Silverado 4x4 5.7 motor and it does the same thing but it doesn't leave in first gear, it misfires and high rpms and doesn't go in overdrive. but if I drive a little while and turn it off, it's fine it acts like a normal truck would. then if my truck is off for more that a couple of hours it goes back to it acting up.
View 1 Replies01 2500hd, 8.1L allison auto, push button 4x4. wont lock in until its about 2000 rpm then will release just fine. Just not sure of where to start looking for the problem. Actuator on the axle or in the transfer case or something else?
View 2 RepliesI am trying to get some advice on a diagnosis for a transmission problem i'm experiencing with my vehicle? It's a manual transmission and the sound i am hearing is when i shift gears is a loud whirling grinding sound. It's really loud in 2nd 3rd and 5th and doesn't stop.
View 1 RepliesI have a 2001 Chevy half ton 4wd. It has the 5.3L, 4L60E transmission, and a 246 transfer. I am having problems with shifting. if I out the truck in drive, the trans will wind out in 1st gear and not shift. I then pull it down to 2nd and it will shift. When it comes time for third gear, it will not shift at all. It just simply revs until it catches up with the speed at which the truck is rolling. I thought it was a bad tranny as I smoked one and replaced it with a used one so we rebuilt the tranny and it still does the exact same thing. Also the speedo is not working but the odometer is on. Don't know if its registering anything but its on. I have also checked every single fuse and maxi fuse in the engine compartment and the drivers side panel.
View 1 RepliesI have a 92 chevy pick up 5.7 with 159,000 miles. The truck runs and starts great but shortly after I bought it 3 years ago it developed a sort of misfire at higher rpm's, it's fine if I drive it normally but if I try to pass someone it will downshift then fall on it's face, (spit,sputter and slow down). some times I can feather the accelerator and it will come back again. I normally don't drive the truck in the winter but this week I was forced to use it and the cold weather is seriously affecting it, it took forever to get it up to 70 mph after getting on the highway. once up to speed it will do 75 all day without an issue.
I've replaced the plugs, wires, pulled the throttle body and cleaned it as the port for the pcv valve was plugged solid with carbon. I have not replaced the cap and rotor as they seemed to look fine. I have not checked the fuel pressure because it will break the tires loose upon take off and I don't think that would be possible if the pressure was low, would it?
I have a 2001 chevy cavalier, the base 2.2 model with a 5 speed manual transmission.
I can't shift into 1st, 3rd, or 5th gear. On occasion I can get into 1st but it pops out almost instantly. I have the shift boot up, it looks like the shifter won't go far enough to click into gear for the top 3 gears.
2nd and 4th don't have any issues, reverse works as well though can sometimes be more difficult than usual.
I have a 2011 Chevy Malibu, with a little over 100k miles on it. A couple weeks ago it started acting a little funny when I would shift into reverse after starting it after sitting for a while. I thought it might have been due to temperature as it didn't do it after the car had warmed up or when it was warmer out.
Yesterday it started acting up really bad, will not shift out of first gear, and will not shift into reverse, and the check engine light came on. I was able to get it up to O'Reilly's to get the codes. It came back with 2 separate codes.
P0700 - Transmission Control Module (TCM) Requested MIL IlluminationP0776 - Clutch Pressure Control (PC) Solenoid - Stuck Off
The guy there seemed to think that the second code was probably caused by the first one, and most likely the TCM needs replaced. It makes sense to me, but before I head down this path I want to get some input, as it is a little over $300 for the part.
I have a 2007 Chevy Malibu with around 190000 miles on it. Recently, first thing in the morning then I start driving, that car will not shift into 2nd gear for a bit. The engine will rev up the 2000 RPM and stay there. After a while it will finally shift. The fact that the engine stays revved that high for that long makes me nervous.
View 9 Replies97 Silverado - 5.7 with 4l60e trans. truck will not shift into 2nd gear while driving. stays in first gear until rpm are high and shifts into 3rd. under hard acceleration will stay in 1st until let off gas then shift into 3rd. manual shifting results in same, no 2nd gear until selector is moved into 3rd then shifts into 3rd. Haven't got any trans codes, fluid change netted no change in performance, fluid was pretty dirty but didn't smell burned, and there were no metal shavings in pan.
View 9 Replies1996 dakota v8 automatic 4x4. tranny rebuilt 3 years ago got stuck in the mud and every since then it is stuck in first. wont shift no matter what i tried to adjust the tv cable and it didn't work at all. don't know much about dodge transmissions iv always worked on 4l60e in chevys. I don't know were to start. Where to start. iv been reading about the governor valve and shift selnoids are there any way to test any of this? first pulls strong and reverse works
View 1 RepliesOn my 96' F-250 4x4, The tranny will shift to 3rd gear and that's it. If I put it in Neutral and then back into drive it will stay in 4th gear for about 15 seconds then go back to 3rd. What could be causing that?
View 14 Replies,My wife drives a 96 Civic DX Hatchback, 5 Speed. It has about 160,000 miles on it, and she only drives it to work and back (a 15 minute drive via the interstate).
Just yesterday, she told me that the clutch feels 'looser' than normal, for lack of a better term. When it's first started, it's hard for her to get it into first and/or reverse, but once driving, she says the shifting is fine. When she's driving at highway speeds in 5th for a while, then has to get off at her exit, she said it's hard for her to get it back into 1st gear. She says she feels like she has to push the clutch harder than normal to get it back into 1st gear.
I don't know much about manual transmissions, and am hoping for some insight into what the problem(s) may be?
I have a 98 chevy truck that won't start. After it sits. It was starting after cycling the key a few times. But now it won't start. Could it be the pump? I hear it running.
Or could it be the regulator? It was running good after it started. No check engine light, no gas smell, and no rough idle.
The cruise control on my 2002 Chevy 1/2 ton Silverado doesn't work. Went to boneyard and bought a module but it didn't fix my issue. Borrowed a multimeter and tested the cruise control module plugin. The only pin that came up with a incorrect reading was the first brake test. It's suppose to have 12 volts with brake pedal up but showed about 30, so I changed the brake light switch. Still no cruise control.
Since I have a high reading on the brake pin, do you think I have a wire issue there or would my problem be in the multi switch wires by the steering wheel?
I have a 92 chevy truck with a 350 engine that came out of a 93 chevy my problem is my module in the distributor keeps going bad when i spoke with the previous owner of the motor he told me that he had the same problem and advised me to change the distributor. So I took my distributor out of the original motor and put in but the problem still exist, also I have noticed that I have nearly twice the exhaust coming from the drivers side tail pipe as I do the passengers side.
View 1 RepliesOn my 1999 Chevy Silverado Z71, a gurgling water sound is present everytime I accelerate. Are there any other Chevy owners that have had this same problem? If so, how was it resolved?
View 14 RepliesThe issue I'm having is the A/C. When I got the truck the A/C was completely freezing. Recently however, the compressor was having issues not engaging and I fixed that by simply plugging the cord to the accumulator thing. . Now the compressor engages, but is not cooling really at all. It is an old truck and the compressor is a little worn from what I see maybe 2mm space when not engaged. I checked the levels of freon/coolant with a gauge and the amount is perfectly fine. Plus there seems to be no leaks.
View 1 Replies