Camry :: 2006 Toyota Surges At Any Speed / Loss Of Power - Code P0420
Dec 15, 2014
Symptoms:
-Car "Surges" at any speed. Loss of power is significant.
-Check engine light is on , DTC code = P0420
Tried:
-Fuel injector cleaner
-Spark plugs replaced around 40k miles ago
-Checked for leaking valve cover gasket (oil in plug wells) None
Can a clogged fuel filter cause this? At idle the car is fine, the symptoms seem to only occur when car is under load (In drive). My son drove this car an it always seemed empty meaning he never put much gas in it.
View 14 Replies
Advertisement
I've got an '05 Tacoma 4WD with 145,000 miles. Very recently, when taking right curves at moderate speed ( e.g. freeway cloverleaf onramps), I'll lose power at the apex of the curve. It comes back immediately when the I straighten out. No warning lights on panel. It feels like no gas since there's no difference when I press the accelerator pedal.
View 17 Replies
My Toyota Tacoma is reporting (via an affordable OBD-II scanner) the same P0420 code: First as a regular code, then as a pending code. What could that mean?
View 6 Replies
I have a 1995 Camry with the 4cyl 5sfe engine and a manual transmission with about 120K miles. It's been very reliable overall, but lately it's been exhibiting some strange intermittent behavior. When driving at a steady speed between 2-3K rpms, it'll sometimes experience a momentary power loss. There's no stalling, but it's as if I've hit a stiff headwind or the brakes have been applied and then release. It doesn't seem to happen when accelerating, but as mentioned above, it's most noticeable when maintaining a steady speed. Sometimes it'll be very quick like it's bucking and other times it'll last a full second or two. It'll do it in all gears at both relatively low speeds and highway speeds, so there's no pattern there. There is no check engine light when this happens, but I have not yet attempted to check codes just in case it might be storing any. It'll happen when the engine is both cold and at normal operating temperature. I've also tried to observe whether or not the tachometer drops when it bumps, but haven't really been able to discern that due to the usual momentary nature of the power loss.
The coil on this car is integrated into the distributor and I read somewhere that it's common for these to start to go as these Camrys age and accumulate a lot of miles. I also read that it's common for these cars to hesitate due to internally leaking fuel pulsation dampeners. The AC compressor makes a little noise, and sometimes it almost feels like what you would expect it to feel when the compressor kicks on, although the jolt or 1-2 second sustained power loss, depending on what occurs, feels stronger than that. Plus it'll do it with the AC off, so that doesn't seem to be a possibility. Other than this problem, the car has no issues whatsoever. It's quiet, uses very little oil, idles perfectly and maintains optimal operating temperature. The miles are about 75% highway since I've been using it mostly as an airport commuter car. Most essential maintenance items, such as the clutch, timing belt, water pump, oil seals, PCV valve, thermostat, radiator, motor mounts, etc. have been replaced within the last 15K miles, and most are Toyota OEM parts. Plugs, wires, cap and rotor have all been replaced within the last 10K miles, again with Denso plugs and wires, but aftermarket cap and rotor. I did feel up under the distributor and got some fresh oil on my fingers, so the o-ring might be leaking a bit. However, I don't know yet if there is any internal leakage inside the distributor itself.
I'm going to tear into it a bit, but I wanted to see which direction to look first. Would you suspect a spark issue (again, no CEL illuminates), or something more like a fuel delivery issue? I also wondered if it might be something like the TPS or perhaps a cam or crank position sensor on the way out.
View 10 Replies
I have a problem that has being going on with my 2000 toyota celica gt has been sputtering/jerking when going at a constant speed of about 60 mph. The problem is interment. I have changed everything from cam sensor when it came up on the scanner. Also changed the fuel filter and fuel pump. I changed the spark plugs. No luck the problem went away for about 2 weeks when I changed the fuel pump and filter but it came back. I got it scanned and the only code that comes up is P0420 which is a catalytic converter code. I have no clue where to go from here.
View 9 Replies
I have recently had about $1620 worth of work done on my 2000 4Runner because the check engine light came on and the code was P0420.. My invoice says they replaced the exhaust pipe assembly. Now 2 weeks later the light is back on with the same code...are the 02 sensors part of the "exhaust pipe assembly" or are they now going to tell me I need a bunch (2-4) 02 sensors replaced.
View 3 Replies
2002 4Runner 4x4, 180K miles. I bought this car about a year ago and don't know anything about its history before that but it seems to be in good shape.
About every month or two I take a trip that includes driving a few miles on a dirt road. It is a graded road in pretty decent shape. What has happened about 6 times during the year is that the CEL comes on while I am driving on the dirt road. The car continues to run well. When I get home and hook up my code reader the code is always P0420 Catalyst efficiency below threshold.
To save everyone the trouble of looking that up, this code indicates that either the upstream or downstream A/F Ratio sensor is bad. If both sensors test good then it is probably a bad cat.
What is different here is that after I clear the code, the CEL stays off as long as I stay on paved roads. So to summarize, I don't get the code every time I drive on a dirt road but every time the CEL has come on it is while I was on a dirt road.
So it seems that something about driving on a dirt road causes the CEL. Two obvious things you get on a dirt road are dust and vibration. What could be causing this? I did a visual inspection of the whole exhaust but did not see anything obvious such as cracks or leaks.
And of course I could live with this if I have to since it comes up under such limited circumstances. I just like to keep my cars running properly.
View 6 Replies
My 2006 Sonata V6 (88k miles) has an occasional power steering loss. It has only been noticed right after slowing down from highway speed. Total loss for a few seconds then comes back. No dash lights or noises, just cant steer - then can. Did all required maint. until 60k then just oil changes by me. Have read other forums about fluid flush, but that was for noise and I don't have any noise. This has happened with and without the Electronic Stability Control turned on. Other than that, runs great. MPG is about 25 or so (wish was 30 or so).
View 9 Replies
2006 Toyota Camry LE (4 cyl) with 149,500 miles. All maintenance up to date.
Over the past month, anytime I drive over 80 mph within 15 minutes, the CEL comes on with the code P0420. I read the code and erase it. The funny thing is typically I'm getting very good gas mileage during that tankful when the CEL comes on. I've read that it is likely the downstream oxygen sensor and I plan to replace it. (In February, I replaced the air/fuel sensor). My two questions are:
a) What is the part number for the oxygen sensor (non-California emissions)? I want to make sure I get the right part.
b) Why the CEL comes on after travel over 80 mph? Is this coincidence or is there a reason why this happens?
View 14 Replies
I have a 2003 Toyota Corolla, mileage app. 106,000. Check engine light first came on when driving to destination 40+ miles away (most of my driving is shorter, around-town trips). My mechanic said code is P0420 and so they reset it and said if it comes on again that I need a new cat converter. It did not come on until about 6 weeks later when I was on a longer trip again (had driven about 40-50 miles). Can you tell me if the P0420 code absolutely means that a new cat. conv. is needed or if it could possibly be a sensor or something else hopefully less costly than a new cc?
View 3 Replies
On my 2006 Camry, my ABS comes on intermittently when braking (~5% of the time) and the speed is very slow (5 mph or less). Exact speed is hard to say. I think one of the ABS sensors is misreading. No ABS fault light on dash.I have an explanation of how to check the sensors for AC voltage when spinning the wheel using a DVM.
1. Without a lift can I check this under the hood instead of at the wheel? Possibly at the plug into the ABS module.
2. Someone else on another thread mentioned that their dealership hooked in a monitor and drove around.
When I asked my dealership how they would diagnose this, they said they would do the same check as I mentioned above (#1). This would be expensive and since it is intermittent, they might not see anything. Do this monitor exists and what it is called?
View 13 Replies
2003 Camry 2.4L 4cyl
I noticed my engine light turned on. I went to Autozone to hook the car up to the computer. The computer printed out the code P0420. My coolant temp is normal. What can this code mean. The car has over 126,000 miles.
View 14 Replies
I have a 2002 sienna that will lose power to radio, air conditioner, power windows, surges when going down the road. So far it only last for a little while. And for a while now there has been times y…
View 2 Replies
My wife was driving yesterday from work and suddenly felt the steering becoming hard to steer so she was able to drive home but barely made it to our driveway (very hard to steer). I saw fluid dripping down the right side of the car. I opened the hood and saw lots of brown fluid spilled all over. Power steering fluid reservoir was empty. So my question is, is this primarily caused by power steering pump failure causing spillage of fluid contaminating the drive belt causing it to slip (car overheated a little bit) or Serpentine belt failure (120,000 miles with original belt) causing power steering pump to fail and eventually leak fluid.
Photos: [URL] .....
View 6 Replies
P0420 bank 1 code popped up while driving. Im thinking this is just an oxygen sensor? Is it ok to drive with this code for a while if i buy an o2 sensor online?
View 5 Replies
1989 Camry, 2.0L A/T- 97K mi.- This car has developed a violent shaking condition when traveling at highway speed. It only occurs after the car has been driven for at least 1/2 hour. It does not appear to be related to an individual wheel or axle, and happens only when the accelerator pedal is depressed and the car is in gear and moving at 50+ MPH. Steering is not affected, nor does turning the steering wheel increase or decrease the shaking. The shaking stops when the accelerator is released. The engine runs smoothly, with no misfire or vibration.
View 3 Replies
Problem I'm having, when in overdrive my 04' F150 FX4 5.4 Triton surges while trying to maintain a steady speed during power delivery to the wheels, it causes a shuttering and bucking effect. If I push the button to turn the O/D off, the RPMs rise and problem goes away. During the problem no CEL illuminates and tach stays constant. Fluid condition & level are okay. (not burnt) I'm completely baffled since there is no code in the ECM to point me in the right direction. I do use the truck to occasionally tow my 5k lb boat & trailer. When I began towing I did not know to turn the O/D off and put some miles on towing in overdrive, I know now that was not good for the tranny.
View 7 Replies
2006 Toyota Camry 4 Cyl Manual Transmission. I'm getting a PO017 code - Engine Coolant Temperature (ECT) Circuit Low Input.
The dashboard temp gauge reaches a red H at low speeds. After about 15 minutes of driving, the car overheats and shuts down when the car slows down. I wasn't at home and didn't have coolant, so I put water in the coolant reservoir. 15 minutes later at home, the car overheated and shut down. The water in the reservoir was boiling and steaming.
When the car is idle, the radiator fan turns on immediately. I noticed the passenger side fan doesn't run. Could the one fan be the problem?
I was also really low on oil and added oil. There's oil on the engine block too. I might have multiple problems at the same time. See pics. [URL] .....
View 12 Replies
I have a 2006 Subaru Forester with 95,000 miles on it. Earlier today the CEL (solid) and cruise (flashing) came on while I was driving. I believe it may have occurred as I was accelerating up hill. I filled up yesterday, so I tightened the gas cap when I stopped. On my way home, I stopped by my mechanic and they read the code; P0420 Catalyst Efficiency Below Threshold Bank was the code that was read. They reset the code for me but told me that the catalytic converter is what needs to be replaced.
My question: Could the light coming on be incidental (i.e., is it possible that it was a "blip" and my catalytic converter is okay?)? My mechanic said he thinks it is, and that my car should last me quite a bit longer. I am asking because I've put in a bit of money into the car of late and I'm wondering if I should just jump ship. I should say that the majority of the repairs are maintenance (e.g., brakes, tires).
View 8 Replies
So today my CEL came on. I immediately looked at my mileage and I was EXACTLY at 500m past my oil change the other day. I checked the dip stick and lo and behold, it was about 3/4" past the full marker. I took it back to the oil change place and had them drain it down to a good level.
I had driven from NH to NY this week. I filled up my gas tank on my way home from NY. Gas cap was on nice and tight for sure.
The code is still on (not sure how many miles or drive cycles is required) for something to clear. I figured it was perhaps due to too much oil added. I decided a few hours later to take it to AutoZone and grab the diagnostic code. It's a P0420 code (Cat System efficiency below threshold: Air leak in exhaust before rear HO2S, AF Sensor Error, Fuel System Fault, Faulty Catalytic Converter).
View 18 Replies
The power button didn't work for a while: For about two hours, the power button (and other stuff) on my 2007 Prius didn't work. But, after a couple of hours, the button worked again and I was able to power down my car (this after many, many pushes both soft and hard). I've now turned it on and off a few times and the car seems to be OK and it's behaving as if it's smiling at me and saying, "What?"
My questions: Does this happen a "lot"? Would the car have turned off if I turned off the smart function (as described on page 34 of the manual)? Is this issue as serious as it seems? Should I dump the car?
This is the first time in 138K miles that the below issues have manifested separately or together.
Other issues that happened at the same time (this morning when the car didn't turn off) were that the:
Instrument cluster was completely dark except for the check engine light (the dark instrument cluster was what first tipped me off that something was wrong)
Backup camera didn't turn on when I shifted into reverse gear
Phone didn't automatically go to speed dial when I was in motion
Fifth door unlock didn't work; the four doors locked/unlocked using the lock/unlock button on the door, but the hatchback didn't unlock.
A day or so ago, the check engine light came on and is throwing a "P0420" code (I posted about this separately yesterday).
By the way, I found out that if you hold down the power button for a while, the car goes into a different state of being where the ICE isn't running and the battery shows as completely empty.
View 8 Replies
