Toyota - Camry :: 2001 - Flutter And Idling Rough
Apr 6, 2013
I have a 2001 4 cyl Camry with about 147K. I bought the car from the original owner a few weeks ago. The check engine light came on. The car idles very rough at low idle (e.g., while stopped with transmission in Drive). My mechanic changed out the EGR and another air flow valve that was apparently stuck open too much of the time, and also the engine idle air control valve. The check engine light is now off but I don't think it was related to the rough idle because that started before the check engine light. I have seen other forums that discuss the rough idle related to fuel dampener and also weak/broken motor mounts and haven't checked those out yet.
View 3 Replies
Advertisement
Our '02 Toyota Camry with 92,000 miles has been idling rough for awhile. I tried cleaning the throttle body which actually seemed like it made it worse for awhile. I do need to replace the valve cover gasket and I don't think the spark plugs have ever been replaced. Is that a good place to start?
View 6 Replies
Car is idling rough. Mechanic said it might be an oil restriction not getting to a sensor and advancing the timing.
View 1 Replies
I have a 93 Corolla LE and in October I was driving in heavy rain and the car died. Since then I have replaced the spark plug wires, plug seals, distributor cap, battery, and rotor. The car would get me from A to B, but I would always have to put it in neutral at a stop to keep it from dying. This past week we've had a lot of rain and it's been really cold so my car has been dying when I slow down or stop. I gave it plently of time to heat up thinking it would work, but it died three times on the way to work.
View 15 Replies
ok,up to yesterday, my wife's car started and ran fine. but we had not driven it in about 3weeks, and it was on empty. well, my kids would listen to the radio and, i think, starting it while we were at work. anyway, they ran it out of gas. so put gas in it, 3gallons, turned the key on and off a couple of times to get a good prime. started it up, died, i figured not enough fuel, yet tried again. started, but started spitting and sputtering and idling really ruff, had to hold to the floor to keep it running. removed the maf. it started and did the same. finally, i held down the gas and brake at the same time, took off to the store, got gas, but it died half way there. got it to the pump, put more gas thinking that's the problem. nope, the same. got it home, but when i let off the gas, it idles like it's not getting fuel and dies. so, any clue what it is? remember, 3 weeks ago it ran fine.
View 1 Replies
My wife stopped for gas at a Circle K, about two days later this Sienna started idling rough and missing. I put some Seafoam in it and it cleared up. About one week later, she gets gas again, at another Circle k,about two blocks from the other one. Again, the next day she comes home from work complaining of the van running rough. I took it out and it drove fine. Whenever this happens the Check Engine light comes on, so I ran a code reader on it and it tells me, "Miss detected on cylinder 3".
So I checked all the plug wires, took out the plug (which I had just changed back in Oct.) and checked it, it looked fine. I thought maybe it could be the coil, so I switched the coil to see if I got the same code reading on a different cylinder. I unhooked the battery to clear the code after switching the coils, started it up and still got the rough idle and code. I turned it off (the van) and go in the house, I come back out and start it and it's running fine. I go to the store and all is well, go inside the store for maybe 45 minutes, come back out and start it up, I get the rough idle and missing.
I ran the code reader on it again and cleared the code, then restarted it and it was running fine again. Whatever it is, it has something to do with starting the engine (a 3.1L). One time it will start up and drive fine, the next time it starts the rough idling and missing. I figured if it was the coil and I switched them and got the same code on a different cylinder I'd narrow it down, but so far it has been running normally.
View 8 Replies
My car is a 94 camry, but has a 96 1MZ-FE engine from a avalon. Bought used and has been a great car for ~3 years. Just hear last couple weeks, it would start running and idling rough for a few minutes at a time. The last time I drove it home, it completly stopped on me on the side of the road. It finially started to make it home and now have in the garage. Now it will crank, but won't start. After you crank it, shut iginition switch off, then back to start position, you get a pop out the exaust pipe. From these forums and my haynes manual, I've checked the camshaft sensor, it appears ok (1.1k ohms), crankshaft sensor (2.0 k ohms), 3 of my coil packs, front side (1.4 ohms) manual says .5 to .85 ohms, so i'm not sure about this, the mass air flow meter (2.9k ohms), and it has the 5 volts to it, coolant temp sensor (2.3k ohms), replaced this last year. I haven't checked fuel pressure, since I have to go rent a tester.
View 14 Replies
My Dad Purchased an 06 Camry, 2AZ-Fe engine w/140,000 miles on it from a family member. He was told that the engine had some issues but wasn't specific about the problem. He recently passed and left the car to me. I used to be a mechanic but i have little knowledge on Toyota. The car cranks/starts easy, but idles very rough. I scanned it and the codes I retrieved were p0300,0301,0302,0304. I haven't done a compression test or a leak down yet, but plan to tomorrow. I also will check resistance on the coils and check the condition of the plugs. I looked through some old posts on here, and seen this engine has head bolt issues. pcv issues. and oil consumption issues. Should i pursue trying to fix this or leave this project alone.
View 3 Replies
Having problem with 2010 Toyota Corolla. Engine light comes on as well as VSC and traction control but the engine does not shut off. I loose power and engine runs really rough. I have to pull over and unplug my battery cable and the problem is gone until a week or two later same thing happens. My gas mileage is about 10 km for every 100KM city and Highway mix. The engine idle is also rough and sometimes when I try to do a U turn or get in and out of parking the engine shuts off.
Engine scanned shows P0010 and it could be three or for causes? My problem is that mechanics change one thing which costs an arm and a leg then if that did not fix the problem they say now lets change another part? I can not afford to fix them one by one and get charged for it as they replace one part at a time.
View 7 Replies
I have a 1992 Toyota Camry EL that has been running fine - up until about 3 weeks ago. It has developed a problem of stalling when idling, sometimes, not always. My mechanic has replaced the vacuum hose to the idle air control after finding it was cracked. It kept on stalling after that. Then he replaced the exhaust gas recycling valve assembly, but it still will stall at times. I have noticed that sometimes the engine will rev way up then way down while I'm sitting at a stop light. This morning it stalled while I backed out of a parking spot. Only 95K miles on this car, and I would like to keep it going if possible.
View 2 Replies
2004 Santa Fe 3.5 has started idling rough when in park or when stopped and in drive. When I'm actually driving, it runs smooth and doesn't seem to have any issues or hesitation. I tested my EGR valve with a vacuum pump and it held 7Hg of vacuum and did not leak. I think that indicates it is working still?
I think my issue may be the EGR Solenoid, but I'm not sure how to test it. When I remove the Green hose from the Throttle Body, there is a good vacuum coming from it and my car speeds the idle up and seems to run smoother. I think that means there's some kind of blockage? When I have the Solenoid off, you can blow through it, which I think means it is open.
I think I have to replace the Solenoid, but didn't want to just buy parts.
View 6 Replies
I recently purhased a 2012 Camry, and hear a crackling noise from around the exhaust area as soon as I start the car and during idling. The noise is not too loud, so can be heard from the driver's seat only if the AC is off, windows are down and if the outside environment is relatively quiet. However, when I get out of the car and stand near the exhaust area, it is quite audible. Drove 4-5 miles and stopped and the noise still existed during idling. I'm not sure if it exists while driving as it may not really be audible at the driver's seat. Is this normal or do I need to get it checked.
View 3 Replies
Pretty soon this thing's gonna have ALL new parts and STILL running rough! The Jeep has about 40K on a Jasper motor, 175K on everything else. I was experiencing starting issues (crank for 20-30 seconds), and noticed a P0171 code on my odometer (O2 sensor?) so off to my mechanic. He replaced two O2 sensors, no change. New code read MAP sensor, replaced, no change.
Finally, changed Fuel Pump in tank (Fuel filter was changed 2 months ago), still no change. I tried starting it tonight by turning the key 5-10 sec. to prime gas, started but still rough at idle. Runs strong above idle 1500-2000RPM. Mechanic can't check fuel pressure at rails? for some reason. My next thoughts were spark plugs and vacuum lines...
View 12 Replies
I have a 1997 Toyota Camry with over 200,000 miles. It is a manual: 5 speed. In the past few months it has started to idle at around 2000 RPMS, which is way too high. I took the car into a mechanic where I am currently living (Austin, TX), and they couldn't diagnose the problem, because, according to them, it didn't do it the whole time they had it. I admit, it doesn't do it all the time, but I know something is not right. It is beginning to idle high more frequently. How to diagnose this problem and to solve it!!
View 4 Replies
I got a 1998 Toyota Camry with 2.2L 4 cylinders and have almost 210K miles on it.
Starting about 2 months ago, I was experiencing some minor engine kicking when it was either idling or accelerating, not really such a big deal. About a month ago, I took it to my mechanic shop and he told me that I need to clean up the throttle body. I took his advice, let him did the work and the car still doing the same thing. I did a lot of research on the internet and many people suggested replacing the spark plugs and after I replace the plugs (Bosch, not something cheap), the situation got even worse.
The engine starts kicking more frequently and violently and the “Check Engine” light came on (and flashing). I took my car to a local auto parts store and have their people get the error code for me, it was something about engine misfire and they told me I should have my mechanic to take a look.I took the car back to my mechanic, 2 days later when I called him for update, he told me the cause of the problem was the spark plug cables didn’t plugged in securely. But just before I drove off the mechanic’s parking lot, the engine did it again. I didn’t go back to ask my mechanic because I truly believe he did not want to spend any more time on my car.
Here are the current conditions of my car,
•It never fail to start when the engine is cold or warm
•When I stopped at traffic light, the engine ran smoothly, after about 10 to 20 seconds of idling, it starts kicking. It will do this no matter if my gear in in P, R, N or D.
•When the car is completely stop and then I press the accelerator, the engine will act like it’s going to choke and if I keep holding the accelerator, 2 to 5 seconds later it will rev up and going
•I will be even worse if I have my AC on.
•It runs smoothly if it on the highway
•It always acting up if I try to make a 90 degree right turn and never happens on a left turn
•The “Check Engine” light did come up again but went away 2 days later.
•I made a hard brake yesterday and it took the car about 15 seconds to be able to rev up the engine again.
View 15 Replies
2001 with the 3.1 6cyl. First thing that started this nightmare is I was noticing a bit of a hiccup after driving for a couple miles. We've only had the car a few months and not sure what maintenance was done so we thought maybe it needed a tune up. Before I got the parts the check engine light came on so I went to parts store to get it read, it was P0302.
Did the wires and plugs and it got worse, the code wasn't p0302 now its just p0300. But after the plugs it also started idling really rough and would be slow to shift. Once it tacked up high and wasn't speeding up. That was only once tho. Also now it has no power its like driving a 2cyl ...
Anyway we decided since the first code said 2 we replaced coil 2, no luck..ok, fuel filter and fuel injector 2, no luck. Also has cleaned various things Im not sure of the technical name for..sensors and air filters and other things.
None of this has worked the car still idles very bad and doesn't have the power it should have. Also cleaned things on fuel rail(?). He is in the process of replacing the crank sensor as someone said if it was all the way bad it would throw a different code but it may just be faulty.
View 10 Replies
My wife drives a 2002 Hyundai Elantra GT. Recently the car started idling very rough with rpm jumps back and forth from 1500 to 2500 rpm. The check engine light came on and threw a code for the IAC. I also notice a clicking sound coming from the engine and I can see sparks arching at the coil/plug wire. The arching is happening at the coil with the numbers 1 & 4.
The car is difficult to drive. It shakes and surges and isn't pleasant to drive at all. These issues started happening very recently. The car ran great up until now. We've stopped driving it for the time being until we solve the problem.
We had the car serviced a few years ago and they changed the IAC and mentioned something about a gray wire that we should watch out for.
I'm not really sure what the issue is. I don't know if it is the spark plugs, wires, or coil. Or it could be the IAC or something else. I'm comfortable working on the car myself, but I would rather not try fixing many things if it is just one thing actually wrong.
So far, the only thing I've tried is to spray some carb cleaner into the throttle body towards the IAC in hopes that it would clean it and solve my problems.
Where the IAC is located. I want to try remove and clean it, but I'm unsure of exactly where it it. I know it is somewhere on the throttle body or intake manifold, but I'm not sure exactly what I'm looking for.
View 8 Replies
Our 1999 automatic Rav 4 (157,000 mi) occasionally won't accelerate from a full stop or from a low, in-town speed. You step on the accelerator and the engine just flutters at low rpm, stuttering. If you drop it into neutral and start revving it will eventually "catch" and be fine. Very dangerous when entering roadways. We have a new timing belt, cleaned up throttle plate, new sparks, water pump, oxygen sensor.
View 1 Replies
Twice now my 2001 Echo has overheated when I was sitting and idling it for an extended time with the air conditioner running. The temperature outside was in the nineties. I'm not sure if that makes a difference. After I let it cool down the first time added coolant and drove it, it didn't happen again until today months later. Is this normal?
View 4 Replies
A few months back my 2007 Camry started having this vibration along with a humming/buzzing sound between the speeds of 40-70mph. I seriously thought it was an axle/hub/bearing issue because of the buzzing sound. But at the same time the brakes were wearing down and noticed the shaking of the rotors when braking so kind of figured it may just be that. Explained to the Toyota people and they said most likely new brake service will fix the issue and not an axle/bearing issue. So went ahead and had the brake service done for both front & rear but the vibration & sound is still there. Can't be the tires because just got new ones just last year. Balanced & alignment done and still doesn't solve the problem. Found a TSB, T-SB-0106-08: Steering Wheel Flutter/Body Vibration at highway speeds (approximately 65-75mph).
View 3 Replies
When I'm driving in stop and go traffic during rush hour, my 2007 Camry V6 makes a light flutter when I slowly speed up to between 1000 to 1300 revs. It's not a grind or anything but it's like a light flutter/stutter that you can feel.
It's not a hesitation where the car slows down, but you can definitely feel and hear a light "duh duh duh" then the car continues. It doesn't happen at higher revs at all once the car picks up, say, 10 to 15 kms an hour.
View 7 Replies
