Accent LC (2000-05) :: 2001 GL Started Revving When Driving During Traffic Hour - Transmission Slipping?
Nov 24, 2013
I have a 2001 Accent GL 1.6L Automatic.
Yesterday it started acting up on the freeway. I was driving about 50 during traffic hour when it started revving. I got off the freeway and moved to 35mph on surface streets, the revving continued at lower speeds but much worse (4-5k rpms going 10-15mpg). Doesn't seem to do it in idle or park. If i shut the car off it'll drive fine for a while then start acting up but when I was driving, after awhile, it did return to normal.
What could cause the problem? TPS? Transmission? Sensor of some sort?
View 5 Replies
Advertisement
Just the other day I was driving my car till I've noticed the gears started slipping. At first it was having some issues shifting through the gears (automatic transmission btw). As soon as I got off the highway, I parked in a parking lot just to check underneath the hood. Everything looked fine, went to pull out of the parking lot, no reverse. The gears started to slip up really bad. I noticed that the RPM's kept on reving up and wouldn't go any faster than 20mph. I went to an advance auto parts to get automatic transmission fluid. Still having the same issue and no reverse either. I had to park the car at a location to get it towed back to my house. Some people are saying my transmission is bad, some say it could be a real simple fix. Where to start diagnosing this issue. The car was driving normally until last Monday. My question is where should I start to check and what can I do to see if the transmission is completely shot??
View 33 Replies
My 2004 Accent transmission with 145k miles all of a sudden started slipping while driving. It would be fine until i needed to slow down and then step on the gas again. It wouldn't catch right and it would slip. At first the pull of the slip was very slight and at times now it is very rough. My check engine light does not turn on when it slips slightly, but only when it has a really rough slip will it turn on. I had it checked at the local advance auto parts and i was told it has a 4th gear ratio that is off. The only thing that confuses me is that when i turn the car off and on it resets and works fine, that is until it slips again. If i drive carefully it usually wont slip. Could it be an electrical problem?? I changed my speed sensor when my car had about 132k miles because it went out, i replaced my ignition coils, new spark plugs/wires, tranny oil change, and filter change.
View 2 Replies
I have a 2000 Corolla CE 4-spd auto and I've asked this question from several mechanics and they all say they same: leave it in drive.
My issue is that during my rush hour commute, I'm in a lot of bumper to bumper traffic and the maximum speed is 15mph with a lot of stops. During this time, my transmission is literally switching from 1st to 2nd and then downshifting again hundreds of times. Isn't it better to just keep it in 1st gear? The solenoids are constantly firing and gears are switching causing more wear/tear. It's the same as putting the gear in 1st when going down hill so why do mechanics not recommend this?
View 19 Replies
I have replaced the MAF sensor, TPS sensor, and fuel filter. Like the title says...if I rev the engine ...as soon as I let off the accelerator the engine stumbles and almost dies...then settles back down. I initially pulled codes PO121 so I replaced the TPS. PO103 so I replaced the MAF sensor. PO112..did not address directly as I assumed the MAF was causing. PO1123...again I hoped the parts I replaced would solve the problem. Initially the engine would just drop out while driving just for an instant and then be fine...also I had the 4 codes mentioned above. The only code that has returned is the PO121. I just got done replacing the fuel filter and things seem to be worse.
View 1 Replies
So I bought a 2000 Hyundai Accent for my 16 year old daughter and the guy sold me a car that has a slipping trans. So I went to the Autozone and had the codes pulled and it was a P0734 code. I replaced the trans fluid and replaced the internal bearing and shim with the 42220LK kit from whatever it takes transmission parts store. Trans still slips. What else or should I just unload it?
View 3 Replies
2000 Hyundai Accent GS, 1.5l, 4cyl SOHC...
I have a slight issue. A few weeks ago, I put some "STP" style fuel injector cleaner into my gas tank. Either A) It cleaned everything really well and clogged my injectors, or it turned into gunk and possibly clogged something else up.
Ever since that day, my issue is that the car "stutters" very slightly. When idling, it'll "hiccup." When I'm doing normal driving, 55-60mph at 2k RPM, It'll almost feel like a transmission slip.
I've went and replaced my Fuel pump, filter, and now I've done half a can of seafoam through the brake line power booster (vaccuum) straight into the engine, and the other half into my oil for further cleaning. I also applied Seafoam Deep Creep into my throttle body, just for further maintenance.
Ever since then, everything has been running noticeably better, and I've had a huge increase in gas mileage, but there's still a slight hiccup that occurs during idle and driving.
I change the oil /filter, plugs, wires, air filter on a regular basis.
I also had to change the MAF at one point in time, as it died and the car wouldn't start at all.
Next thing I'm thinking about doing is changing the plugs / wires one more time (it's been about 5 months since my last change) just to see if I bought a faulty plug.
The car was put on a computer and the only error code that came up was one about my check engine light being out.
View 3 Replies
I have a 2000 mercury cougar 2.5 liter. I bought the car without doing much research. now that i have the car did research and found out all the great problems that this car has. My transmission started to make a clunk clunk noise inside and it started to slip. At first it would go on all gears. then very rapidly started to slip in all gears. In matter of hours went from being good to being crap. i had to accelerate the car to 3000rpm or higher to make the car start moving. So i bought a transmission from a junkyard. I install it and did not work. The car did not move on any direction. I pull it out and look at it and found the small shaft that goes from the torque converter to the gear body was broken. I end up getting another transmission from the junkyard. I check it and everything looked good. I install it and got everything back together and that work on reverse but no forward. To get it on reverse I had to accelerate the car to 3000rpm. I being told that if I change the solenoid inside the transmission might fix the problem. It could be the transmission module that is burned out.
View 1 Replies
I'll start out by stating that I failed to get new transmission fluid, which definitely caused the issue. So let's go back to December 26th. Check engine light came on, and I assumed it was for the oil (which has never happened before, suspicious). So I changed the oil, and took it for a test spin. Well, a mile later, I was going up a hill, and the clutch started slipping. Yes, I know, it's an auto, but I know the feeling of a clutch slipping... no power, engine revving up, jolting forward when slip stops. At this point, I drive it home without much incident, a few slips and I part it but don't drive it again. Checked the engine, and transmission fluid was out. Filled it back up, seemed to take care of the problem of slipping, but now there's a new problem...
The new problem is the following. Every once in a while, going uphill or applying full power in first gear, the clutch will slip. Also, this happens 99% of the time, first gear to second gear is a bit of a jolt, not much more than normal, but it's noticeable. And the transmission is kind of loud too, first gear sometimes sounds like there's a marble in there. Is this a rebuild? Will it work itself out?
View 3 Replies
I've been driving a 96 Corolla into the ground for the past 5 or 6 years and recently it's been having overheating issues. It has overheated to the point of steam twice now, and I'm worried at this point I've fried the engine or transmission.
I regularly check the radiator fluids and oil thinking that these would solve the issue, but alas it happened again today ten fold.
While driving home in hot southern california today I first noticed my transmission slipping in traffic. It was slipping when I started moving in stop and go, and settled in once I was going 30 or 40 miles per hour. I had my puppy in the car and was only a few minutes from home so I thought it would be fine, otherwise I would have pulled over immediately.As I got closer the problem got worse to the point where I could no longer shift and move forward. I over revved the engine to get it into a safe spot and it overheated. After waiting 40 minutes I checked on the Transmission fluid (checked unrunning) and it was bone dry. The radiator was full with coolant and oil levels looked good. I put as much transmission fluid as I had in my trunk (not much) back into the car, started it and got the car up the few more blocks I had to go. On the way it was still slipping, at the severity it had to begin with.
My question to you is do you think the transmission is totally shot and I need an overhaul? Or is there some hope that it may have been overheating because it needs a flush/drain and new transmission fluid? The car is at 136k miles and has had a replaced radiator in the past year.
View 5 Replies
I have an 06 sonata 4 cyl automatic.Today the transmission was slipping in first gear like the car was revving in neutral.Then after restarting the car it was completely normal. Code P0731 showed up.
View 1 Replies
Owning a Hyundai. I have a problem and it seems to be pretty common but haven't gotten anywhere with it yet. Last week my 2004 accent 1.6 manual transmission started running rough. It was idling higher than normal and while driving would not go past a certain rpm (about 2500 if I had to guess,no tach). On the way home from work it was running this way and then started badly misfiring and shut off, when attempted to restart it would not. I pulled the codes with a scanner and got p2400, p0562, and p0121. I charged the battery and replaced the throttle position sensor, still won't start. I can hear the fuel pump kicking on when I turn on the ignition. Also found the ecu 1 fuse blown, replaced it and continued to attempt to start with no luck, fuse was blown again. Like I said I haven't owned the car long and I don't know much about it. I am not sure where to go from here and I don't know how all these symptoms are tied together.
View 42 Replies
I have a 2000 accent. Automatic tranny with 167000 miles. My current problem is the car is misfiring upon acceleration and engine revving. I have to accelerate very slowly to minimize this but i once the engine revs up enough I can give it more gas and it will rev normally with plenty of power. I have had to unplug the maf to keep it driveable. Ive never had a car stay running after disconnecting the maf so this is strange to me. My accent barely stays running with the maf connected. I just got the car from my dad and he had it fixed and it ran good for awhile with the maf connected so I don't think it is the maf. But the same problem came about and we had to disconnect the maf again. And he cant remember or is not sure what was exactly fixed on the car. I've read up about the purge control valve and havent had a chance to check it out but some of the symptoms fit.
View 21 Replies
I have a 2002 Accent with 119,000 miles on it. Its an automatic transmission. When I am driving the car feels like it surging forward while I have the brake on...its doesn't happen all the time. But when it does it surges for half a minute, then run fine and then surges again.
View 3 Replies
I have an 02 GS with automatic transmission. The speedometer quit working and now the transmission does not shift out of 1st while driving. CEL is on but I'm waiting for a friend to come over and get the codes. It shifts into drive and reverse fine but I'm wondering if there is a speed sensor in the speedometer that signals the tranny when to shift?
View 4 Replies
My Buick has started acting weird and I've had a hard time figuring out what's going on. As I understand it 94' was the transition year for the OBD1 and OBD2 sensors, therefore auto zone and o'reilly haven't been able to pull codes on my car. It runs off of OBD1 codes but has 16 point OBD2 sensor pins.
Here's the problem: When the car is started it revs up to 2000rpm at idle, when shifted into neutral the rpm jumps up to 3500. In drive and reverse it goes back down to 2000rpm. While driving the car is hard to stop and surges when I take my foot off the break, it also gains speed on flat ground without touching the gas pedal. After driving the car when I put it back in park it revs back up to 3500rpm and is quite noisy.
I've replaced the mass airflow sensor, cleaned out the entire throttle body (there was a little carbon build up but not too bad), replaced all the vacuum hoses(that put a stop to it for about a week), and I'm still having the same problems. I recently replaced the a/c pump because the bearings went bad but I don't think that would cause any problems like this.
I have a very, very slight gasket leak on my valve covers but it's been like that for the last few months and the car was acting fine. The car has done this before but it usually stops after you drive it somewhere. The hotter it's gotten out the more often it started happening and now it's not stopping like it did before.
View 3 Replies
I have a 2001 Hyundai Accent GL the reverse gear went out but all the forward gears work. Ive been told that I need a new transmission. I found a great deal on a transmission from a 2007 Hyundai Accent. Will this transmission work in my car?
View 1 Replies
I am having a few issues with my 2001 accent. I bought this car for around 500 bucks after my friend hit 3 deer with it. At 101,000 miles the transmission went on it and he had it replace with a new one. At about 113k he hit his third deer and parked it. I bought it off him a few years later and its been running great. It died on me one time and it was the crank position sensor. Now I have about a 156k mile on it and it will not go into overdrive.
I have gotten mis fire codes, I know it needs new O2 sensors, and also P0733 Gear 3 Incorrect ratio. The button on the shifter does nothing, If i press it on or off the light does not come on on my dash. I noticed it was not going into OD this last winter if i dropped it into low and shifted to drive it would no longer go into overdrive until i placed it in park and then drive again. Ive been searching everywhere for an answer I was reading one post that it could be the TPS sensor causing issues but i haven't had time to check the voltage.
View 5 Replies
I have rpm stalls then comes back every 2 seconds at idle After one hour driving . Whitout any error code and no check engine . I checked all the sensors and even changed alternator and throttle body completely. No I suspect to crankshaft position sensor .
View 4 Replies
I got a 2002 accent 1.3 si, engine warning light comes on but doesn't seem to affect cars running, no misfires, no stalling, still good acceleration and mpg, occasional engine revving on its own, changed tps sensor and engine revving on its own was worse. Was told by hyundai mechanic to disconnect battery for 30 seconds and if light went out it was either faulty tps sensor or an intermittent non constant fault reading, light did go out for some time but is now back on.
View 1 Replies
I have just changed my clutch and machined my flywheel on my 1.5ltr 16v dohc 2000 lc accent. I used all the correct trans fluid and refilled and bled the clutch fluid. It takes of from lights like a new car but if you put your foot down around 40kph it revs out a bit and does so through all gears untill you reach a bit of speed. What is going on?
View 11 Replies
