Mazda - Protege :: 2003 - Stalls At Start Up When Warm Up?
Jan 25, 2013
I have a 2003 Mazdaspeed Protege that is having a stalling problem. The motor has about 30k miles on the block with around 3k miles on the internal components (rods, pistons, cams, etc.). Cylinders were bored 20 over and head was machined.
This stalling, or almost stalling, problem occurs when I start the car after it's been warm for awhile. For example, if I were to drive for an hour, park it for 45 minutes, and then come back out to start it up. It'll fire up, drop to idle, and then the idle will dip, stalling 50% of the time. The rough idle lasts anywhere from 5 to 20 seconds, and then usually fixes itself.
Giving it some gas does nothing to alleviate the problem; sometimes making it worse. Cleaning the idle air control valve solved this for a few days, and then it was back to its old ways. These symptoms do not occur on cold starts or if I restart the car after 5 or 10 minutes of it sitting. We couldn't find any vacuum leaks and there are no codes being displayed.
View 4 Replies
Advertisement
1995 Mazda Protege1.5 LAuto153K miles.
My car was running fine, then one day it started sputtering while driving, mostly when I accelerated. It stalled and I could not get it started. This happened on a day when it was raining hard, but not sure that had anything to do with it. A few days later when I went to pick the car up it started right up, it had stopped raining and been dry for 2 days prior. But about a mile into the drive back home it stalled and I could not get it started.
Here is what I have tested so far.
- Put in new fuel filter.
- Tested the fuel pressure and pressure regulator
- Tested the injectors with a noid light.
- Tested that the spark plugs were producing a spark.
After I pulled the plugs and cleaned and dried them (they were wet with gas) the car started, but I think not because of anything really related to the plugs. What I've noticed is that when cranking the engine if I give it gas it will not start but if I keep off the throttle it will reluctantly start. But once it starts the idle is smooth and as it should be. Then if I give it any gas it immediately stalls. It seems to me given these symptoms that it is getting enough air to idle but not enough air to match the increased gas.
The only CEL code that I'm getting (which I had before this issue occurred) is the "closed throttle position switch" (I forget the number). If it was an MAF, or IAC, or EGR issue would I not get a code? What this could be and how to test it. Again my guess is its an air intake issue but not sure where.
View 11 Replies
The alternator belt recently broke off on my Mazda Protege and by the time I was able to drive it to my local Mazda dealer to have the belt replaced the engine was completely dead. I drove the car about 12 miles after the alternator belt broke. I noticed as I was driving to the dealer that my heater was not working; the fan was working but it would only blow cold air. I know that the alternator belt also controls the water pump, so I tried to keep my engine rpm's below 2000 while driving to avoid overheating the engine. On the way to the dealer the temperature gauge on the dashboard increased to about halfway between cold (C) and (H), which is where it usually sits after the engine warms up.
The belt was replaced, but I have noticed that ever since then the temperature gauge always sits at "C" and the engine never warms up. The heater continues to not produce any warm air. In addition, I have felt the engine with my hand after driving for about 20 minutes, and although it feels warm, it is not nearly as hot as it should be. I suspect that the engine cooling system is continually working for some reason, instead of allowing the engine to warm to its optimal operating temperature and then maintaining the temperature at that level. Because this coincided with my alternator belt breaking, I suspect that the root of the problem is either electrical in nature or associated with the water pump somehow. However, I don't know enough about cars to figure it all out.
View 1 Replies
I have a 1999 Mazda Protege. As of last summer it started giving me problems with not wanting to start after I had driven it around town for a little while. (IE: to the grocery store, to the bank and then to my sister's house. It wouldn't give me the same problem if I just went to the grocery store and back home. It would start up fine and I'd be on my way. Only when I went somewhere and shut it off then repeated that a couple more times.) I took it to a mechanic who wholeheartedly believed it was the coil packs not allowing my car to function properly.
So we replaced those and everything seemed on the up and up. (Keep in mind that this was towards the end of summer and the temperature was dropping.) The car was perfect all throughout the fall and winter, but now that the temperature outside is starting to rise again it's beginning to do the same thing it did last summer. I don't want to take it to another mechanic that's going to have me dish out an extravagant amount of money again only for the problem to persist.
View 5 Replies
I have a 1998 Mazda Protege LX 1.5 L 4 Cylinder and i have been having some starting issues, and stalling at stop lights.
To be clear i have replaced/cleaned, Injectors, Spark Plugs, Spark Plug Wires, Distributor Cap, Distributor Coil, Air Filter, Cleaned MAF, Cleaned the EGR Valve,
My car won't start in the morning, just gives cranks but if I press gas pedal it starts and have to keep it until engine gets hot enough. then it works till the car cools down again, and repeat the problem in the morning when I have to go to work. When the car is warm it starts fine but has idle issues regardless of temperature. As usual when the engine is cold or cool, it won't start.
Visited 2 different mechanic shops and the problem still exist, I don't know how and what they did it, it only worked for couple of months and the engine noise was bit high, I believe he just increased the idle, When i am at stop lights it has a rough idle and tries to die, When it idles it idles rough, Every once in a while I get a CEL Cylinder Misfire on cylinder 4. I'm confused on want to do , Don't know what else to do and its getting tiring, The car also feels like a lack of power.
View 9 Replies
I have a 2003 Mazda Protege. I had the check engine light come on and took it to my local repair shop. They diagnosed it as a bad oxygen sensor. They replaced it, but a week later, the light came back on. So, I decided to take it to the dreaded dealership and pay for their "expertise". They informed me that the light was a result of a intake hose with a hole in it. They also told me that the vehicle's oil pan was rusty and needed to be replaced. The vehicle did not leak oil. After a week of driving, I noticed spots of oil on my driveway. I checked the oil and it was low, so I decided to have it towed back to the dealership to have it checked out. I assumed it was the oil pan that had not been installed properly.
Today, the service tech informed me that my engine was blown and needed to be replaced. He told me that this cam warped and didn't leak before because the pressure was being release through the rusty oil pan. This sounds absurd to me. It seems to me that what has happened is their responsibility. What could have caused this? A co-worker suggested that more than likely the mechanic could have made a mistake and started the engine without motor oil either after the oil pan was replaced or after the vehicle sat overnight and the oil drained out. Does this seem more logical? If the dealership is at fault, but will not fix it, what can I do?
View 19 Replies
I think I broke my car. I just bought this car a few months ago and all seemed well. I bought new tires, changed the oil, had the brakes inspected, you know the things daddy's tell their daughters to always be sure of. I have had no problems with the car till last weekend. My boyfriend and I got into an argument, long story short I sped off, using his words "hot rod style".
I smelt burned rubber (not so new tires anymore) but I figured it was just that. When I got back home my boyfriend said that he smelt something burning under the hood. No smoke or fire just a burning odor. The next morning my car wouldn't start. We jumped it and it ran just fine. Did the errands for the day no problem.The next morning it wouldn't turn on again, this time when we jumped it, it just wouldn't start. I have checked the battery at AutoZone and they said it was fine. the fuses are all good as well.
View 11 Replies
It's a 2002 Mazda Protege... The car shut off once while running in the driveway. Completely: engine, radio, everything. I took the key out and put it back in a couple of times and got nothing, no click, no turning over. Did it one more time, and it started up as if nothing was wrong.
Then again the next morning. Car won't start. I notice all the electronics are working while the key is in the accessories position. They shut off as soon as the key is in On, and nothing when turning to start. Took the key out, waited a minute or so, then tried again and everything worked as if nothing was wrong. I'm guessing this might be the ignition switch?
View 6 Replies
2000 Mazda Protege 1.6l Just replaced timing belt, tensioner, idler, water pump, plugs and coil packs
I have checked the timing about 10 times before puting everything back together by rotating the engin clockwise. No stiff point and marks lining up perfectly every time.
Though when I turn the key in the ignition, the engine cranks but doesn't start.
Can't really check the sparks cause I am on my own, but seems like the spark plugs in 1 and 3 are wet with fuel and 2 and 4 are dry.
View 8 Replies
I have a 2000 Mazda Protege LX with 38k miles on it and a 1.6L engine and it starts fine in the morning to go to work and starts fine in the afternoon to go home from work. If I get home and change clothes, hop in the car to go somewhere, it won't start, turns over like it's out of gas, sometimes sputters and lopes before it just stops firing. It seems to only do this in the afternoon, specifically between 3pm and 5pm, never after dark or in the morning. I can drive all day long as long as I don't cut off the engine.
After sitting for about fifteen to thirty minutes, it will start like nothing ever happened. So far, it only does it once per day. After I get it started in the afternoon, I can seem to go anywhere, stop as many times as needed, and it keeps starting every time. It seems to be getting more frequent as the weather warms, never did it in January or February, but so far has done it every time I try to start it when the temp is around 80 or higher. I get no engine light, temp gauge is normal.
View 1 Replies
Where the camshaft position sensor is on a Mazda Protege5 2003. I can't seem to find any information about this particular car.
View 2 Replies
2003 Mazda protege with 105,000 miles. Have had an intermittent clunking sound from rear for years. Mechanic says rear sway bar is bent. Already replaced bushings because they were bad. Do I need to spend $289 plus labor to replace the sway bar?
View 4 Replies
This issue with my 2003 Mazda Protege 5, manual transmission, has been going on for years. I'd like to sell the car, so I'd like to fix it.
On occasion I am unable to shift into first gear from a stopped position. This never happens in the late fall, winter, or early spring - it all seems to depend on how warm it is outside. It is always fine at the start of the trip, but becomes a problem in what seems like a period of time proportional to how warm it is outside. Again, when its cool outside, it pretty much doesn't happen. But once we pass 25C / 77F it is common, and will almost certainly happen on any trip of over a 10 minutes. The hotter the weather, the faster it shows up as a problem.
If I leave the car and come back after it cools down, first gear works fine again. And I can downshift into first gear as I come to a stop with no issues - I just hate riding the clutch like that, so I've been starting in second gear instead.
View 10 Replies
When I am slowing to a stop, my engine idle gets really low (like 500rpm or less) and sometime stalls. At the same time, the oil light comes on. It does this all the time, and yes I've had my oil changed recently and actually I just checked it the other day and it was fine (along with all other fluids).
I've had the mechanic take a look at this three times and every time something gets fixed but this problem remains. They now say it's a ghost. It is not the air intake (I've had all of the hoses checked and a bad one replaced). It's not the electrical (I've had the spark plugs and cables replaced about a year and a half ago).
I've pretty much had everything that a car of a certain age needs done fixed/replaced in the past year or so, and I still can't figure out what could be causing this. A recent show had a similar problem, but the gal didn't mention the low idle/stalling. In that show they mentioned that she should have the oil pressure gauge checked or replaced, but would that cause the low idle/stalling? I don't know what to do and I'm very reluctant to go to a dealer.
View 19 Replies
Have 2002 mazda protege 5 . During acceleration at 3000 rpm the engine hesitates. Computer said o2 sensor, replaced it but that wasn't it. Drilled out both catalytic, that wasn't it. Found hole in mass air flow tube, figured that is it. I haven't replaced that yet, however I used gorilla tape thinking it would be a temporary fix but that didn't work. I know I need to replace that tube, but think that it may now be a fuel pump issue??
View 5 Replies
2000 Mazda Protege ES 1.8L
What's a good way to find whats the cause of all the rattling and knocking in the front end of my car when going over uneven terrain? It seems that noise appears only if one of the wheels is lifted up a little bit. I am attaching a picture describing the "motion" here:
Steering wheel doesn't shake when driving at high speeds and is fairly stiff, but it does pull to the right a bit, maybe because I didn't perform a front end alignment (I know this is not good) after I had most of the stuff in the suspension of the replaced; all 4 struts + boots + mounting blocks, ball joints, control arms...
Now the only part, I didn't replace was the sway bar link on the passenger side and it's being knocking for 3 years. The one on the driver side was replaced at the time the struts were replaced but I didn't have enough money to pay for the other one.
Another mechanic told me when I was quoting that sway bar links aren't really necessary as a safety feature, and a google search showed me that there are people that just take the sway bar off the car, so I left it there and just tried to live with the noise. now I am noticing the driver side is knocking as well, and I am wondering if it has to do with because I didn't replace the one in the passenger side?
I just want to rule out the possibility of another component being the cause of the noise because I am prioritizing safety over ride comfort in my attempts to save some money.
View 5 Replies
it was over 100 degrees today in Lawrence, Kansas and on the way home from work, the air conditioner stopped making cool air. Hot air now comes out. This is a different problem that the poster before me seems to have. Mazda Protégé, 1996, 128,000 plus miles on it.
A reconditioned one was installed in 2006, compressor replaced in July, 2012.
View 6 Replies
I read here that some tire noise can be caused by bad belts. How do you know if the tire belt is bad? My tires get loud between 20 and 40 mph. Mechanic says the tires are OK but to replace them to get rid of the noise.
View 7 Replies
Basically, my car (2002 Mazda Protege) has been acting like my brakes are engaged. Not all the time, though - The first time I get out and drive it, it drives smooth as silk like always. But then after I put it in park and then get back in and head out (I'm a delivery driver, so this is constant), sometimes it feels like the brakes are constantly being pressed. No, the emergency brake is not on. Most of the time it's almost not even noticeable so, like an idiot, I put it off for the past week. But today, it was very, very, very bad. I was having to press the gas to the floor to get up to speed, and then it was constantly trying to slow down. My brakes were definitely getting burned up while it was doing this, but luckily it stopped.
It may be unrelated - I know I have an oil leak, but today I saw a very unusual spot where something leaked out in my driveway. I checked my oil, and it was where I expected it to be, but this was a relatively large stain which would be very unlike my current leak.
View 6 Replies
Started my car yesterday and as I was accelerating, it made a very loud noise. It sounds like normal engine acceleration noise, only ten times louder. It was present whenever I accelerated, but not when I was coasting or idling, and not when the car was in neutral. (It's a stick shift.) During acceleration, there was a little hesitation and a little jerkiness, but not horrible. The problem came on suddenly - no problems with the car before yesterday.
View 4 Replies
My Mazda 1996 Protege appears to have no alternator, but there is something called a generator. Are they the same thing?
View 19 Replies
