I have a check engine light come on in my 07 Avalon and had the car scanned. It was throwing error code P0031. I'm gonna go ahead and replace this O2 sensor, however, I'm having a hard time finding the correct part# for this sensor.
View 1 RepliesI received error code P0031 on my 06 Avalon the other day. It states that the HO2S (Heated Oxygen Sensor) is bad. Bank 1 Sensor 1. I located the sensor but have a few questions...
Just to give an over view for those that don't know where these are, there are 4 sensors the one in the front on the manifold (upper - B2, S1), (lower - B2, S2) and the rear manifold (upper - B1, S1), (lower - B1, S2).
All of the sensors look the same with 4 wires. what the part number is for the sensor? Also since this is the hardest one to get to, I would like to know where the wire routes to. I found the wire up to the connector on every other sensor except the one I need (B1S1). It looks like it runs towards the top of the engine but from the top I don't see it.
I'm on the lookout for a set of OEM rims so that I can get snow tires for the winter and just realized that I'll also need a set of Tire Pressure Monitors. What is the part number?
View 11 RepliesAny resource that I can use to find the part number of the O2 sensor on my wife's 03 v6 Camry.
I have a check engine light, scanned by code scanner to reveal P2195. This OBD code is supposedly sensor 1, bank 1 "stuck lean" which is the upper O2 sensor on the left side of the engine (closest to radiator with transverse mounting).
So it should be easy to change if this is the issue but I'm having a hell of a time finding the right part number. Too many choices.
So of course it has to happen 3 weeks after my warranty expires. My CEL comes on and I have it read and the result is P0440. I find out that my wife has a habit of topping off the gas tank and so I am thinking that she has probably ruined the charcoal canister. It is something easy to replace?
I have an 06 limited edition... Yes, she will not be topping off any gas tank anymore.
Looking to confirm the part number. My ICP is mounted on the RH valve cover and has a yellowish upper where the three pronged connector inserts.
View 10 Replies2006 Toyota Avalon 72000 miles
Plugs and coil have been switched between Banks 1,3,5 with 2,4,6 code P0355 shows the same cylinder 5 after the switch. What's the difference between a PCM and ECU and which one do I have.
What is the part number to the TPMS sensors for a 2011 Corolla S. Or any stock toyota ones that will work?
View 2 RepliesI have a CEL on my 2007 Avalon so I decided to take it to Autozone to get a scan. Error code P0015 was returned. This code has to do with B Camshaft Position, Timing Over Retarded (Bank 1). I've done a little research and I've read that this could possibly from a dirty screen on the Oil Control Valve, the OCV itself, or the Cam Position Sensor. Before replacing parts, what I would like to do first is to check/clean the screen on the OCV. Secondly, I would like to swap the Cam Position Sensor to a different bank and see if the other bank throws an error. If the other bank throws an error, then I know the sensor is bad and needs to be replaced. With this said, I am having trouble locating the OCV and CPS. Where the valve and sensor is located. A diagram would be useful.
View 14 RepliesLooking for the Ford (or even Dorman) part number for the Water-in-Fuel sensor that bolts to the outside of the fuel bowl?
Guzzle has it pictured here:
The water sensor tip on mine is badly corroded and eaten away.
What's a part number and who sells them that I can get it delivered next day?
The 2005 Avalon has 48K miles and it's been running well without any issues, until today.
Driving in city traffic, max speed is about 30 ml/h, The "Check Engine" light and the "VSC (Vehicle Slip Control) Off" lights came on. I did stop the engine, restarted after couple of minutes and the same lights stayed on. The car ran just fine, no noticeable difference in performance.
With the OBDCOM reader, the Avalon has this code:
P0351 232
P0351 Ignition coil A primary/secondary circuit malfunction
That seems to indicate a malfunction for cylinder A, or #1, ignition coil that has nothing to do with the "VSC" AFAIK. Is this a misread by OBDCOM reader, or the Avalon is confused?
The code had been reset via the OBDCOM reader, the car runs fine, neither of the lights come on now. Should I do something about coil A, or just wait until the code comes back?
Have the P1705 engine code (Direct Clutch Speed Circuit Fault) on 1996 Avalon.
I have removed it and trying to examine connectors and unit for problems.
Seems simpler to replace but cannot see spending the money on a crap shoot. Here is what I know:
Took voltage reading from each of the 2 connectors on the harness each with the key on but car not started. 1 probe to 1 connector and other probe to battery ground. Each connector displayed 0.76V.
Checked resistance across connectors on removed Sensor and it was 600+.
So...are these results determine whether the sensor is bad or the connector harness has an issue? Am I measuring incorrectly? Finally, is there only one of these sensors? I see on later models there are 2. Toyota P/N: 89413-08020
So, my '06 XL just popped up a P0051 code, which is the bank 2, sensor 1 (the upstream A/F sensor that you can easily view upon opening the hood in the front exhaust manifold. Easy enough of a replacement on that one, but what about bank 1, sensor 1 (the upstream A/F ratio sensor on the firewall side of the engine)? I changed my oil today and I can access three of the four oxy/A/F sensors, but the upstream rear looks like a bitch! Out of curiosity, I called a local Toyota dealer and they said it would be 300.00 total to replace the hidden sensor on the firewall side. Does this amount seem realistic? I know that there is a TSB for this sensor that states to replace the exhaust manifold/cat assembly. I def. can't afford no 1700.00 crap right now!!
View 3 RepliesI have an 08 avalon w/ 281k miles. NEED to replace the transmission speed sensor (P0500 code thrown). Where is it located on the trans and what is the part #? I'm thinking about servicing the trans while I'm there but looks like a lot of "comments" regarding this transmission and the problems with servicing it!?
View 9 RepliesSo, I have my check engine light and the code is p0327 (knock sensor). Clear cose but it returns. Going on for 3 days now. I was suspicious that something else is going on. I also remembered I've been using a little more antifreeze in the reservoir. So, today I needed to watch the coolant. I ran the car for an hr and I found a lot. Red coolant on my belt, the back passenger side of my engine and it was caked on with coolant. I think the water pump is going up.
I was concerned that coolant was also leaking from the intake manifold but it's only the right side, so I'm pretty sure the coolant is being slung around from the belt. I rinsed the engine down and the knock sensor code went away. Temporarily, until more coolant got back there. Do you think I will need to replace the knock sensor along with the water pump or should the sensor work ok after some intense cleaning after the water pump replacement?
So I dropped my prius off to get looked at for error code p0301 number 1 cylinder missfire. They ruled out Spark plugs, coils and fuel injector. What else is ther? Also could it be the battery or even gas?
View 12 Replies2006 PT Cruiser Touring Ed. The engine light came on 2 days ago, had it looked at today and the error code p0304 "cylinder number four misfire" was diagnosed. What causes that and what would need to be done to fix that problem?
View 9 RepliesAlright, so I've been battling this for a few hours. I know I need to replace a sensor, and that's about it. The issue, is I don't know if I need to replace an oxygen sensor or an air fuel ratio sensor. I have searched, but I keep finding conflicting information. So which do I need?
View 3 RepliesWe just purchased seemingly well cared for 2009 Avalon XLS. Navigation system is showing a DVD error (unable to read). First we thought it was missing the DVD then we discovered the DVD port in the truck and through some trial and error got the DVD (#U52) out. We are proceeding with the logic that the DVD is bad.
View 6 RepliesIt's time to go thru emissions testing, but I'm getting a P0031. New A/F Sensor (Denso 234-9041) did not fix it. California Emissions compliant.
2003 Camry, 2.4 16-valve
Car runs good, MPGs same as always, 26/27 and 30+
Old sensor has no resistance or continuity thru any of the pins.
New sensor has 2.5/2.8 ohms res between blk/blk pins. (? +B and HT ?)
200K miles, has burned oil since I got it w/ 140K. Have had MIL light on for two years, but did not care until now. Previously had diff DTC's, not P0031.
Swapped EFI relay with Headlight relay, no change.
Checked all fuses, all OK.
Cleaned ground on engine block and fender, no change.
Checking voltage at engine connector, sensor disconnected, car running, I'm seeing
Orange 3.31 = Blue Sensor wire (AF+ ?)
White 3.017 = White Sensor wire (AF- ?)
Blk/Red 3.827 = Blk Sensor wire (HT ?)
Blk/Wht 13/14 = Blk Sensor wire (+B ?)
I cannot find FREE online wiring diagrams anywhere. I have searched TN exhaustively, have not found anyone who actually fixed this problem, or provided a link to a wiring diagram.
So, which wire is the ground ? Should it show 0 voltage ? Is it controlled by ECM ? How do I test the ground continuity ?
Where is ECM located ? I want to unplug and re-plug.
I own a 06 limited and my Check engine along with VSC lights came on. Autozone read the code and it is a P2195 error. According to AZ the O2 sensor cost $500, according to websites the fix is O2 sensor and manifold ~$1800. I don't have that much money. The dealer told me that it was ok to drive with warning lights on. I checked the MAF sensor and it is clean. The O2 sensor or A/F sensor Stuck Lean - bank 1 sensor 1. If I want to do the work myself, any diagrams, picts, instructions etc......
View 8 Replies