Camry :: 2004 LE Showing Code P0705 Transmission Range Sensor
Dec 30, 2013
I bought 2004 Toyota Camry LE 2.4 couple of months ago, Been running good with no issues , no check engine light . Today I had it detailed from the inside and got it clean at a shop , then took it and changed the transmission Oil at Jiffylube . after leaving the shop the engine light came on . I then took it to a local Auto car parts and had used a car diagnostics scanner to see what was the problem and this showed up P0705 Transmission Range Sensor . I deleted it , then while driving around town , it came back on . I live in Minnesota and it is very cold here, not sure if the cold weather have to do anything with it, but i doubt it. The car looks and seems to be running ok .
View 5 Replies
Advertisement
This is what I get from the DTC .....
DTC P0705
Description : transmission range sensor circuit malfunction
State : History
I have done some google search on the above diagnostic trouble code P0705 and as i understood , it indicates that the Engine Control Module (ECM) has received an input error from the Transmission Range Sensor (TRS).
Since the check engine light illuminated two times (two separate occasion) then it turns off now; the ECM is actually receiving input signal from the TRS.
So that leads me to think that the TRS is actually working but the problem might be one of the following two:
1- Open or short in the TRS circuit?
2- Dirty transmission fluid.
What do you think the steps i should do first of all ? how would i check the transmission fluid since my vehicle has no transmission fluid dipstick. My driving condition would fall into "severe" category and it reached 60,000 miles now ...
View 10 Replies
I have replaced the transmission Range sensor (with OEM) and it is adjusted correctly, however This did not clear the. Code P0705... I am stuck ....
View 1 Replies
The MIL light came on and I noticed the shifting P-D or P-R was hard. Checked the Transmission Fluid and noticed it was low. Topped it up, but still MIL is on and shifting hard still. I bought a OBD2 Scanner and it returns P0707 "Transmission Range Sensor Circuit Low Input". Should I try clearing the DTC? It's a drag because it's my wife's car and she's driving mine.
View 1 Replies
Got a code of p0708 on 2003 ranger flex-fuel 3.0.. Which is I believe is Transmission Range (TR) sensor. Not sure where to find that on truck...
View 1 Replies
1999 f250 SD 5.4 reg cab 320000 km. (200000 m for all those south o the border)
Short story is after plowing truck doesn't like shifting out of second. usually works again next morning. Took it in to have tranny flushed/serviced. No change. obd says p0705, transmission range sensor circuit malfunction. today just as I got home I gingerly (seriously not boring the snot out of the truck) started using the plow to shave the bank out of a corner of my driveway. started taking its time to shift into D. reverse is fine.
Finished what I was doing and went to turn around, backed up 3 point style and it wouldn't move forward in any position tried D, 2 and 1 and nothing. put it into 4wd low range and it did move a bit, tried it again in 4wd high and nothing, tried it with 4wd off and nothing. eventually it felt like clutches engaging like the abs would, very grabby but not moving much.
As I said I already flushed the tranny and had a service done on it. From what I read my next step is to change the transmission range sensor (same as a neutral safety switch yes??) What could my problem be?
View 5 Replies
I was pulling the I-40 ascent to Asheville today while empty, got to the top and started down the other side got to semi flat road and the tach suddenly went up about 600 rpm's. Transmission temp about 180*F. I let off, then resumed and everything was fine. About a mile later it happened again. This time the tranny lost 3rd and OD, still had 1st, 2nd, and Reverse. So, we limped into a service station. Temps hovered in the 170-180 range. At this point there are no codes, no lights, O/D is not flashing.
I shut the truck down to check fluid level and current condition. Everything was fine last night. Fluid level is still good and fluid is still red and clean. I changed fluid about 2k ago and the fluid coming out looked almost as good as the fluid going in.
Got back in the truck started it up, checked for codes and got a P0705, put the truck in gear to get to a diesel shop down the road and everything was fine, shifted completely normally through all the gears. This lasted until about 1 mile from home and then the same thing happened all over again. Fluid still looks clean, not burned, still no CEL, no flashing O/D, but only have 1st, 2nd, and Reverse.
View 14 Replies
I recently had a thread going regarding my 1999 F350 2wd auto transmission slipping in/out gear. Tried to follow up on old thread but got confused so I'm trying to start a new one. Basic problem is that truck was slipping in/out of gear. Cleaned the solenoid pack electrical plug (as instructed on previous thread) and the truck didn't act up for 2 weeks. Today it started slipping in/out again and this time it registered a code of P0705.
View 7 Replies
I am looking to verify that replacing the Transmission Range Sensor on my 2002 SE is the correct action for me to take. My symptoms include:
1) Fuse 17 keeps blowing intermittently but frequently. It has never blown in a middle of a trip. Have not determined if it is blown at end of trip or right at start of next trip.
2) All gears are highlighted (have boxes lit up on all gears) when I am in park or neutral. The correct gear is highlighted when in any of the drive gears including reverse. This symptom is constant and has been for a few months now.
View 2 Replies
Code was showing for the knock and climbed under the truck and checked to see if it was plugged in grabbed the wire and to my surprise the wire kept coming and so did a piece of the knock sensor, is this going to affect my truck badly?? worst case?? 97 f250 4.6 standard
View 4 Replies
I had CEL the other week scanned and found P2043 Reductant Temp/Sensor range. Light came on first thing after a cold start.
View 13 Replies
My check engine light popped on for me a couple days ago. P2043-reductant temperature sensor range/performance. Truck still runs like a raped ape, no change in driveability. Just over 21k miles. No "speed limited to 55" messages or anything else. Basically no change in the truck other than the light.
View 12 Replies
I have a 2007 f-250 6.0 liter turbo diesel. I was pulling a trailer with a golf kart on it and was not in tow haul. I was going up a hill and it shot up into 5th gear. I pulled into my house and shut it off and refired it and it acted fine. I went on a little test drive to see if it was going to do it again before I went on my trip. As soon as it shifted into third gear the tow haul light started to flash on my dash and went to 5th gear and would not down shift even if I did it on the column.
I scanned the truck with my snap on modus and it gave me these codes. P0706-transmission range sensor A circuit range/performance, P0707-transmission range sensor A circuit low input, and P1702-transmission range sensor circuit intermittent. I put a transmission harness in it and started it up and it ran fine and the codes were gone. I went for a test drive around the neighborhood and as soon as it hit 3rd gear it did the same thing as before. Today I put the old one back in and checked the codes so I could write them down and there weren't any so I went for a drive and it shifted through all the gears great and downshifted fine as well.
I pulled into my drive way to check for codes once again and there weren't any. I was gonna go for a ride in tow haul to see if it would do it and as soon I put the truck in reverse it started to idle high and the tow haul light started to flash again. I put it in drive to pull back into my drive way and it immediately shifted into 5th gear and threw the same codes...
View 5 Replies
I just bought an 04 camry 4 cylinder. It was running perfect when I got it but the moment we got home it threw a CEL. The code was for an upstream o2 sensor, however I did a resistance test and the heater circuit is fine. I did a voltage test on the blue and white wires and I got 3.3v and 2.9v. I don't remember which wire gave me which voltage at the moment. I would like to know if this data is a good thing or if it's broken. I do not have any data to go off of, and I couldn't find the factory service manual online. Its also worth mentioning that it idles very rough and the catalytic converter is giving a rotten egg smell but not all the time. When neither of these things happen the CEL goes away. I do not want to start throwing parts at it.
View 1 Replies
Elantra GT 2003 ... I had engine check light on and OBD 2 code reader showed DTC P1529 and P0705. I erased the codes to see if they comes back and one month later I have same codes back. P0705 indicates Transmission Range Sensor Circuit Malfunction, so probably I should check range sensor. How the range sensor looks alike and where to find it. Where can I find it?
View 1 Replies
When my 2012 Camry's automatic transmission shifts gears in the 20-30 mph range, there is a hesitation during the shifting. I had an independent automatic transmission technician test drive my Camry, and he said my transmission had "light throttle 2-3 slide." He also noted a high frequency clicking sound in the vicinity of the transmission while the engine was running, which he said may be a malfunctioning solenoid.
View 5 Replies
I have played around with settings and wanted to see if I can have range/distance to empty showing in this screen. Doesn't seem possible. I tried looking through the online manual.
View 2 Replies
My 2003 Camry has po301 fault code also have same code showing as pending. Can't find nothing on google regarding duplicate codes . The car starts fine, runs fine, idles fine. Excellent at high speeds I don't think the car is misfiring . Could it be a bad sensor giving me a false reading .
View 6 Replies
My 2005 prius is showing POA93 code. Is this always an inverter coolant pump or can this be caused by other issues?
View 2 Replies
What is the range is on these temps. Reason I ask is because long story short My truck did not come with a factory tow package and I have added the hitch and seven pin wiring, I am lacking the HD trans cooler. Recently purchased a travel trailer and am a little worried about getting the tranny too hot. I have an Edge tuner and set the gauge to read tranny fluid temp. Without the trailer I have been seeing temps that range in the 130's to 150's, with the trailer I have been seeing temps in the high 160's, with a spike to 176 when going up a hill. I plan to add the tranny cooler but cash is little tight at the moment. Just wondering how hot is too hot.
View 14 Replies
I have recurring P0705 trouble codes. Lexus dealer checked the N/S switch itself and said it's good. I checked all the wiring, found an open, shouted Eureka! Ran a new wire, now all wires test good, but still getting the code. SO - I think I may need to adjust the position of the switch, since the trouble code is for a range malfunction. BUT - I can't find a procedure anywhere.
View 3 Replies
