Passat - Volkswagen :: 2006 - Decelerating At Rapid Pace When Gas Pedal Pressed - Cruise Control Act Intermittently?


Aug 24, 2012

I have a 2006 volkswagen passat 3.6 litre v6- have had this car about a year now, 60,000 miles, no problems until recently. Last week I started noticing that when I am driving, with my foot on the gas, it would intermittently act as if it was decelerating at a rapid pace( will drop gears, is NOT a coast)- even when I floored it!! As soon as it stops responding to the throttle I can floor it, nothing will happen, then let the gas peddle go- then reapply gas and it will act perfectly normal- no flooding, no nothing!! I have been able to keep it floored( while it is decelerating) for about 30 seconds, and it seems to make no difference.

The only other problem that I have recently noticed was that my cruise control was acting only intermittently as well. Oh, also while all this is happening it isn't throwing any check engine, or error lights. I have taken it to the dealer, and also to another specialty mechanic( with master certified technicians) and neither seem to find any problem with the vehicle, the only code that they said was found was one to the mass air flow??, but they weren't sure that was actually the problem, as, of course, they cannot seem to replicate my problem, even though it is now happening quite a lot. I am worried about driving my car now as it is quite a hazard when it decelerates rapidly, and to top it all off, we were supposed to leave for a 2,000 mile road trip in 10 days.

View 7 Replies

Advertisement

Subaru - Outback :: 2007 - Gas Pedal Intermittently Become Unresponsive / CEL And Cruise Control Light Blinking

I have a 2007 subaru outback ll bean addition with 67,000 miles. For the past year and a half my gas pedal has intermittently become unresponsive. The engine is running just fine but the check engine light and cruise control light start blinking and boom-no gas. After turning off the engine, the car won't start until the gas pedal has magically started working again. The dash lights continue to blink for several starts but then stop.

Prior to this problem, I have noticed that sometimes the console lights for the radio and AC blink and sometimes go dark at which point the controls are ineffective. As if this wasn't enough, just yesterday when trying to start the car, the engine was having trouble turning over with a rapid clicking noise. It eventually started but now the seat belt buckle alarm is out of whack and the speedometer displays "ER U1."

View 10 Replies

Passat (B5) :: 1999 - Cruise Control Works Intermittently?

I have a 99 Passat 4 cyl turbo and the cruise control seldom works. Sometimes it works, sometimes not, and sometimes it shuts itself off. What could be the problem?

VWFahrer

85 Jetta Diesel

93 Eurovan

99 Passat

View 3 Replies

Passat (B6) :: EPC Light Coming On Intermittently / No Fault Code And Cruise Control Loss

EPC light coming on intermittently on the morning causing loss of traction control and cruise control, occurred 4 times in 6 months. No fault code logged in, no CEL in dashboard. The dealer checked for logged codes, none. Also had one time the low coolant level display in dash all during one ride to work (30 km) the coolant tank was full and even if I was cycling the ignition switch it was still displaying it. Back from work it was disappeared and never came back on. all EPC light coming on at morning, and ok when coming back from work 9 hours later. Any clue on this?

Car is 2007 Passat Wagon with 2.0T FSI 6 spd manual

View 2 Replies

Honda - Accord :: 1999 - Engine Dies When Pedal Pressed Down / Revs And Then Quits When Pedal Is Pressed Slowly

Ok, did an intake manifold cleaning on my 99 Accord the other day, and now I have problems...

Long story short, some time ago my car started to have a very rough idle. Took me awhile to find the problem. Turned out the air hose, between the filter and throttle body, had developed a big hole on the underside. So I replaced it and while I was at it used some throttle body cleaner, spraying into the intake manifold chamber. Lot of junk blew out the tailpipe. The car ran much better, but the idle could still be a little rough. I ran it that way for awhile, and finally the other day decided there was probably still some junk in there and it was time to really clean it out. So I took ff the throttle body and intake manifold housing. There was a lot of junk in there! The small intake on the passenger side was completely clogged shut. (I understand this isn't surprising on these cars.) I used a bunch of rags and 2 cans of Valvoline throttle body cleaner and a lot of elbow grease and cleaned it out. I was thinking to myself that whatever I didn't get with the rags flushed through OK, but I didn't want to take the whole intake manifold out.

So I put it all back together. (I took a video before I started, so I'm pretty sure it's all back together right.) But now I have problems. The car starts. It idles fine mostly, but can be a bit rough. But the trouble starts when I put the pedal down. If I do it in Park, well, if I push it quick the engine just dies. If I push it slow, the engine revs then quits, revs and quits, over and over. Similar if it's in gear. If I push it hard, the engine stalls. If I push it gentle, it revs up, but chugs along a bit.

I've run some seafoam through it, thinking it was clogged up with all that junk, and sure enough, lots of smoke comes out, but nothing is improving so far. What have I done wrong?

View 19 Replies

Silverado :: 2008 - Cruise Control Not Activating When Pressed The Button To Turn It On

Yesterday I was driving my truck and went to activate the cruise so I pressed the button to turn it on and hit set but nothing happened. The on light was lit but the cruise indicator didn't light up in the speedo. I got to where I was headed, shut the truck off and on my way home tried this again to have the the cruise work normally. Cruise acting up and not work on occasion? I've never had the cruise control act up before so is there something I can check out? Bad connection or something?

View 1 Replies

Passat (B6) :: 2006 VW - Cruise Control Current Speed Display

When I first got this car about 2 months ago, my current speed would be displayed in the MFD when the cruise control was set to on (not activated and in use). For some reason now that no longer happens and it just shows dashes. The only time the speed is displayed now is when I am actually using the cruise control. Is there a way to get that thing back to showing my present speed like it did before?

View 7 Replies

Passat (B6) :: 2006 - Showing Cruise Control Exclamation Mark?

My 2006 passat is showing an exclamation mark beside the cruise control symbol in the instrument panel. And sometimes it will work for 3 months and then sometimes it will cut in and out every day.

So far it has been on for 3 days straight. Anything I can check to see why it is doing this?

Also It worked for 3 months until I un-hooked my battery to install an amplifier and it started messing up the next day again.

View 4 Replies

Volkswagen - Jetta :: 2010 - Err When Turn On The Cruise Control Toggle

I have a 2010 VW Jetta that now displays "Err" when I turn on the cruise control toggle - It is an automatic and all the break lights work - How do I self diagnose and fix? Or is the something the tech wizards at VW will need to do? Not really looking forward to a expensive repair being that cruse control does not effect the car's performance.

View 7 Replies

Volkswagen - Cabrio :: 2002 - Cruise Control System Disconnecting Randomly

my 02 VW Cabrio has the nasty habit of the cruise control disconnecting at random. A tech supposedly diagnosed a faulty Cruise Control Module. Now the diagnostic is the vacuum pump. He did a throttle body alignment, the steering column switches check out, brake light circuit checks out, vacuum hoses all good, electrical connectors all tight and sealed with goop... so what could the problem be? It seems to work when cold and at lower speeds, but after warming up and doing freeway speeds, it's dead in the water and won't reset...

View 7 Replies

Prius (Gen 3) :: Cruise Control Engaging Intermittently

Had an intermittent problem with my Cruise Control engaging. The CC light would come on when the CC on/off button was pressed.

When the CC would engage the "set" light would come on and the speed would hold. On occasion the CC would not engage.

I looked are reread the owners manual.....NOTHING! I was double checking to make sure there was nothing different with the hybrid. (I have owned Toyota for a very long time...since 88').

Since the Hybrid is new to me, "shifting" is a little bit different. There is a "B" on the shifter which is mentioned for "downshifting". There is no mention that once you are done with downshifting that you must shift back to "D" for normal operation. The only mention is not to run in "B" for an extended amount of time.

So, when you are in the "B" position, the CC with disengage.

View 9 Replies

Prius (Gen 2) :: Cruise Control Only Works Intermittently

First it wouldn't turn on, at times now it at times won't work even though the light is on, on the dash. At other times it works as expected. I dun think it's the 12V battery, because when only the center console is on in diagnostics the battery reads 12.2-12.4 and 14.5 + when the engine is on.

View 13 Replies

Avalon 2005-12 :: Cruise Control Working Intermittently For A While

The cruise control on my '05 Avalon Limited was working intermittently for a while. I'd hit the button to turn it on and nothing. Then a few miles down the road, I'd hit it again and it would work just fine. Today I tried to turn it on and nothing. Three different trips today and no luck.

View 1 Replies

Ford Excursion :: Cruise Control Not Working Intermittently?

I had had intermittent issues with the cruise control not working in my excursion. most of the time it was fine though. after a recent 150 mile trip it stopped working half way through. i didnt worry about it too much..got back into town and checked under the hood. i found brake fluid running down the inner fender well! all over everything under the master cylinder. finally tracked it down to the cruise control switch on the master cylinder leaking. I pulled the plug apart and it was full of brake fluid.

Meanwhile the master cylinder was about half full, so i replaced it with the same switch out of a '96 parts explorer which is the same part luckily. also yes i have had the cruise control recall done. So if you have lost CC and you have a leak replace the switch! seems it can leak..and at a pretty good rate..alittle scary! glad i figured it out before my 800+ mile trip later this week/weekend.

View 5 Replies

Ford Excursion :: 2002 - Cruise Control Would Come On Intermittently

2002 Ford Excursion cruise control inoperable. Problem began when cruise would come on intermittently. I would push the on button then set, at which point the green cruise icon light would either come on and the cruise would set or she would flash and not set. Sometimes holding the switch down worked, other times not. Now no matter what I do the cruise will not engage.

I have had the recall done for the cruise control by the dealership.
I have checked the fuse on the recall module, the 2.5 is in good shape and not blown.

I also found this guide to a self test (copied below). I used the test, turning the key on with the off button depressed yields a green speed icon light. Letting go and pressing on yields a green flash as well. But when I move on to pressing resume I get no lights at all, same if I continue through the other switches, no more lights.

Here is the self test guide -

*cruise control self test

Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo.

Release the OFF switch.

Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL. If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch. NOTE: There will be a slight delay when the last button is pressed and the lamp flashes.

A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective. If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).
3 flashes - deactivator switch is open or circuit defective.
4 flashes - vehicle speed signal is out of range or circuit is defective.

Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

View 1 Replies

Prius (Gen 2) :: 2005 Toyota Cruise Control Intermittently Will Not Activate

My Prius cruise control will intermittently not activate when I try to turn it on. One day it will turn on and work fine. The next day I can not get it to turn on. I took the panel off of the back side of the lever and the contacts look ok for the on/off button.

View 8 Replies

Ford - F150 :: 2009 - Cruise Control Works Intermittently

The Cruise Control on my truck works intermittently. Sometimes it cuts out when I am driving and sometimes it fails to work at all (usually in the morning). Sometimes it will re engage if it cuts out and sometimes it will not re engage for hours.

View 1 Replies

Repair :: Engine And Cruise Control Lights Keep Flashing Intermittently?

My engine and cruise control lights keep flashing....This happens intermittently (been going on like this for several months). I took it to my mechanic and he cleared the computer...was fine for awhile...but happening again. Mechanic said that if it happened again, it might be the catalytic converter. I hope not b/c this is a very expensive part to replace!!! Is my mechanic correct or could it be something else?

View 3 Replies

Ford Excursion :: 2003 2WD - Cruise Control Working Intermittently

2003 X limited 2wd 6.0L ... My cruise control was working intermittently. Could it be the buttons on the steering wheel itself? there is a cluster that I see. Does it pop off to expose the connectors/switches? Can these go bad? Can I buy new switches for the steering wheel?

View 2 Replies

Prius (2004-09) :: Cruise Control Intermittently Flashing On Dash As Malfunction

I just returned from a 4K trip through 7 states and my cruise control will go batty and make you pull over and re-boot the car. Basically I am cruising down the interstate with cruise control on. When I come into a town I will either pull the cruise lever forward or step on the brakes to disengage it.

The traffic comes to a stop or slows to a crawl for a short period of time. Once the traffic starts to move again and we are back to highway speeds I can no longer use the cruise control because it is intermittently flashing on the dash as a malfunction. The only time it doesn't do this is when I am slowing down if I turn the power off to the cruise control system.

I stopped in the middle of my trip at two different dealers and there were no codes stored. One dealer charged me a diagnostic the second didn't after I showed him my receipt from the day prior from the other dealer but then he wanted to sell me a brand NEW MFD.

View 8 Replies

Ford Ranger / B-Series :: 2002 - Cruise Control Work Intermittently?

I am normally on the super duty side but I have a 2002 ranger 3.0 auto EX cab if that matters with this issue. My cruse control will only come on rarely but when i does it works fine. Most of the time when I hit the ON button the indicator only blinks like a "relay" of some sort is not latching up. Don't know if this is an all solid state system or if there are electro mechanical relays involved as well. When it does work and I hit the brakes it will drop out completely rather than just disconnect from the controller and need to hit the ON button again, usually with no results.

View 8 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved