Accent MC (2006-11) :: Shuddering When Vehicle Is Placed In Gear - Code P0301
Oct 23, 2013
When looking at the engine from the front of the vehicle. what numbers are the cylinders from left to right? To curtail off of that question where do I locate the corresponding ignition coils to these c I have been dealing with intermittent misfires on cylinders 1 and 3 codes P0300, P0301, P0303. I replaced the spark plugs to no avail. Whenever the vehicle shudders the headlights dim and the shuddering is worse when the vehicle is placed in gear, the A/C fan is on, or the vehicle is accelerating. Once I reach a certain speed, usually 35-40 mph, I don't notice until I again slow down. I replaced the spark plugs the day after I had the first issue appear which read code P0301. Prior to installing the spark plugs, I experienced a severe loss of acceleration power, but now only experience the shuddering.
2011 Hyundai Accent 63500 miles ....
View 2 Replies
Advertisement
I have a 07 Sonata V6 that misses only when warmed up, runs fine when cold. code p0301 for cylinder one misfire, I have replaced the plug, coil and injector for cylinder one and still the same. idles and runs perfect when cold, dead miss on number one cylinder when warmed up.
View 1 Replies
I have a 2010 model Hyundai Accent showing error codes P0301, P0302. It has a 1.6L engine. I know little about cars, what is going on and how to fix it.
View 7 Replies
I have a 2006 F150 with a cylinder #1 misfire only code p0301. I have done new spark plugs, new coil packs, and new fuel injector on cylinder #1 with no luck. What to do next?
View 5 Replies
After almost an entire year of trouble-free running (with the exception of replacing a ground strap), my 2009 accent decided to start bucking and shuddering again. It only does this when warmed up, runs perfect cold. In the last 16 months, I've replaced the plugs, coils, battery, PCV valve, and ground strap. Car starts with zero hesitation.
Strong battery and starter, consistent output from alternator. After @5 miles, the car stumbles on acceleration, and idles sporadically. While looking at it tonight, I noticed a few exhaust brackets under the car had broken, and the flex section of the intermediate pipe had torn open. Could this presumed exhaust leak be causing the crap running performance?
(My "exhausted" brain thought it could cause the O2 sensor to misinform the ECM, resulting in the P0300 code I pulled...).
View 1 Replies
At low speeds before coming to a stop the clutch shudders somewhat when I push it in. When quickly depressing the clutch when coming to a sudden stop....
View 4 Replies
This week I noticed a sound that sounds low that increases then the vehicle goes faster and decreases when it slows down. It is not wheel bearing noise. Took a doctors type scope and put it on the pulleys listening for the bearing noise in each pulley and found my alternator pulley making more noise than usual, My car needs new accessory belts so I ordered 3 new belts and will be replacing them soon. I am hoping the noise is from worn belts and not the alternator. If it is the alternator its going to cost me 250 bucks for a rebuilt one. I'm not sure if I can tear the alternator apart and replace the part bearing part. Have to look into this. Is this normal for a car with 161 thousand klm for accessory belt bearings on items to start to go bad? I sure hope the water pump and power steering and ac compressor and ac tensioner last. These all have bearings in them as well.
View 10 Replies
I've got a 07 accent with 90k miles on it. It has recently started slipping some (revs high, while in gear, without accelerating, especially in 5th gear). It also can be physically hard to move the shifter into gear sometimes (with my hand).
So, does this mean I need a new clutch? Or are there other possibilities? Should I replace/fix anything with the clutch? Sounds like the flywheel should be resurfaced? Will it shift more smoothly after the fix?
Is this something a newb could do himself? I can change the oil, rotate tires. Outside of that I haven't done much. My toolset for now is fairly limited: two jackstands, a trolley jack, torque-wrench and ratchet sets.
View 12 Replies
2003 Saturn Vue V. 61,000 miles. Drives ,steers and turns normally except when you do a very tight 360 circle. Tremendous grinding sound and shuddering coming from the rear of the vehicle. Return to driving a straight line and everything returns to normal. What is the issue and what would it cost to repair?
View 1 Replies
I have a 2010 VW GTI, approx 48,XXX miles and need a hesitation diagnosis. The car is throwing a P0301 code, I have replaced the plug, coil, and check the coil harness. I think it may be the injector, so I replaced the fuel filter but don't want to do the injector on a whim. I don't want to take it to the dealer if I don't have too!! I live in Silver Spring MD.
View 1 Replies
I have a 2009 Corolla with a 1.8 L. I have the misfire code P0301. I have changed the plugs, ignition coil, and fuel injector on cylinder one. It still has the misfire.
View 5 Replies
The vehicle is a 2002 Ford Windstar van with a 3.8L V-6 engine. It has a constant miss on the #1 cylinder. That's the one on the backside of the V-6 on the passenger end of the engine. I have changed the plug(s) and still had the miss and P0301 code. The plug's wire has about 7500 Ohms, so it's not the problem. I hear no snapping of a high voltage short to ground. A friend suggested that the injector might be the issue, but I am of the opinion that the scan code shows only a high tension or secondary ignition system issue, and not fuel injection issues. I'm thinking the problem is more likely to be the coil pack.
View 19 Replies
We bought a used 2001 Grand Am (V6 automatic) a few months ago. Mileage was just under 100,000. It was running decently at first, but that improved once we did more maintenance. It's gone from about 150 miles on the highway on a full tank to about 250. A lot of the problems didn't reveal themselves until we took it onto the highways. These are the parts we changed in the last 2 months:
-new battery (old one was 0.1 above fail)-all 6 spark plugs-catalytic converter-front oxygen sensor-oil filter-timing belt-pcv valve and breather hose (old one melted)-all 4 shocks/struts
Latest problem is OBD code P0301 cylinder #1 misfire. The entire car started to shake when we were in low speed in a drive thru. It only seems to shake in drive gear and it does it the whole time. It doesn't shake in reverse or any other gear. Found out #1 spark plug was cracked and a chunk of the ceramic portion was missing. It got replaced but that didn't fix the problem. Haven't noticed any white exhaust yet. The ignition fails 1/7 of the time since P0301surfaced.
The last problem we had was P0420. We went to 3 different shops and nobody was able to fix the problem properly. It wasn't until the pcv valve and breather hose were replaced that the code disappeared. The valve was actually cracked and parts of the breather hose were melted. I can't understand why nobody noticed that.
I know there could be a lot going on, but I was hoping the possible problem could be narrowed down.
View 3 Replies
So I changed my spark plugs, due to an error code saying p0301 which means cylinder one misfiring. I reset the engine light disconnecting the negative battery terminal. Once it reset it ran rough for a few miles. I put about 50 miles on it and it seems better.
View 2 Replies
I have a 2009 Prius that I purchased 6 months ago and have been really happy with it until the last couple of months. As the weather is getting colder appears I have a misfiring problem on start-up
I have had this problem now for a little while and have been trying to get it understood before paying $$ at the dealer for "maybe" solutions.
It started as the weather got colder. Intermittently the check engine light would come on. Then after a few days would go off.
I have considered water in the line: fuel injection cleaner/antifreeze
I have considered bad gas in the tank: problem persists several fuel tanks later
I have recently purchased a trouble code reader/diagnostic that plugs into my laptop. Trouble code is p0301. Cylinder 1 misfire.
I have taken it in to the shop.They tried:
>>moving the ignitor coil from cylinder 1 to cylinder 4,
>>and also tried moving the spark plug from cylinder 1 to cylinder 2.
>>performed compression test. Ok
The dealer suggests replacing the injector line for $1400+.( They did this with warm engine. They have not diagnosed cold engine yet. That is new, read more,...) I still have 5K kilometers left on the power-train warranty. If it is power-train I would like it resolved before warranty expires.
Now. Some new info as of yesterday:
Up till now I was not using the diagnostic monitor real time. but that started yesterday,... Last night when I got home from work while the engine was still warm I connected the diagnostic monitor and went for a drive. Every few minutes I would pull over and refresh the cylinder misfiring data. I had hardly any misfires across all the cylinders at all. Maybe 1 or 2, here or there over the span of a 10 minute warm engine ride. Up and down hilly terrain. Nothing that came close to triggering the p0301 trouble code. I parked the car outside and let it rest overnight.
View 19 Replies
'07 Avalon with 169k miles. I replaced all 3 back coils and 6 plugs back in December when I had various misfires, but the most common code was P0301 which is cylinder 1.
Car ran great until last week when I made a hard left and accelerated. CEL started flashing, read code and it's P0301. Every time I accelerate half throttle or more I can set the code off, but then shutting down car and restarting it drives fine, until I go half throttle. Car runs better when cold, and worse when I turn left and accelerate.
As long as I don't mash the gas I can drive for a half hour or so without the strumbling/hesitation. Surely the new coil hasn't failed so soon, I hate to pull the wipers, plenum,etc. and buy another coil just on a chance that might solve the issue. Car is only throwing a P0301 this time, no other codes like before. I've read a clogged cat or sticky exhaust valve could cause a cyl misfire.
View 10 Replies
My 97 F150 through a CEL Tuesday night P0301 so I picked up a new plug because it's cheap and simple, but that didn't do anything. Spark plug wires are about 3 months old, I also swapped injectors between 1 and 2, and misfire stayed with cylinder 1. It also gained a tap when the misfire started but only above idle, but it doesn't sound like a rod knock.
I also noticed if you unplug injector 1at idle it taps/knocks 3 or 4 times, however if you unplug any of the others it doesn't do that. I checked and I definitely have good spark from the plug. I plan on picking up a new compression tester tomorrow since mine never was returned. If you take the oil fill cap off it doesn't have any blow by at idle, however if you rev it you get a quick cloud out of it.
I thought about picking up a kit to check the injector pulse.
View 8 Replies
This happened xmas shopping with the wife. Started misfiring on the highway,took the 1st exit to find a garage as I am 20kms from home. The vibrations were worse at stop, but made it to a garage. They gave me the p0301 misfire cylinder 1, said they don't touch 5.4 plugs, told me to go to ford 2kms down the road. NICE. 4 in the pm, FORD dealer worse case scenario. Nope gave me a loaner told me come back at 930am. Truck was just waiting for an injector when I arrived. Plug & coil were good injector was shot,changed the fuel filter & oil change.
View 6 Replies
I drive hyundai accent 1.5l sohc.. Recently i was on my bots on turbo project.. The process when smoothly until i suddenly realized that my car was only move on 3rd gear.. then i took off my turbo out afraid of over boosting and straight go for diagnostic.. And error p0755 comes out.. So how to troubleshoot this problem..
View 9 Replies
2009 corolla 1.8l 155,000 miles. Replaced iridium spark plugs at 100,000
I got a CEL few weeks ago, P0301 Toyota - Cylinder 1 Misfire Detected
Car has been running bad for about 2 weeks now, excise noise on the highway, especially up hills.
Yesterday, I took a look, replaced the spark plug in cylinder 1, same results. Checked the coils using one of those flashing tools, all 4 flashed quickly, with no breaks in flashing. put it all back together, cleared the code, went home.
Took it out for a drive today, and it started running way worse. Checked the CEL, and now I have both P0301 and P0303 Misfire on cylinder 1 and 3. Barely made it home, ran VERY VERY bad.
Got home, and made a video of it. It just kept dying. Check it out here. [URL] .....
Also, when it does run, it almost sounds like I can hear excess air, its hard to hear in video, but doesn't sound right. Maybe air leak? How do I check?
View 2 Replies
My wife's 03 Passat w/ 1.8t is bucking and lurching throwing a P0301 (Cyl 1 misfire) code. We have about 58k on the engine and had the dealer do the 40k service 2 years ago.
So far I replaced cyl 1 spark plug, swapped and then replace coil pack with new. My choices for parts were limited on a Friday night and these are el cheapo Autozone parts. Still missing and throwing DTC, I don't really have access to Vag-Com anymore (just OBD reader at parts store) and I don't have a Bentley's either (I know there's some eye rolling going on now).
How to troubleshoot the cause so I can make a decision to take to mechanic or do a few more parts swaps between now and Monday. I've got tools and a multi-meter. I used to have Vag-Com but it isn't supported on my new laptop (Vista), I tried the USB extension cord on my desktop but it is hit and miss.
View 3 Replies
