Camry :: Replaced MC Still Got Soft Pedal?
May 11, 2015
I replaced my MC, and still soft pedal, when I bench bleedI noticed that the screw in plugs to fit the tubes over it to bench bleed it, they both were loose and when I was bleeding it a lot air bubbles was goin thru the tubes, so I tighten the screws and belled it again this time I bleed it till no bubbles, installed the MC and we bleed the brakes, and still soft peddle, we are going o bleed again tomorrow. Were we supposed to bleed until the new fluid comes out? and if you can what is the best way to bleed the brakes?
View 6 Replies
Advertisement
I have an 07 v6 SE with 220k on the clock. Recently switched out my rear pads with no problem, but still had a small shake under braking - so tonight we pulled the front wheels off and switched the front pads and rotors out - did an oil change while it was there.
On it's first test drive - there's something wrong. The brake pedal travels all the way to the floor and is SUPER soft. It still stops. If I mash the pedal, the car will come to a sharp stop - testing on some sandy roads, the front brakes are definitely working - but the front pedal travel is WAY more than it was prior to the pad/rotor maintenance.
We ran out of light, so tomorrow we're going to get some new fluids and flush the system in case we got air in it.
View 12 Replies
Just as the title states. When I put the AC on in the car my clutch pedal gets some play in it, enough that it messes up shifting and gets jerky. I tried searching, but no results
View 14 Replies
Got Elantra GT 6 month ago. Good car, but it seems I have a very common problem of Elantras - lost of brakes. My car has TCS, but no ABS. It started 4 month ago. Car is fine for several weeks, but then within two days brake pedal getting from bad to worse. My mechanic already replaced master cylinder and right rear caliper. Did not work. Yesterday it was third time when I almost (very soft pedal) lost brakes. Today in Hyundai dealer service they bled the brakes and said "that they hope it will work". Their mechanic found air in both (left and right) rear brake lines. So, my question if I have a leak in, say, left line will it propagate to the right line? I am asking because I do not know the hydraulic schema of the brakes and want to collect as much info as possible.
View 17 Replies
We were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?
View 3 Replies
I have had everything related to the clutch changed, and I even had a dealership bleed the clutch line. The problem is the clutch pedal is soft and will sometimes work good and sometimes won't. If I prop the pedal to the floor for a few hours, it works fine for the day. what gives?
View 1 Replies
I have a 2001 Dodge Durang. 105k miles.
Brake pedal is real soft goes pretty far down (close to floor) before brakes kick in.
Check front disc pads and rear shoe pads, both look good. Fluid level is good. Bleed brake lines.
Pump brakes up when car is off, pedal is real firm till I turn car on an push on brake pedal right to the floor.
View 4 Replies
The pedal used to go right down to the floor and would barely stop the car from a crawl, in response I have bled the brake lines to all calipers, and checked the hydro booster fluid level, and with only slight improvement the pedal almost hits the floor.
I am thinking the brake master cylinder is shot. The pedal becomes solid after about 15 pumps when off, and holds pressure, when on it takes several pumps to build any sort of pressure and cannot be built up to the solid point, and looses pressure quickly when just holding the pedal down.
View 3 Replies
My B6 purchased exactly three weeks ago has had a soft brake pedal since day one. By "soft," I mean that when parked with the engine running and applying moderate pedal pressure, the brake pedal provides some resistance but sinks to the floor. If I pump it up a few times, it temporarily gets much firmer, but eventually sinks to the floor again after a few seconds. Now the car so far has never failed to actually stop, and it can get into the ABS. But during an abrupt (okay...panic) stop last week, it did go to the floor while the car was still moving. That's when I decided that was enough and took it back to be serviced.
My expectation was that there was just a small amount of air in a line somewhere, and that they could bleed the system and fix it. That was my experience with my B5: it was very sensitive to the least little bit of air, and if it wasn't thoroughly bled after brake service the pedal often got mushy and could find the floor. But bleeding them always get the pedal back to normal. So the service advisor said that he "had the service manager drive [my car] and compare it to a new Passat [on the lot] and talked to "Quality Tech. Manager to confirm." And the confirmation was that my brake system is "working as designed." In short, they say the brakes are working properly and there is nothing to fix. So I have now picked up the car and it still does the same thing.
Now I can (and will) bleed the brakes on my own over the weekend. But I would like feedback from others as to whether or not their brake pedals regularly see the floor. I just can't see this being the way any hydraulic brake system should work..
View 21 Replies
I keep finding air every time i bleed my clutch. I am not losing fluid but i can not figure out whats causing my problems. The pedal is soft at first and then gets harder and it sometimes needs pumped before i change gears or to even get into gear. I am afraid its the slave but i also just may have air in the system.
View 8 Replies
Purchased new 2012 Ford F350 to haul slide in camper. When I step on the brakes they go 3/4 of the way down. If I pump again, they go 1/4 of the way down (normal). Brought this to Ford dealer, they test drove the vehicle and admitted I had a problem with the brakes. They told Ford and Ford faxed a letter stating they are aware of this issue and there is nothing they can do about it. Stated this is a "soft braking pedal problem" with some of the 2011 and 2012 Ford trucks.
View 5 Replies
I have a Hyundai Santa Fe 2005 2.7L 4WD ABS.
The problem is that the Brakes pedal is so soft, that it goes to the floor, and doesn't brake at all in first pedaling. I am able to apply brakes after pumping the pedal thrice in continuation and then when it builds up some pressure, then it brakes and I'm able to stop the car. Once, I take the foot out of the pedal, it goes bad again. Once, again if I have to apply brakes, I have to do 3-4 times pedaling.
The brakes are stopping the car fine when they get applied in 3rd or 4th pedaling and when pressure is built up. Its the pressure not getting built up or maintained in the first go.
What has been done by the mechanics to solve this:
1. Master Cylinder has been replaced with a new one. (This has been done twice)
2. Brake Pads have been changed.
3. Brake fluid has been replaced and is upto the brim in cylinder reservoir.
View 7 Replies
I have a 2005 Santa Fe 2.7 V6.
For over a month I have had a soft brake pedal. For those that may not know what that is, I push my brake pedal down 3/4 of the way, and I'll finally feel the brakes catch; however, I cannot stop quickly. I have had to use the Sports Mode to slow down my car many times.
I brought it to my local mechanic and he has done the following:
1) he thought it might have been the master cylinder, so he replaced it. he checked the old master cylinder and found nothing wrong.
2) bled the brake system a couple of times, but it still came back
3) brought my car to the local dealer to drain the ABS system. The problem still came back.
I waited over an hour as the dealership's service department checked out the car. Someone finally came to me and said they checked the lines and they are not leaking, so it has to be the master cylinder. I told the guy that it's a brand new cylinder, and when the mechanic looked at the old one, he said there was nothing wrong with it. All he could say was it's not the lines, it's the cylinder. If I had the problem before & after the master cylinder was replaced, & nothing was wrong with the original master cylinder, how is it the master cylinder?
I called my local mechanic on my way home from the dealership and told him what happened. He said he was going to do some research, mentioned something about replacing something with the ABS and he would call me today.
I searched the forums for brake issues and saw something about cracked ABS rings. Could that be an issue? Could it be something else?
View 21 Replies
Just the other day I got the clutch replaced on my 06 WRX. I took it to a reputable workshop that I've dealt with before. When I got it back the clutch pedal feels very soft and goes to the floor with ease, whereas before it was a lot harder and felt good. It works good and dosen't slip but just a soft pedal. I also went for the OEM replacement and not aftermarket. Some of the google searches I've read say the pedal will get harder after about 1000-2000 km.
View 5 Replies
Soft Pedal. 2004 Santa Fe, front wheel drive 4cyl, 2.4l
When I first owned this Santa Fe the brake pedal was high and had lots of stopping power, over the last few years I noticed the pedal was getting lower. I have replaced everything needed thus far including pads, rotors and everything has recently been serviced front/rear/emergency brake/ calipers and still a soft pedal. Had the guys in our recon shop replace master cylinder and bleed the lines a few times with a full week in between bleeding to ensure there was no air in the lines. The mechanics are stumped but I'm wondering if we missed something...... I still can stop no problem but there is no grab in brakes until pedal is half way down to the floor or worse.
View 15 Replies
I changed front rotors and bled brakes. They were hard for a few days and went soft. No leak in fluid (MC reservoir is still full). No leak in fluid near any wheel. Could I need to bench bleed the master cylinder?
View 12 Replies
I got the attached warning today on my 2010 LS600. The pedal felt a little soft after the warning. It kept popping off and on, dinging every 30-40 seconds.
I checked the brake fluid, it was full. Car has 36k
I had it towed in to Lexus and they couldn't get the warning to come back up.
View 4 Replies
We have a 1997 Mitsubishi Eclipse with a hydraulic clutch. The pedal is very soft in the morning and requires a good bit of pumping the pedal to get good pressure. I know the system needs to be bled. Does this mean one of the cylinders is bad? I have added a little bit of fluid over the last year- maybe 2 or 3 ounces total. Right now the fluid level seems fine but it still needs to be pumped before driving.
View 7 Replies
I have an Imola 20th and recently i have been having some problems with my clutch. The pedal goes from being soft to very hard when its close to disengaging. It also engages very heavily when I go to let it out. This only started happening recently when temperatures started to drop if this has any effect on a clutch. Also, I replaced a shift fork two months ago and was curious if there was possibly anything going on with seals around the slave cylinder.
View 2 Replies
I have a 2000 Grand Prix 3.8 with 65,000 miles. Bought the car new for the wife to drive. The front brake lines rusted out. My wife has a friend who is a backyard mechanic. She had him replace the front brake lines, from the abs block to each front wheel. Well she finally told me that the brake pedal is not right. I went out and sure enough with pressure on the pedal it goes to an inch off the floor. I bled all for lines at each caliper, no change in pedal. I bled almost a full bottle of fluid. You can pump the pedal for 10 minutes and no change in the pedal. I don't think it is air in the line. I changed the pads and rotors on all four corners last fall. The brake pedal was normal then.
View 5 Replies
Here's the short of it. 3rd time in a year the brakes on my 2005 SF (177K miles, 2.7L) have gone out.
The brake pedal is very soft and goes to the floor before braking occurs. Typical signs of a bad master cylinder.
The first time was a year ago. I bought a re-manufactured master cylinder, change it and bled the brakes. Worked like a champ and lasted 10 months.
To months ago same exact symptoms. I assume it was a bad re-man part. It's under warranty, not big deal. I do warranty exchange, bleed system, brakes return. All is good.
Less then 3 weeks later, brakes gone, same symptoms! This time I spend the difference and get a brand new OEM cylinder with reservoir. Replace, bleed, problem fixed. Brakes go out in less than a week.
I'm not leaking anywhere. Reservoir is to corect level. ABS light is NOT on. No chattering in brakes. Braking is smooth both when power brakes work and when not. No visible damage to calipers. I'm 99% sure there is no air in the system, but I'm going to try bleeding again. I have not put it up on a lift to yet to check all the lines.
View 21 Replies
