Nissan - Fuses - Altima :: AC Quit Blowing Air / Car Won't Shift Out Of Park
Jun 17, 2013
My wife's AC quit blowing air last week (a '05 Nissan Altima), so I decided to check all the fuses before just replacing the blower motor. I pulled all fuses out in all three fuse boxes and didn't find any blown. Got a call from an upset wife later that day saying she could not shift the car out of park. Currently, she is driving it by using a screwdriver to release the safety switch next to the shifter.
View 3 Replies
Advertisement
My automatic 2007 Nissan Altima has developed an intermittent problem when I go to shift it into park it won't shift down past neutral. I can't physically move the gear shift past neutral and can't take my key out of the car. If I wait awhile or drive off somewhere else it will later allow me to shift normally again and won't happen for awhile. It has happened maybe 8-9 times but I worry it will get worse or break the transmission. I've taken it to a mechanic and they looked at the transmission and didn't see a problem but sense they couldn't recreate the issue they couldn't fix it.
View 1 Replies
92 PA Base
It's that time again for vehicle inspection and my horn has been blowing fuses. I had it diagnosed by the dealership and they stated the horn pad inside the steering wheel is bad. They also stated the horn pads for my model of PA has been discontinued and that I should install an aftermarket horn. If I don't have this horn installed I'll fail the inspection.
View 3 Replies
I did a bad thing last night, I put a jumper in the 20 amp cigar/data link connector and all kinds of things went out, will not shift out of park, no directional, power windows, power mirrors, no brake lights ,no hazards, no wipers, no interior lights and I don't know what ever else is not working.
View 3 Replies
My 2001 altima wont shift to high gear. driving around town seems to be ok, will driving on the highway be dangerous?
View 5 Replies
I have a 13 Altima and have been hearing a clunk/pop sound when coming to a stop and sometimes when changing from park to drive and park to reverse. It seems to also be there when accelerating too and the car is also seem to be vibrating when moving at lower speeds. Today i noticed something else. I parked the car and took the key out. I went to the side of the car and slowly rocked it back and forth and started to hear this clunk sound. I have uploaded it to youtube and can be found here [URL].... . After hearing the sound, I decided to take the driver wheel off and noticed it makes the same sound when i move the tires. It seems to be coming from the CV joint, where it connects to the transmission. why would a car make that clunk sound with the car/key off and swayed back and fourth? does this seem like a CV joint issue or something related to the transmission.
View 3 Replies
My car is a 2008 Nissan Altima 3.5L. It has an automatic cvt transmission. Here's the scenario: I turn my car on and shift into drive. I'll drive for maybe 10 feet and I will hear this strange sound that can only be described as a dull knocking followed by a dull scraping sound. The dull scraping sound will last for about 5 seconds. The sound appears to originate from behind the gas pedal, and I'm think I can feel the gas pedal vibrating very slightly as it is happening. The only condition that makes this sound happen is when I shift from park or reverse into drive. If I start my car and put it in drive it happens. If I'm at a red light go to park then drive, it happens. If I turn my car on, go in reverse, then drive, it happens. However it doesn't happen if I just stop and don't change the gear selector. It's been happening since I bought the car at 56k miles, I'm at 69k now. I haven't seen any decrease in performance, the car runs like a champ.
View 6 Replies
I have a 1997 Nissan Altima that I just barely got and it has started to show signs of trouble.
Sometimes when I put the vehicle into drive and step on the gas the car will not move and instead the engine will rev.I'll put the car back into park and then into drive and it'll work fine.
I checked the ATF, which was incredibly low and refilled it. The engine oil was also very low, which was refilled. The problem still persists. So I decided to add a bottle of Fuel Injector Cleaner to the gas tank.
I took the car for a short drive and nothing happened aside from the fact that the Check Engine light now comes on and off. The car also idles between 1000-1500 rpms.
View 19 Replies
This fuse controls the interior lights, power windows, and the brake pedal shifter release. I noticed the problem when the vehicle would not shift out of park.
I replaced #15 fuse (5amp) and everything worked fine however several hours later with the vehicle simply parked the fuse blew again.
Appears to be a "short" of some kind but it seems to take several hours for the fuse to blow.
View 5 Replies
I have a 2001 Olds Alero. The AC compressor went out so my father in law and I replaced it. It worked fine for about one month, not it keeps blowing the a 10 amp fuse (can't remember which one at this moment, my wife is at the store with the car). I have been told that it is a bad wire, I can't see any pinche wires and have looked up to where the wires go into the tape/plastic casing. I have also been told that it is the compressor that is doing it (the parts store said this was not the case... I think they just don't wanna warranty anything).
View 12 Replies
So I just got a new Passport Radar for the car and noticed that im getting no power...Checked the fuse box and and fuse was blown...replace it and the fuse blows automatically.
View 6 Replies
So I installed my XS HID low beams and fogs a couple of weeks ago, and everything was working fantastic. However, when I installed my LED turns and load resistors, whenever I turn on the low beams, the inline 30A fuse pops. The HID fogs continue to work. The switchback turns work great, and I have never got any hyperflashing.
I have checked all the connections, and they all seem strong. I have used the diagram I found on here from exLEDshop outlining all the connections on the pin array for the headlight harness. I am tapped into the blue wire on the driver's side for + turn and the black for -, and the black w/orange stripe on the passenger side for + turn, and the black for -. If I accidentally have the load resistors connected to the wrong wire, would the turns hyperflash?
I know that it would be better if I used grounding points on the chassis for the load resistors, but could this be causing the short? Or could bad ballasts that are the culprit? The only reason I'm leaning away from it being the ballasts is because they worked fine until I put the load resistors in.
View 23 Replies
I just got my led switch back lights in for my 08 camry. But I have run into a problem I have installed all four led signal lights (switch backs in the front and led ambers in the back) and the led flash relay for my car. What is happening is that the led will turn on for a couple of seconds and then the fuse for the signal lights burns out both the one under the dash and the one under the hood.
View 3 Replies
I've blown my turn signal fuse for 3 times until the relay burned out. Now I have had cleaned turn signal switch (with CC) from all of the old stuff in there and replaced hazard switch. But it happens again! After 5 minutes driving, both fuses (7,5 AMP for turn signals and 15 AMP hazard) blown out. I'm afraid there are some shorts in wirings.
I'm looking for the wiring diagrams or any other users experience in this matter... Where shall I start from?
There was a water leakage behind and under drivers seat. I removed trims etc. to lift the carpet to take the Comfort Module for checking as there were some weird thing in overall car electric systems (central locking, saloon lightnings, electric windows and dropping gauges on instrument panel. I found a small amount of water in container, where the module is placed, but on the electric parts weren't any water marks... Also it's impossible to connect to the CCM via vag-com.
View 3 Replies
Several weeks ago, my wife drove our Outback for 10 minutes, turned the car off, then turned it back on after 10 minutes. After 15 minutes of its being on the second time and the car being in a car line, the red temperature indicator blinked, then went solid. She pulled over to let it cool, then put coolant in the overflow reservoir when she got home. The reservoir was nearly empty. The very next day, the exact same thing happened, in the exact same sequence - 10 minutes on, 10 off, 15 minutes on in a car line, then indicator came on again.
I took it to a mechanic who could not reproduce the issue after letting it run for four hours. He replaced the fuses and told us to bring him the car when the problem recurred. Reservoir tank is full, no blockage in line from radiator to overflow tank.
The next day, for a third time, the car overheated in the pickup line. We brought it in the following day. The mechanic finally was able to reproduce the issue. He said that both fans (a subi outback has two) needed to be replaced, as they were drawing a tremendous amount. He advised that I take it to subaru to find out if there was anything they could do re: warranty.
I took it to subaru, who said that the fans are not now under warranty (we have 65k on the car). I decided to have them replace the fans anyway, so I asked them for a diagnosis. However, after two days in the shop, they were unable to reproduce the problem. They ran the car in idle, they tried to recreate the stop-and-go/standstill environment of a carline, but no luck. They said that the fans were drawing the expected amount and that they would need recreate in order to diagnose.
I have two questions:
1) Should I replace the fans myself? I can either take the car back to the first mechanic and have him replace the fans or I can do it myself. I can do basic jobs like oil changes, replacing serpentine belts, but I'm not sure what nuances are involved with replacing anything electrical.
2) Most importantly: What would cause both fans in a relatively young subi to spike their amperage draw intermittently? I guess it's possible that i just got two bad fans, but that doesn't seem to be a common problem with this model. So, I want to make sure that this issue is not indicative of some other underlying problem.
View 2 Replies
Suddenly my 2007 Sonata Limited trunk and gas lid fuse keeps blowing.
I'm not an electrical guy so I don't know how to check with a meter, I oiled the latches. My car was rear ended near the tank lid/bumper area a few years ago, but everything worked fine til recently.
I can replace the fuse, but after a few uses it will blow, sometimes it will blow without being used. I can't tell if it's the trunk or gas lid causing the problem because nothing will happen immediately, Basically I am only finding out my fuse blew when I need to use it.
Where I could look to inspect the wiring for kinks or it's connection run?
View 7 Replies
About 11pm 2 nights ago on our way to Florida, hit a nasty bump on I-95 in SC and there went the fuse to the tail lights and dash lights (#17 I believe). Obviously something shook loose from the jarring of that bump and blew the fuse. I've blown this fuse before, but I thought it was due to a cracked LR tail light assembly holding water, which was replaced last weekend.
Now I replace the fuse, and as soon as I hit the headlight switch...it blows again. Holding my breath running around FL at night until the man pulls me over for no tail lights. So far, here's what work has been done:
- Replaced entire LR tail light assembly with new one, new bulbs, new bulb plugs - Sprayed electrical cleaner all over harness plugs, and used electrical grease to hook it back up
- Sprayed electrical cleaner into both trailer plugs
- Did replace both batteries last weekend - noticed on the drivers side battery appears to be some relays next to the battery on the fenders - one appeared to be beat up probably due to prior battery replacements - no clue what they do
I am at a total loss. Worse fear is I can't figure this out and I have to turn it over to the dealership
View 7 Replies
Why the rear Auxiliary A/C blower on a 2004 Sport Trac keeps blowing fuses and how to fix it?
View 12 Replies
4 days ago, my '04 Chevy Aveo (89,300 miles) would not shift out of park and no brake lights were coming on. I had to use the shift lock release to start the car in neutral, and I took it to dealer. Dealer replaced the brake switch. One day later, the problem returned. I took back to dealer, and they showed me that the light blue "15" stop fuse (the right column of fuses, second one down) had blown. They replaced. It again worked for a day, and the problem came back. Each time I put a new 15 fuse in now, it works temporarily, but now fries either immediately or within an hour. In order to drive, I still have to use the shift lock release, which isn't great, because it means I have to drive without brake lights.
View 10 Replies
Replaced battery, replaced fuse line holder by battery, checked starter w/ jumper wires, most smaller ignition related fuses are fine.Can't read the schematic for the relay box, so I didn't check that. online manufacturer manual has nothing on it. how do I test those?
View 13 Replies
Having an issue with my car blowing fuel pump fuses every once in a while under heavy to moderate acceleration. Have replaced inline fuel filter and the fuel pump resister(white ceramic part). Runs fine with normal driving, but when I want to get some horses out of it, it will cut out and stall and once i replace blown fuse it will start back up again, and I'm off and running again.
View 2 Replies
