Accent LC (2000-05) :: Sudden Loss Of Power - Engine Is Trying To Fire But Will Not Start
Oct 21, 2012
Well zipping along the highway tonight, sitting on 100KM/h, and all of a sudden the engine loses all power. As luck would have it a fuel station was just closing (the only one for half an hour either side) and kept the lights on so I could have a look. The starter is nice and lively, and the engine is trying to fire, but just wouldn't. I asked a mate of mine in town to come out and give me a hand troubleshooting.
As it turns out, when the ignition switch is set to the "ON" position, normally the fuel pump primes the lines. It's only doing it intermittently for some strange reason, and not making it past the fuel filter (despite the filter being new). The temporary buzzing in the engine bay when the car is switched off is gone now too.
Now my question is - does this sound like fuel pump? I'm only used to the older fuel pumps in carburetor vehicles, not these fingle fangle electric things!
View 4 Replies
Advertisement
I have a 2002 accent, 1.5L 16v. So the story is the other day my fiance was driving home and about 200m after she took off, the front wheels chirped all of a sudden and then she noticed it was lacking power. It was still moving along ok and got her home, however it didn't have enough grunt to even get up our steep driveway. I went outside and turned the car off and on again, then all of a sudden the problem was gone and the car drove fine up our driveway. To me this sounded like a sensor or computer issue, although no warning lights are coming up on the dash at all. The next day when driving it, it gradually lost more and more power as the drive went on, but didn't seem as bad as the first day. And again turning the engine off and on again seems to resolve the problem short term. My only thoughts are possibly the maf sensor or the trp sensor. But I'm not really sure.
View 2 Replies
My 2001 Accent GS (1.6L DOHC) wouldn't restart after a short 2 mile trip to a local store. The engine cranks fine but doesn't fire.
It has had a CEL issue for awhile and after it wouldn't start I checked the codes and got:
303
335
722
I replaced the Crank Position Sensor and Fuel Filter but it still just turns over.
I hear the fuel pump run when I turn the key on and I broke the fuel line and it is Pressurized, so I doubt it is a fuel issue.
The 722 code indicates the output speed sensor has an issue. Need to know definitively if that sensor is completely shot could this prevent the ECU from firing the engine?
I have had this car since it was brand new and I'd like to keep it going a little longer.
View 5 Replies
My hyundai accent 2004 standard doesn't start. The engine crank, but there's no fire. I change the camshaft and crankshaft sensor. Also change my timing belt, my alternator, my starter, my control box and my computer. But if I pull the car with my pickup, it runs. While the engine is running, the computer doesn't give me any diagnostic code. I also check my fuse, relay,... Even jump start the starter to check if it was the switch.
View 4 Replies
Ok I got a 1995 toyota corolla 1.8l dx .... So this is my back up car I went out started it up let it set and warm up and took it around the yard to run it a little well it ran fine then all of a sudden it lost all it's power well I finaly got it back to the drive that was only 50ft away took almost 30mins just to get it there. I cut it off let it sit started it back up and still no power well now it won't even start it has new plugs.. Wires.. Cap button.
View 17 Replies
I have passat 2007 2.0T , about 98000km. A few months ago, my vehicle randomly has hiccup with EPC light when I put on the pedal. Each times i put on the pedal my vehicle hiccups and EPC light on and all goes away when i put off my foot from the pedal. It happened randomly, so i went to vw dealership twice. They keep saying they could not find any problem. Coz as i said it happens randomly. I paid diagnostic fee but still the problem remains.
Unfortunately today i had the same issue hiccup like crazy with epc and engine lights. Also on the highway my baby 2 years old was with me when i drove, my vehicle lost power all the sudden, all most i involved an accident with following vehicle. I started the engine, vehicle moves but with the problem. I feel wheels do not spin properly or transmission randomly. What the problem is?
View 1 Replies
Lately having the following issues with my Tig.
When starting up the engine on cold start (or after having the car sit for about 30 minutes) after about 10 - 20 seconds; pretty much right after first acceleration the car all of a sudden looses all power. RPM fall down even when accelerating. Accelerating more only let's the engine stall more.
5-10 seconds later the engine functions normal again.... What problem could that be ?
View 24 Replies
I have a Prius 2005 with an Engineer 4kwh kit installed [v4 bms]. Lately, I have experienced several instances where the Prius suddenly looses much of it's traction power and the engine races, and the red triangle and engine service lights go on at the dashboard. This happens with the kit turned on, and often after a few kit on/off cycles to get more ev mode. The Prius battery is sometimes low, sometimes not, when this happens. Not sure if it also occurs with the kit off.
The Prius seems to retain some traction power up-down by the throttle pedal, but most power goes missing. On the other hand the engine races and does not seem to power the wheels or vary by throttle. When I pull off the road using brakes normally, and turn off the car/engine and restart [kit now off], the car seems to reset and can resume driving normally, but the error code lights [triangle-engine] lights stay on.
View 3 Replies
Ok here's the problem. I have a 2003 grand prix se 3.1 and a 1998 grand prix gtp series II sc. Both have the exact same problem running and both had overheating issues prior to. I can start either one on a given day while cold and drive them as if nothing is wrong. But soon as either one hits operating temp, I start to hear what sounds like a rattling or sputtering like sound from under the hood, accompanied with a sudden loss of power and then the engine shuts off. Now yesterday I attempted further diagnostics with the se model GP. I let it idle rather than driving it this time, and it ran perfectly fine for about 20 mins, started to make the aforementioned noise, I revved the engine to about 2000 rpm and it kept it from cutting off and smoothed, but the second I let up, it was off and wouldn't restart till it was cooled off. Same goes for the gtp. I'm really stumped on this one.
View 3 Replies
So, I have a 2000 Hyundai Accent that has had the CEL light on ever since I have owned it (about 7 months). I was told it was the O2 sensor and did not have it scanned. Occasionally, it would lose power and the CEL would blink. After I would take my foot off of the pedal and baby it for a sec it would usually go solid again and drive okay. About 2 weeks ago it started blinking constantly and it sputters and drives like sh*t. Now, I know that I should take it to Autozone or someplace so that they can tell me which cylinder is misfiring and all, but it is really sketchy to drive. I put NGK spark plugs in it today with no change. I ordered plug wires and a coil pack to see if that straightens out the problem. If it doesn't then I am going to lean towards intake gasket or perhaps a missing or bad o-ring at an injector. So, does this sound like a reasonable plan of attack to get rid of the blinking CEL (misfire) and restore my Accent back to all of its craptastic glory?
View 2 Replies
I have a 00 Accent with 132k miles, I replaced the motor a year ago with a correct 2000 Hyundai 1.5 with 50k miles. I replaced everything that I could at the time, timing belt , starter, water pump, and clutch. It has been running fantastic getting 40 miles per gallon with zero problems , However in the last week I have noticed a rough idle that seems to miss with a vibration that it didn't have before. I have a noticeable loss of power and torque. My miles per gallon has also dropped to about 25 mpg. My check engine light is not on. I will check the plugs and change the air filter today but I would like to know what else could be causing the problem as I am not really sure what to check.
View 9 Replies
2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
View 4 Replies
The night temperture was only about 37 degrees. But every morning my 2000 F-350 7.3 crew cab 188,000 on it would not start. The first try there would be a split second where the motor would fire, but that would be it. I had to plug the engine block heater into my generator for at least an hour before it would start. I don't see how all the glow plugs could be bad at once??
View 14 Replies
I am still failing to appropriately diagnose the problem(s) with my '03 Ford E-350 7.3L Powerstroke. This van has only 69,000 miles on it. A week or two back (just a few days back in work time) it suddenly went from running perfectly smooth, clean and wonderful to this:
- Zero power. Putting the van in gear and flooring the engine causes lots more smoke not nearly any rev of the engine and just a crawl forward.
- Lots of smoke out the back exhaust, whitish. I cannot discern wether it smells like diesel or oil (because I'm ignorant here), but the smell is very strong.
- After warming up and idling ~ 15 min I check under the coolant cap and see no signs of bubbling or disruption (from opening the cap in the coolant tank).
- After warming up there are no warning lights visible on the dash, and I don't have a computer to read codes (if there are any to read).
- I replaced the turbo up-pipes which had a visible leak previously. This did not hurt the symptoms, though no more visual leaks under the dog house.
- I thought maybe I put gasoline instead of diesel in the truck, not so.
- To do the above test I had to use the fuel pump to get gas out the tank to test. I hijacked the fuel pump output and turned the car on a few times to get gas out to a tank. The pump seemed to work just fine.
This was all very sudden which is perplexing, and, in use, the van was previously an ambulette and in my few miles with it (maybe 200-300 only) use was extremely light for such an engine/van, just driving around doing errands. I am not sure if this is relevant (no one has suggested so, yet) but before all this happened I uninstalled the rear HVAC that came with the van when I bought it. The AC lines were sealed under the hood. The coolant line was returned at the doghouse (you can see this at the beginning of the video).
At the moment the van has no power to go anywhere. I have not yet checked the CPS or IPC sensors, and understand this might be the next route in standard troubleshooting?
2003 Ford E 350 7.3L Trouble - YouTube....
View 14 Replies
About a month ago my 2002 accent started intermittently turning on. The car cranks nice and strong when it doesn't start-(until the battery loses too much power from repeated cranking). When it does start, it happens instantaneous, no issues no hard start.
I have talked to multiple people with varying amounts of automotive experience, who have given many things to try.
Things I've replaced or tested, hoping they were an issue:
-Starter and relay
-Fuel pump and filter, as well as relay for pump.
-Battery, post connectors and wires to starter
-Alternator and belt
-Multimeter tested fuel injectors and ran fuel system cleaner for last 3 fill ups
-Replaced spark plugs and wires
-Ran fuel line antifreeze every 2 tanks or so
Things I've been told might contribute to the intermittent starting, but haven't looked into
-Inconsistent fuel pressure
-water in the fuel tank
-Bad ignition switch
-MAF sensor
I live in area, currently in the icy grip of winter. I thought the cold would be a huge contributing factor, but alas, when the car has fired up the temperature has ranged from 1 to -32 degrees and has no issues starting in the deep cold.
View 9 Replies
I just had my '12 GTI's 40,000 mile service done about 2 weeks ago. I put in a K&N air filter the day after the service. The only thing I noticed about the car after service was that I could smell coolant, they either spilled some or its burping some cause it was filled past the max fill line. Outside of that everything was copacetic until yesterday morning.
On my way to the gym with cruise control on ~74 mph on the highway I had sudden power loss, EPC light came on and power returned although felt reduced. When I left the gym it was off and I made it about a mile when under acceleration it hit at about 3k rpm, again sudden power loss and EPC light, power returned reduced. Drove about 5 miles to work and did a little googling with a million results.
When I left work to go home I made it about ten minutes into my drive before it happened. This time the CEL came on. I was able to drive home and back to work again this morning but I keep having power shutters followed by the EPC. I haven't had much time to dig into anything but I checked the connection of the coils and the intake connections with a flashlight at 4:30 this morning. Thinking it might be the MAF only because I recently installed the K&N and have read the oil can kill MAF's and I might stop to get a can of cleaner on my way home to try that route.
IF that doesn't work maybe I can get it on a Vag Com in the next couple days to get it sorted out.
View 6 Replies
I have VW99 Passat 1.8L Turbo, automatic with 170K on it.
My car shop changed engine oil yesterday with 4 QTS of Mobile 5W40. Now, when I check my dipstick today, on level surface, the oil level is way too high on dipstick kink [the cross-hatched mark]. I run the engine, shut it off, and let it set for 3 min, but still the level is too high above the Mark. It wets the dipstick almost till the top of its Head.It was reading High when I first checked it, this morning, before starting my car.
It seems the oil is 'overfilled' or showing over filled; and the engine is about to throw it out from "filler cap" where Dipstick goes in the engine. I saw him using 4 cans 1 QTS oil, which I bought, into my car. They did change the "oil filter" at the same time?
Now, my car looses power while driving. When I accelerated from a stop/light, car slows down or limps. The car suffered a sudden loss of power.It runs awful for about a mile but smoothed out after acceleration.It feels like the car is running out of gas for a few seconds, then all of a sudden it kicks in. The car still drives ok though - No error messages/warnings on dash,CEL, no smoke, no hissing. I actually don't see engine oil thrown out or leaking though.
I don't know if the shop drained the "intercooler" while changing the oil, also I know nothing about its importance to my power loss issue. The net search manual/states "The engine oil, above the level, can be drawn into the crankcase ventilation system, and enter the atmosphere via the exhaust system". But it does says about damaging the engine/car.
Should I be worried about the damage to the engine?
View 8 Replies
I have a 2004 F250 6.0 DuperDuty with about 170,000 miles on it, so far no major break-downs, just a starter and a blinker relay, but now I have a problem.
When I start now, the truck starts fine and it sounds fine, but it has almost no power even if I floor the gas peddle, there is a delay of like 2-3 seconds and then responds slowly, like some tractor. Eventually it starts to move slowly, and after it warms up (after a few minutes), the gas peddle responds more normal.
Also - at about 45mpg, at lower RPMs about 1250, the engine starts to shake (weird), it doesn't do it at idle about 850 RPM, or when I get it up to about 1800RPM+, but at about that 1250 RPM it does do it, luckily I driver locally for a few miles.
What could this be ? What exactly happens when I press on the gas peddle, what systems are involved and in which order?
View 14 Replies
I've got a 2004 F250, 6.0, with 150k miles. I was pulling a motorcycle trailer uphill in the mountains when suddenly I couldn't go over 10 to 15 mph. All the gauges read good but it just couldn't get any power.
Got to the top and checked over everything. Didn't see any issues. Drove it home (200 miles) the next day. It drove okay on highway but it felt like the turbo wasn't coming on. Coolant was low and EGR was gunked up but only slightly wet. From what I read, it sounds like EGR cooler is failing but would that cause the turbo not to come on or feel like that loss of power? Reading another thread, I thought it might be the fuel pickup but I dropped the tank and the sending unit looked very good.
I'm ready to throw on a bulletproof egr cooler, oil cooler and rebuild the turbo if necessary but hate to get to the end and find out none of that worked.
View 5 Replies
My 2011 6.7 suddenly lost power, started making noise and then stalled out.
After finding out that there are zero 24 hour service companies available in the LA area, I was able to get it towed to the local Ford dealer.the next day they told me it had dropped the #5 cylinder and that they would have to tear into it to find out what happened.
While I realize that any thoughts on the situation would be primarily idle speculation, what would cause this to happen at only 125,000 miles.
View 14 Replies
Ok I have an early 2004 F250. Recently changed out the #8 injector and then had to replace the ICP Sensor. Was running great then while driving down the road just died all of a sudden. Would start right back up with no issues. Continue driving and I am getting intermittent power loss. Also noticed that when it would lose power suddenly the glow plug light would come on.
Codes are P0102, P0113, P0272, and P1000.
P0102 Mass or Volume flow circuit low input
P0113 Intake Temp circuit High input
These are just soft codes not setting a light off. MAF is plugged in and I will check wiring here later after work but could this be causing my intermittent issues?
View 13 Replies
