My son has a 2007 jeep compass 2.4l engine. He needs to change the crankshaft position sensor. Where to find it? He got a pic from autozone but you can't tell where it is on the engine.
View 7 RepliesLooking for a picture or description where this sensor is located? I assume very close to the crank pulley, but I'm hoping I will not need to remove the crank pulley to gain access to this sensor. I have a 2011 Sonata, 2.4L engine.
View 3 RepliesI have been getting a P0011 error code. Changed the OCV but the code continues. I'm going to try replacing the CMPS but am not quite sure of the location on the 2007 Sonata GLS. Looking for any pics of the location or a description?
View 1 Replies2000 jetta vr6 manual 150k miles, i have trouble starting the engine so I thought i'd start by replacing the crankshaft sensor. I notice that its wet with oil when i pull it out, and wasn't sure if tits supposed to be dry. I may have a bad ECU in the end...
View 1 RepliesMy car doesn't start right now and a shop diagnosed it as an ecu, but I'm starting to think that is not the case. The tach doesn't move when I try to start it and pushing the gas doesn't change it, so I'm thinking it is the crankshaft position sensor. Unfortunately, down at school, I don't have access to a jack, so I was wondering if there is any way to get to the cpa without a jack? I'd rather not have it towed to another shop.
Also, my coil pack has a huge crack in it. Could that be causing my problem? And my sai has some really frayed wires and I'd rather not replace it if I don't have to because these repairs are really adding up, but could that be causing problems too? it's not causing gas mileage issues and I live in an emissions-free county, so simply not allowing me to pass emissions isn't a problem.
After heavy rain yesterday my 2005 2.7 Santa fe wouldn't start today. Had it towed to nearby dealer. The crankshaft position sensor needs to be replaced. He claims its melted to the block and oil pan needs to be dropped to remove it.
View 5 RepliesI need to replace the crankshaft position sensor. On my 2002 Grand Caravan Sport 3.3liter. Where it is in laymans terms.
Is it better to approach from the underside Or from the hood side? I will know it when I see it but I haven't seen it yet!!
I have a 2001 Chevy Silverado 4.3L that I recently put a new engine in. The new engine will turn over but will not start. I am not getting any spark for some reason. The OBD2 code that keeps coming up says that the crankshaft position sensor is out of circuit. I have put in a new CKP sensor and new electrical connector, new spark plugs and wires, new distributor rotor and new ignition coil and still get the same OBD2 code and it won't start.
View 2 Replies2002 My friend's 2.7L sante fe crankshaft position sensor went bad and I went to replace it. Removed bolt, it was stuck fast, tried to pry out and it broke off leaving the last 1/2 inch stuck in block. Tried drilling a hole in it and using a screw to get it out but no luck. Afraid to keep drilling that I might damage something behind it. How to get it out?
View 9 RepliesI got a 2004 Nissan Sentra and a p0335 (Crankshaft Position Sensor) popped up on it after the car stalled out sitting in a parked position for 2 mins. The car also stalled out again 20 mins later while I was driving. When the car stalled out in park I had to wait 3 mins because it was just cranking over, when it stalled while driving it started 30 secs later with 1st turn of the key. This car has been having start up issues after the car been driven and sat for 40 mins but when the key is cycled 3 times it starts up fine. I also was going to eventually make a post of this, the car been making clicking or rattling noise at times, off and on mainly when the car been warmed up and at idle more noticeably heard , hear the noise better from inside the car, forgot what side of the engine where the noise is coming from. Also I did a search in the past about recalls on this car and there was a recall on the CRANK ANGLE SENSOR on the 2.5L engines, the car I have is a 1.8L. Stated on this link 3rd one down. [URL] ... . Does it sound like the Crankshaft Position Sensor needs to get replaced?
View 19 RepliesI am having a problem with my 2003 Santa Fe I have taken it to have the check engine light codes read and I have a code for the crankshaft position sensor, random misfires, something with gear 2 and 3 (not sure what it was exactly) it makes a loud noise when in 1st and 2nd gear when I shift out of 2nd the noise gets less and less until its gone and then does not come back until the car sits for a little while and cools down. Its running rough and does not have any power when accelerating. I had the timing belt changed a few weeks ago and it started running funny shortly after. I don't think the guy that did the timing belt knew what he was doing because I had to have someone go behind him and tighten the pulley.
View 3 RepliesMy wife's 2003 Altima has been stalling. The MIL came on P0335 Crankshaft Position Sensor Circuit. I did a little research and it seems that it is pretty common for that sensor to go bad, so I bought a new one. The problem is I can't get the wires off the old one. It is in such a ridiculous place. There is no line of sight anywhere. It has to be done completely by feel. Supposedly, I should be able to push the button until it clicks and then remove the connector. When I push the button, it definitely clicks - but it doesn't stay clicked. It clicks right back out before I can pull on the connector. How can I keep that button clicked in when I can't see anything and I can just barely get one hand down in there?
View 19 Replies33k Civic 2001 "PO335 Crankshaft Position Sensor A circuit" error code
My Civic 2001 LX (non vtec 1.7) threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining.
My Civic 2001 LX (non vtec 1.7) 33k threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining. So much for a reliable honda.
My wife has a 2007 Jeep Compass. The stock stereo stopped working one day. It had no power going to it. My wife's father is a mechanic at a car dealership. He's an older gentleman and isn't very savvy when it comes to modern electronics such as stereos. He tried to fix it for her. He ended up telling her the stereo was "burnt out" and she needed a new one. She was bummed out because the stereo didn't work. I bought her a new aftermarket stereo for her birthday and it came with the installation kit and the adapters and connectors. She asked her father if he could install it for her. He tried and couldn't get it to work. One of his coworkers looked at it and said he suspects there is a "bad wire" somewhere, possibly under the gear shifter? He bench-tested the original stereo and it still works! Where do we look for the "bad wire" ? How do we find it? They haven't been able to find it so far. This model does not have steering wheel controls for the stereo.
View 6 RepliesThis has been an ongoing issue for months. I fill up the Compass's gas tank all the way and, at the next stop light or paused traffic, it will stall. My workaround is to fill the gas tank almost all the way full and it doesn't stall. But, what could be causing this issue? I've seen repair suggestions for things such as power control module valve and connector switch for fuel pump, but haven't seen anything definitive.
View 7 RepliesMy hight beam went off and doesn't work anymore ..my fuse box is the problem and i dont want to replace it cuz its too expensive maybe a chip inside not work right and in my car when i switch the gear to d the hight beam turns on On 6 volts day and night . Now its doesn't work ether the 6 or 12 volts .. How to fix it?
View 2 RepliesI have a 2007 automatic jeep compass that is stalling. heres the thing, it only stalls when i am idle at a red light/stop sign. I also noticed it only stalls when its in drive. if i switch the car to neutral while stopped/idle it will not stall. i also notice this happens more frequently in the rain.
View 6 RepliesI had to break suddenly last night, and my phone (attached to the AUX cable at the time) bounced up under the wheel, gaining access by the accelerator and break pedals. I can hear it vibrate, but cannot feel the vibrations or touch the phone by reaching up under there - and I am worried I will disconnect the wires if I continue to rummage.
I removed the base of the steering wheel column, but did not find my phone, I guess it is wedged too far into the workings of my car Jeep Compass 2007.
I have two questions. could I remove the plastic facing by the windshield without dismantling the car (I can't tell from the manual)
is it safe to drive with my phone in this position? I'm worried it might disconnect the break fluid or something as I try to drive it to the mechanic.
Where the Crank Shaft Position sensor is located on a 2004 4.2 phaeton... Dealership want 360 to install it ...
View 14 RepliesWhere does the CPS located on my truck? Knowing mine is 5.4 L 2000 model. 121,000 miles on clock.
View 6 Replies