Oldsmobile - Intrigue :: 2001 - Replaced Throttle Position Sensor Overheating?
Mar 14, 2013
my old lady has a 2001 olds intrigue with the 3.5L in it. Sunday evening we replaced the Throttle Position Sensor and the Coolant Temp Sensor. Monday she was on her way back to Iowa and the tempature gauge spiked up to the Hot area. I looked it over and could not find anything wrong. I sent her on her way and she made it about a mile before it did it again. The car will spike up to the hot area but the motor shows no signs of over heating. I checked the temps with a heat gun while the car is idling and read out Thermostat housing-160, Rad-80, Rad hose-130, and coolant 170. I than ran the car up so it shows on the gauge its hot and than checked again, it than reads Thermostat housing-172, Rad-100, Rad hose-134, and coolant 184. If I am running it at 1500 rpms it will spike up but once i take it up to 2500 rpms it drops back down to normal on the gauge. I am lost for what it could be.
View 19 Replies
Advertisement
2004 2.4L 4cylinder manual transmission. I had a knock sensor code and replaced it. Then I had a code for the TPS and I replaced it with the new part today and after replacement the vehicle idles at 2000 RPM. what should I change?
View 5 Replies
SO, my Buick has given the code for bad TPS, and it was replaced a little over a year ago...and now after the same symptoms, replaced again.. However, this time, right after replacing, it gave the code again, and still stalls out /doesn't want to stay running especially when put in gear. My regular mechanic also recently just put on a new catalytic converter and a new fuel pump and fuel filter. I'm at a loss, and desperately need my car back.
A little back history...about 3 years ago a 'friend' was to work on my car to install the thermostat and power washed the engine...which shortly after started having all kinds of electrical issues. Right after that, my mechanic had to install a coil, spark plugs, new ignition panel and the 1st tps.
View 8 Replies
My 2000 Oldsmobile Intrigue keeps overheating when driving over the mountainous area outside of town. It usually occurs when coming back from drill (4 hour drive). The mountainous region is around the 3.5 hour mark. All the fluids are normal. Coolant is within the preferred region and oil is the same. But every time I climb the mountain it reaches to the overheat mark and I have to kick on the heater to save the engine. Is there another reason behind why it over heats?
View 2 Replies
So I have a 2000 Oldsmobile Intrigue with about 190k miles. It currently has an overheating problem but first I'll discuss some history:
-It had a previous overheating problem a few months ago that was accompanied by bubbling sounds. We diagnosed this as boiling coolant because the system was not pressurizing due to a leak in the reservoir. We fixed the reservoir leak and pressure tested it to find that the leak was repaired. The bubbling noises stopped and the car no longer overheated.
-The car was then underheating nearly all the time. We diagnosed this as a broken thermostat, probably killed by the overheating that was caused by the leak in the reservoir. We replaced the thermostat and bled/burped the system and now the car does not underheat.
Now the car operates around the half-temp mark and stays very regular except in traffic or parked in the driveway. So it overheats when it is idling. You can rev up the engine in these cases and see the temp gauge fall back down, so it is dependent on RPM only and not on the actual traveling speed of the car. Also at this time the car supplies nice heat to the cabin.
Things to exclude:The electric fans seem to be working fine and they switch on and off supplying a good deal of wind.The system was bled/burped.The system has a new thermostat.The system does not leak based on a pressure test.The system has enough coolant.The system supplies good heat to the cabin.
My guess is that there is a clog/general grossness inside the system someplace or that the water pump is starting to fail?
View 19 Replies
We bought a 2006 Hyundai Sante Fe with the 3.5L and 4 wheel drive about two months ago, it has 94,000 miles on it. It was purchased from a dealership, and they had to work on it for a month before we took it from them because of some lights that were on, resulting in some sensors being replaced. We had it about a month when we took it to the grocery store, when we came back out I started it and it made a terrible noise, but was running, I immediately turned it off. Upon further inspection, the main serpentine belt had snapped, causing some damage to the secondary belt. We towed it home and I began to fix the belts.
When I pulled off the passenger side wheel and access cover, I noticed the remains of the belt were stuck behind the harmonic balancer, I tugged on it with about 5 pounds of force, and the entire pulley fell off of the harmonic balancer. I'm not sure if the belt stacked up behind and pushed it off, or if it just went bad, but the rubber between the portion that connects to the crank and the pulley was ripped, and missing in some spots. I replaced the harmonic balancer, and both belts, good to go, everything is running fine.
About a week later, the TCS etc. lights came on, but no check engine. I researched it a bit and came up with three possibilities:
1. Fuse
2. Tone wheel cracked/broken
3. Crankshaft position sensor
I checked the fuses and nothing was burnt, I never lifted the truck up to check the tone wheels.
View 5 Replies
I have searched and have not found any information on replacing the throttle position sensor. My Santa Fe was running normal. I changed my tp sensor and how it limps along. When I loosened the old TPS, not even removed it, I heard a noise inside the TPS. When I replaced it I adjusted the TPS to read between 9 and 10% on my reader. But when I push on the gas pedal with the key on position the percentage doesn't move. Also when I drive it now it limps along and does not accelerate.
View 2 Replies
Getting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.
If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?
View 8 Replies
I just posted last week that my check engine light was on and the dealer wanted to replace fuel injectors. But after the fuel throttle was cleaned and oxygen sensor was replaced the check engine light went off. However, yesterday the check engine light came back on. I am talking it back to the dealer, in a couple of days. Where can I go to get to get the error codes read so I have them before I go back to the dealer? Around 128,000 runs fine, around 40 miles per gallon. Last time I had the oil change dealer nothing came up on the 30 point inspection.
View 7 Replies
how hard is it to install a bcm in a 01 Oldsmobile Intrigue, and what all will it take care of in a car? I know its a sm computer that does alot of operations for a car,but would that cover everything with the security light on??
View 1 Replies
I recently had my power window motor replaced, and my A/C charged, after that my cruise control started going off by its self, when I turned on the turn signal or opened the window, it only happens when the body is warm, not the engine. I had someone say, some of these vehicles have been found to have been built with a pinched wire (or wire harness) where the sunshade pivot arms go through, but I have had this car almost 2 years and it never did this till this work was done on it. What can I check for? It's a 2001 Olds Intrique.
View 2 Replies
I was reading the car's settings using the Torque app and an OBDII bluetooth dongle and I realize that at WOT the ECU is only seeing 85% from the TPS. O know on some vehicles there is an actual procedure like turn the key forward, hold the gas pedal at WOT, turn the key all the way forward w/o starting while pulling the turn signal stalk down or something crazy like that to force the ECU to re-measure while you keep the gas pedal pinned to the floor. I know on other cars when it doesn't read a full 100% you miss out on a small amount of power and MPG so if it's an easy procedure with these cars I'd like to reset it. I did some searching but mostly came up with info on how to replace it and a few related subjects but noting on this specifically for this car specifically.
View 2 Replies
Replacing the tps themselves? Is it something a newbie at diy car stuff can do? I'm getting codes P2016, P1295 and P161B, and I see no problem with the car except one thing, when the engine is cold the shift from P to D is rough. Is the tps causing this?
View 9 Replies
2004 VW R32, No engine mods. I did have the vacuum line sealed off for the flapper mod for about 3 months but is is now back to normal.
I've got the MIL, ESP, and EPC lights on and scanning codes as follows:
Code-P0222
Definition:
- Throttle pedal position (TPP) sensor/switch "B"
- Circuit Low
Explanation:
- Open or short circuit condition
Probable Cause:
- Poor Electrical Connection
- Faulty TPP sensor
- Faulty throttle valve control module
I don't know much about the situation but I took it to my friends shop first where we replaced the Throttle body, intake, and MAF. Didn't fix the problem so I took it to my local VW dealership and the tech's exact words were.."the codes coming up as a throttle pedal sensor. Is there perhaps a sensor by the pedal that I could check?
View 1 Replies
Am getting an EPC light + limp mode + code for accelerator position sensor (implausible signal). I have swapped out the pedal assembly, so it isn't the sensors themselves, and we've checked the wiring to the pedal assembly... I can feel in-car, and I can see via VAG-COM that one of the two sensors is basically toggling between a sensible % reading of pedal position at one moment, and then zero % the next, and of course every time the sensor reads zero, the ECU notes the error and cuts power... but this only happens when the steering wheel is straight or when turning to the right; I can drive around in a leftward circle all day and night without this occurring.
Why? What is there in the steering (either in the column or at the wheels, or basically any place in between) which, if malfunctioning, could affect the accelerator position sensors in one way or another (i.e. either through the normal operation of a safety system, or through a short or other electrical gremlin)?
View 12 Replies
The Problem: When I start my Ranger it dies right away, I do this about 10 times or so (worse when it is wet or has rained) then I can finally keep it running, by hitting the gas. Once I get it running it will cut out while driving as well. The idle is normal and if fires properly, I just took it in to the shop (non-dealer) and they said it fires normal and has normal fuel pressure, and the their computer returned no error codes. Their sugestion was replace the throttle position sensor. Do you all think this part could be the cause and where is the this sensor and is it hard to replace?
View 12 Replies
Ford catalog does not list the TPS for a 1999 7.3 Super Duty as a separate replaceable part which leads to replacing the whole throttle pedal assembly. I found this to be incorrect. If you have a throttle pedal assembly with separate TPS (separate 3 wire connector) and IVS (Idle Validation Switch 2 wire connector) just the TPS can be replaced.
This is a pic of my 99 with new TPS installed : [URL] .....
Without removing the whole assembly you only need to remove the 2 T25 screws and the connector to replace.
Since this part is listed for more then 20 Ford trucks I figured it would work in my 99 7.3. I bought a brand new TPS from Pete (F250_) that he could not use. He has a 2002 with one 5 wire connector. It works perfectly in my 99. Not sure if it will work in a 2000 or 2001 but if the TPS and IVS each have their own connector it should. Make a visual inspection to be sure.
Part DY-967 or F4SZ-9B989-AA - Potentiometer
I was going to go with a Dorman TPS but like PartsGuyED likes to say "OEM Baby". The OEM TPS through Ed is actually cheaper then the Dorman.
Side-by-side pic of the old and new TPS. Only the center rotating part is different but it fits and works just fine. It also has a better fit so there is less slop and almost immediate response.
NewOldTPS.jpg?t=1269362105
By the way, the original TPS was working fine so I have no idea what the symptoms of a bad TPS are. Since it was available I replaced it to have a spare and to see if this one would work. Both Pete and I thought it would and we were right.
View 14 Replies
Background: Check engine light indicated a problem with the throttle position sensor (unfortunately, don't have the exact code). The TPS on my model ('96 Dodge Intrepid 3.3L) is the non-adjustable type. There are three wires going to the TPS -- a power source, a signal wire, and a ground. The TPS acts as a potentiometer and depending on the throttle position, sends a voltage signal down the signal wire to the computer.
Here's my question/issue: After disconnecting the TPS, I tested the three wires with a multimeter. Power source (5V) and ground were fine. But I'm getting a voltage reading of about 4.35V on the signal wire. It's my understanding that with the TPS disconnected, I shouldn't be getting any voltage on that wire. Does that sound correct? If so, what would be causing me to get a voltage reading there? I'm assuming some type of problems with the wires, maybe an exposed wire on the signal wire somewhere?
View 6 Replies
Recently on two occasions I pressed the accelerator clear to the floor with no response. After shifting into Park then back into Drive it drove normally for about a week. Now it has stalled out and was very stubborn to restart. Once running, the accelerator will sluggishly rev the engine while in Park, but in Drive, will not respond. TPS sensor or something else?
2004 6.0 Diesel, 75K miles, no mods, well maintained.
View 5 Replies
1995 Ford Explorer, 4 ltr. engine, pushrod. Will not start. Replaced fuel pump, fuel filter, every relay, pressure regulator, and the crank position sensor. I realize there's a whole bunch more parts under the hood, but I am ready to give up. Before the fuel pump would not run. Reason for replacing the parts. Now it won't stop running and you can feel the fuel by-passing at the pressure regulator. When checking the pressure at the rail I get zero !! I used a tire pressure tester for this. And, like I said no pressure. This vehicle has around 170,000 miles on it.
View 8 Replies
168k and going strong..kinda. At @35mph it shutters then seems to go into gear. At @ 45mph it revs and the techomter goes above 2k rpms and it feels like I'm using the brake pedal, but I am not. Simple fix(not alot$$) or major? PS, I've changed trans fluid but no luck. If I stay below 45, no problem. Seems 3+4th gear have me stumped?
View 4 Replies
