Mazda - Protege :: 2000 - Wheezing Kind Of Noise When Accelerating


Mar 18, 2011

My car just started making a wheezing kind of noise when accelerating. Reminds me of wind being forced through a small hole, or the sound of a balloon being aired up.

View 9 Replies

Advertisement

Mazda - Protege :: 2000 - Humming Noise Coming From Passenger Side / Replace Water Pump?

I recently noticed a humming noise coming from the passenger side on my Mazda Protege 2000 ES . I suspected it was the water pump, so I took the car to my mechanic. He inspected the coolant reservoir and it was empty. He also checked the noise and the area were the pump is, and told me that the water pump had to be replaced.

My dad told me that his 1994 Sentra had the water pump replaced but none of these things had to be done and that it was unnecessary. But then I thought, every car is different.

I was in shock with how much the repair would cost, so he then gave me another quote with just the timing belt and water pump replacement for $503, but this time he said that he will not give me any warranty for the repairs because of the tensioner.

View 19 Replies

Mazda - Protege - Smells - Sparkplugs :: 1990 - Rough Idle Stutter While Accelerating?

1990 Mazda Protege with a 1.8L DOHC, manual 5-spd transmission, ~173K miles on it. On my way home the other day, the car ABRUPTLY started to run very rough - with what I would call repetitive and incessant stuttering when accelerating (though I am by no means technical with respect to cars). I shut the car down, hoped the problem would go away, but when I started it up later that day, the problem was still there - the car BOTH idles rough and doesn't accelerate very smoothy. When I come to a stop, the car feels as if it's going to stall but stays running. This afternoon, I took it out on the road for ~3 mile drive (up to ~ 50 mph) and the problem is the same - but I did also notice, when driving, that the car gave off a smell reminiscent of firecrackers - perhaps a sulfur-ish smell. I googled the issues I was having and I got a whole array of problems - ranging from simply bad spark plug wires (which have been replaced in the past 1.5 years) to a stuck EGR valve .

Here's some additional info on my car: -Was just in the shop 2wks ago for overheating - found the thermostat to be bad - they replaced it and I no longer have the overheating issue. While there, they also replaced the belts for the alternator and water pump (Which had been squealing for quite some time) -Spark plug wires and distributor cap were both replaced in the last 1.5 years -Last oil change was > 6 months (but less than 3000 miles) ago - all the fluid levels seem to be fine -Though I think it is unrelated, the car is also making a high pitched squeaking noise emanating from the R front of the car while driving - I suspect this is the suspension-related as the shop informed me that I have one front stablizer link broken while the other is loose (and when I push down on the R-front side of car while it is not running it yields a similar squeaking noise.

View 1 Replies

Mazda - Protege :: 2000 - Idle Roughly - CEL Comes On?

I have a 2000 Mazda Protege ES (1.8L) with 120k+ miles and an automatic transmission. The car drives well at speed, but when sitting at stops it will shake a little, sometimes worse than others. Often the RPMs drop to below the lowest tick for a split second before recovering, very much like when driving a manual transmission and not pressing the clutch in enough. Even when the RPMs are steady at a stop, it shakes enough to rattle a couple of the plastic parts in the dashboard.

Recent history (some likely unrelated, but I'm no expert):New air hose (one from the air filter to the engine) in September. RPMs were falling at idle more often than they are now, there was a decent sized crack in the hose. RPMs stopped falling as often, but has idled roughly before and after.New radiator and thermostat in April (overheated on the interstate and cracked open).New spark plugs and wires last fall after one cylinder wasn't firing.For the last couple years every fall when it starts to get cold, the alternator belt squeaks and I tighten the bolt a little each morning until it stops (usually after 2 days, maybe 3 - the alternator itself is on a long bolt that adjusts the belt tension).Every 5k miles I have the oil changed with high mileage oil and tires rotated/balanced.

I took it to a garage a couple weekends ago after the check engine light had come on earlier in the week. I reset the computer and the light never came back on, so I lost the chance to have the code read, but there weren't any other symptoms beyond what I'm used to. The mechanics at the shop said they couldn't find anything specific causing the rough idle and suggested replacing some or all of the motor mounts, which are weak. They didn't seem confident that would fix the problem, and neither am I, as I don't see how weak motor mounts would explain the low RPMs as well as the shaking.

View 3 Replies

Mazda - Protege :: 2000 Won't Start / Burned Rubber Smell

I think I broke my car. I just bought this car a few months ago and all seemed well. I bought new tires, changed the oil, had the brakes inspected, you know the things daddy's tell their daughters to always be sure of. I have had no problems with the car till last weekend. My boyfriend and I got into an argument, long story short I sped off, using his words "hot rod style".

I smelt burned rubber (not so new tires anymore) but I figured it was just that. When I got back home my boyfriend said that he smelt something burning under the hood. No smoke or fire just a burning odor. The next morning my car wouldn't start. We jumped it and it ran just fine. Did the errands for the day no problem.The next morning it wouldn't turn on again, this time when we jumped it, it just wouldn't start. I have checked the battery at AutoZone and they said it was fine. the fuses are all good as well.

View 11 Replies

Mazda - Sparkplugs :: 2000 Protege Won't Start After Timing Belt Change

2000 Mazda Protege 1.6l Just replaced timing belt, tensioner, idler, water pump, plugs and coil packs

I have checked the timing about 10 times before puting everything back together by rotating the engin clockwise. No stiff point and marks lining up perfectly every time.

Though when I turn the key in the ignition, the engine cranks but doesn't start.

Can't really check the sparks cause I am on my own, but seems like the spark plugs in 1 and 3 are wet with fuel and 2 and 4 are dry.

View 8 Replies

Mazda - Protege :: 2000 - Won't Start / Sometimes Sputters And Lopes Before Just Stops Firing

I have a 2000 Mazda Protege LX with 38k miles on it and a 1.6L engine and it starts fine in the morning to go to work and starts fine in the afternoon to go home from work. If I get home and change clothes, hop in the car to go somewhere, it won't start, turns over like it's out of gas, sometimes sputters and lopes before it just stops firing. It seems to only do this in the afternoon, specifically between 3pm and 5pm, never after dark or in the morning. I can drive all day long as long as I don't cut off the engine.

After sitting for about fifteen to thirty minutes, it will start like nothing ever happened. So far, it only does it once per day. After I get it started in the afternoon, I can seem to go anywhere, stop as many times as needed, and it keeps starting every time. It seems to be getting more frequent as the weather warms, never did it in January or February, but so far has done it every time I try to start it when the temp is around 80 or higher. I get no engine light, temp gauge is normal.

View 1 Replies

Mazda - Protege :: Loud Tire Noise Between 20 And 40 Mph

I read here that some tire noise can be caused by bad belts. How do you know if the tire belt is bad? My tires get loud between 20 and 40 mph. Mechanic says the tires are OK but to replace them to get rid of the noise.

View 7 Replies

Mazda - Protege :: 2002 - Grinding Noise At 3200 Rpm In Every Gear

I have a 2002 Mazda Protege5 and recently it will make a grinding noise at 3,200 rpm (in every gear). It sounds like you touched the side of a rotating drill on a piece of metal or something like that. The mechanic said it was my clutch but my clutch isn't showing any of the tail tail signs of it needing to be replaced and frankly I don't trust the guy. Will replacing the clutch fix this noise? Could it be something completely unrelated to my clutch?

View 2 Replies

Mazda - Protege :: 2002 Engine Overheating / Rattling Noise Behind The Dash

I drive a 2002 Mazda Protege and it's been great to me until this past weekend. I had a 4.5-5 hour trip ahead of me and Google Maps told me a more direct route (i.e. not using the interstates) would save time. It must have erroneously assumed that the highway comprising basically the entire trip would be speed limit 55-65 the entire way. Instead, I found myself slowing down to stoplights and stop signs in small villages between 15-minute sprints. At some point, the interior heat stops - the air being pulled in from outside is not being warmed at all, no matter what settings I fiddle with. Not long thereafter I notice a rattling noise behind the dash. From inside the car it sounds almost like an animal skittering around in the chassis - irregular, short and clipped. With the hood up and an ear to the engine, it sounds like a piece of plastic fluttering in the wind, but with a faint electric "crackling" quality. Soon thereafter the check-engine light illuminates.

Before long the engine overheats and I pull over to the side of the road. Nothing appears to be leaking, and the crackling sound is the only thing noticable. Being in the middle of nowhere, I jumped back in and proceeded to drive at about 35-40, which was warm on the engine but enough to get me to a small town. At this point I checked the coolant reservoir and it was empty. Bought some from Wal-mart, poured it in, and headed out. Things looked fine at first since the engine had sat cold while I was running errands, but pretty soon it was overheating again at speeds as low as 30mph. After getting it towed to my destination, I took it to a garage the next morning. They couldn't find anything wrong with it, and indeed when I drove it back to the hotel that morning the engine behaved normally, the check-engine light was off, and the interior heating was functioning properly.

The next morning, when it was time to depart (but again after an entire night of sitting in the cold), a 20 minute drive to breakfast was smooth as before. Thinking that the mechanic had either waved a magic wand or I'd gotten extremely lucky, I hit the highway and did 65 for a good 20 minutes until the engine began to overheat again. Slowing down to 45 bought a few more minutes to find an exit, but eventually I had to pull over. Popping the hood, I notice the coolant in the reservoir is bubbling to the top! Thinking the mechanic might have added more and overfilled it, I cursed him in absentia. After a good fifteen minutes of cooling off, the coolant settled and in fact drained the reservoir entirely; I refilled it to the line and, again being in rural snowtopia with few options, decided to hit the road again. Not wanting to tempt fate, I stuck to 55mph and the car ran fine for an hour and a half (with the interior heat blasting, per a friend's advice). I stopped once to check the coolant and all was as it should have been - just below the line I'd filled it to earlier. Closer to a city, I decided to experiment again and took the speed up to 60mph.

This was great for 20-30 minutes but eventually the engine began overheating ever-so-slowly and I had to pull over, let it cool off, and replace another full reservoir's worth of coolant that had disappeared before I kept going. I drove the rest of the way home going no faster than 55mph and stopping on occasion to check the coolant. It overheated once even while doing 55mph, but a 15 minute break + coolant refill bought it the rest of the trip. In summary: Although not 100% correlated, going faster than 55mph seems to trigger the engine overheating, at which point the rattling noise appears and the coolant begins to bubble its way back up the reservoir (like it's boiling?!). I'm not sure how the coolant is disappearing because I'm unable to find any leak, nor is there any extra exhaust that would suggest it's burning.

View 10 Replies

Mazda - Protege :: 2002 - Mystery Noise Sounds Like A Creaking Or Bumping In Front End

I drive a 2002 Protege5 with about 125K miles. The suspension (struts and mounts) and brakes have been recently replaced and, with the arising of the Mystery Noise, checked by a mechanic as of last week. The noise sounds like a creaking or bumping in the front end of the vehicle, and comes primarily when slowing to a stop, when the brakes are applied or not. The pace slows as you stop. And it is not always predictable: the mechanic could not recreate the noise, but my wife and I hear it all the time.

I'm just speculating, but should we be looking at the bearings, axles, CV joints... or is this going to get even more expensive? What should I ask the mechanic to look at on this thing?

View 4 Replies

Mazda - Protege :: 2001 - Stuck Gas Pedal / Making Noise When Pushed Harder

Lately, when first starting my car and after it’s been sitting for a while the gas pedal seems to be stuck.

When I push on it slightly it doesn’t move; but if I push a little harder it will make a noise and become free and movable. No further problems until it sits for a while or the next morning. Then the same stuck pedal. Exert a little pressure and it frees up.

I tried squirting WD40 on the linkage but it does no good. What could cause it to bind up? 2001 Mazda Protege LX 2.0 ....

View 12 Replies

Mazda :: 2002 Protege 5 - Hesitation At 3k Rpm

Have 2002 mazda protege 5 . During acceleration at 3000 rpm the engine hesitates. Computer said o2 sensor, replaced it but that wasn't it. Drilled out both catalytic, that wasn't it. Found hole in mass air flow tube, figured that is it. I haven't replaced that yet, however I used gorilla tape thinking it would be a temporary fix but that didn't work. I know I need to replace that tube, but think that it may now be a fuel pump issue??

View 5 Replies

Mazda - Protege :: 1999 - Won't Start When Hot

I have a 1999 Mazda Protege. As of last summer it started giving me problems with not wanting to start after I had driven it around town for a little while. (IE: to the grocery store, to the bank and then to my sister's house. It wouldn't give me the same problem if I just went to the grocery store and back home. It would start up fine and I'd be on my way. Only when I went somewhere and shut it off then repeated that a couple more times.) I took it to a mechanic who wholeheartedly believed it was the coil packs not allowing my car to function properly.

So we replaced those and everything seemed on the up and up. (Keep in mind that this was towards the end of summer and the temperature was dropping.) The car was perfect all throughout the fall and winter, but now that the temperature outside is starting to rise again it's beginning to do the same thing it did last summer. I don't want to take it to another mechanic that's going to have me dish out an extravagant amount of money again only for the problem to persist.

View 5 Replies

Mazda - Mazda3 :: Loud Noise When AC Is On And Accelerating

I have a 2004 Mazda 3. I just had it inspected and cabin air filter replaced. Now, my car makes a loud noise when the a/c is on and I'm accelerating. The noise sounds like a fan is vibrating /something is blocking it or like a motor is rev-ing that shouldn't be. There definitely is something wrong that wasn't there before the filter/s replaced. I watched a Youtube video on it... a real pain to replace them, but it looked like the fithad to be pretty tight... Could the filters have been installed incorrectly or some part not put back together correctly?

View 2 Replies

Mazda :: Protege ES 1.8L - Rattling And Knocking Front End

2000 Mazda Protege ES 1.8L

What's a good way to find whats the cause of all the rattling and knocking in the front end of my car when going over uneven terrain? It seems that noise appears only if one of the wheels is lifted up a little bit. I am attaching a picture describing the "motion" here:

Steering wheel doesn't shake when driving at high speeds and is fairly stiff, but it does pull to the right a bit, maybe because I didn't perform a front end alignment (I know this is not good) after I had most of the stuff in the suspension of the replaced; all 4 struts + boots + mounting blocks, ball joints, control arms...

Now the only part, I didn't replace was the sway bar link on the passenger side and it's being knocking for 3 years. The one on the driver side was replaced at the time the struts were replaced but I didn't have enough money to pay for the other one.

Another mechanic told me when I was quoting that sway bar links aren't really necessary as a safety feature, and a google search showed me that there are people that just take the sway bar off the car, so I left it there and just tried to live with the noise. now I am noticing the driver side is knocking as well, and I am wondering if it has to do with because I didn't replace the one in the passenger side?

I just want to rule out the possibility of another component being the cause of the noise because I am prioritizing safety over ride comfort in my attempts to save some money.

View 5 Replies

Mazda - Protege :: 1996 - A/C Isn't Blowing Cold Air

it was over 100 degrees today in Lawrence, Kansas and on the way home from work, the air conditioner stopped making cool air. Hot air now comes out. This is a different problem that the poster before me seems to have. Mazda Protégé, 1996, 128,000 plus miles on it.

A reconditioned one was installed in 2006, compressor replaced in July, 2012.

View 6 Replies

Mazda - Protege :: Brakes Stuck And Burning Up

Basically, my car (2002 Mazda Protege) has been acting like my brakes are engaged. Not all the time, though - The first time I get out and drive it, it drives smooth as silk like always. But then after I put it in park and then get back in and head out (I'm a delivery driver, so this is constant), sometimes it feels like the brakes are constantly being pressed. No, the emergency brake is not on. Most of the time it's almost not even noticeable so, like an idiot, I put it off for the past week. But today, it was very, very, very bad. I was having to press the gas to the floor to get up to speed, and then it was constantly trying to slow down. My brakes were definitely getting burned up while it was doing this, but luckily it stopped.

It may be unrelated - I know I have an oil leak, but today I saw a very unusual spot where something leaked out in my driveway. I checked my oil, and it was where I expected it to be, but this was a relatively large stain which would be very unlike my current leak.

View 6 Replies

Mazda - Protege :: Little Hesitation And Jerkiness During Acceleration

Started my car yesterday and as I was accelerating, it made a very loud noise. It sounds like normal engine acceleration noise, only ten times louder. It was present whenever I accelerated, but not when I was coasting or idling, and not when the car was in neutral. (It's a stick shift.) During acceleration, there was a little hesitation and a little jerkiness, but not horrible. The problem came on suddenly - no problems with the car before yesterday.

View 4 Replies

Mazda - Protege :: Generator Or Alternator Same Thing?

My Mazda 1996 Protege appears to have no alternator, but there is something called a generator. Are they the same thing?

View 19 Replies

Mazda - Protege :: Dashboard Lights Cutting Out

Here's a quandary for those who know more than I do:

I have a 2000 Mazda Protege with 182,000 miles on it. On occasion my dashboard lights (and radio, for that matter) cut out, going completely dark. Now here's the kicker: If I give the dashboard a little tap with my hand, everything comes back all glowing and lit.

My fear had been the alternator was going bad (Again!), but since it seems to be coming back with a bop on the dashboard...is this just a loose ground? What should I be looking for? Is this something a novice like myself could be taking care of, or where should I be directing my mechanic?

View 5 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved