Caravan/Voyager :: 2000 / 3.0L - Engine Shuts Off When Drive Up To Traffic Lights
Sep 9, 2012
Dodge Grand Caravan 2000 3.0L
First, sometimes the engine began shuts off. When the drive up to the traffic lights. When sharply throw gas pedal. When the engine speed is less than 2000. If you release the gas pedal, you will see that the tachometer needle drops below 500 rpm and the engine stalls. This happened happened two or three days all right. And sometimes a day, 3-4 times shuts off. Then ringing under the hood.
Was the flywheel. I remove the transmission and replace the flywheel. More repair parking brake pedal. So it turns analyzed under the panel. I have a new problem. After repair. I driving my Dodge week. And once. After an overnight stay the machine, on morning the engine not start. I checked the spark. The spark is. I removed the fuel hose. and there is no pressure. Just a little bit of fuel.
I decided that this is the fuel pump. I took off his tank, bought a new fuel pump. The pump has not changed. Today I decided to apply voltage to the old pump, it still stands in the tank. It works. Buzzing. Then I decided to check the voltage on the connector. I turned on the ignition. The instrument appears briefly on 12 volts. They are only momentary. Now I think there should always be 12 volts? Fuel tank removed. All hoses are disconnected. Not really the problem in the fuel pump? How to troubleshoot? Where can I get the wiring diagram?
View 2 Replies
Advertisement
I have an engine noise on my 2000 Dodge Caravan with the 3.3 engine. It sounds a lot like the grinding of a rotating part. It occurs at start up, momentarily, then goes away. If I drop it in gear and start doing low speed maneuvering in the driveway, it comes back. If I turn on the AC it comes back. In all cases, the noise goes away at around 1200 rpm.
The noise occurs again, when I shut the engine down.The engine performs and runs smooth and normal otherwise. No stalling, stumbling, or bad gas mileage to report.
I can "feel" the noise with my hand, when I put my hand on the ac compressor bracket, or the intake manifold, or the valve cover. I've tried the listening through the stick method, and it seems to be coming from the front area of the engine. But I can't be sure. It is something internal. Let me describe:
I thought it was my AC compressor or clutch going bad. The fact that my AC had stopped working well, and was making jet engine noises at high rpm supported me decide this. I replaced the compressor. The AC works great now, and the jet engine noises went away. But the grinding noise is still there. As described.
I wishfully thought it was the belt tensioner or idler pulley. I replaced both of those. Noise still was there. I pulled off the serpentine belt, and started the engine. It made the noise, very briefly as it started, then went away completely. It made the noise again briefly as I shut the motor off. So it's still there without any of the accessories turning.
The noise is loud and obnoxious at idle when under load. It just can't be good. I've read theories about similar sounding problems, saying they could be loose timing chain, bad oil pump, slapping pistons, crank journals, flexplate/flywheels cracked.
I'm going to try doing an oil system flush, and then I'll change it out with a little thicker oil. See if that makes any difference in the noise. Currently I'm running 5w-30 Mobile 1. I think. I'll let you know if it changes anything. I'm also thinking I want to make a short video of the car idling and making the noise for my video camera. I'll post that on youtube and link it here.
View 12 Replies
2007 Grand Caravan SXT, 86K Miles
Factory Radio Clock, AM/FM, CD and Tape Player.
Radio and Clock looses power and completely shuts off and will not turn back on while driving. Miles driven does not seem to be consistent.
All other Electrical seems to work fine, overhead console, Wipers, Blower, Turn Signals, Head Lights, Instrument Panel all seems fine.
When car is shut off, Blower continues to run for a few seconds and then stops.
When car is restarted Radio/Clock magically comes back, clock is reset to 12:00 and radio is on AM.
Get some funny flashing of Idiot lights on cluster that to my recolection is not normal behavior. Once while my wife was driving it the Vehicle Theft Alarm Light came on when she started it up and it stayed on until she stopped and then started it back up when she left the store she was at. That has only happened once.
I checked the Battery Voltage while running and stopped and all seems normal. The Battery was new this December. I also checked fuses and there are none that are blown.
View 1 Replies
A few weeks ago I took my 03 Caravan to a shop and they said my alternator was fine, but the Wal*Mart battery (which I assume is a piece of rubbish) reads a bit low. When the temperatures are about 25 Fahrenheit or below the engine will sputter a bit usually at stop lights and the headlights will dim then go back to normal brightness a few times.
Now that the temperatures are in the 40s-50s I am still having this problem, but not as pronounced and sometimes it happens rather randomly. There is now another problem to go along with it. If I have the steering wheel turned hard while backing up and am not pressing the accelerator I have almost had Edward (my name for the Caravan) stall on me instead of just sputtering. Sometimes I feel like the engine is surging a wee bit as I drive down the road if I have just let off the accelerator. In general the RPM seems a bit erratic at times.
The fuel economy is the same as ever, the belts are all new over the past year, spark plugs, and all that. Recently replaced the vacuum plugs where the cruise control would go as well.
View 4 Replies
When I drive through large puddles, or in the rain, my car doesn't turn. I believe this may be because my Splash Guard is missing.
I keep looking online to get a replacement, and they have one that looks exact, and another I have no clue if this would be the same or if it is a different piece all together.
The picture attached at 1.jpg is the one that looks exactly as the one that is gone from my car.
The second, is the one that I keep finding when I type in replacement splash guard.
Can this one be a proper substitute?
View 1 Replies
My 4 cylinder Tacoma vibrates a lot when it is idling, especially sitting in "drive" at traffic lights. My regular mechanic has tried various things to remedy it but none has really worked. He suggested the valves may need to be adjusted. Is this plausible? Or is he off-base? And is it really expensive?
View 4 Replies
I have a 2006 Grand Caravan 3.8 that just stalled at a set of lights yesterday and have had it towed back to the shop here. I turns over and starts briefly then will die and then just turn over strongly. I cleaned the throttle body and IAC but this did not work. I connected fuel pressure tester and have no pressure when turn key on or turn it over.
The fuse and relay check out ok, so I'm thinking bad or clogged fuel pump.
I have a 2004 Caravan out back that I have used for other small parts to interchange before and was wondering whether or not the fuel pumps between these two are compatible. Be a lot of work to pull the one off the one in the yard, only to find out its not going to fit.
View 3 Replies
I just replaced the transmission in my 2000 3.3L Grand Voyager and now it won't start. It started fine when I drove it into the shop. The battery is good, the cables are ok. The starter worked good up to this point. I checked all the connections to make sure they are tight. I replaced the transmission because reverse went out.
When I turn on the key, the shift letters (PND32) appear on the instrument panel, but the little circle that shows what gear it is in does not appear. When you turn the key to the run position, the circle should be around the P to show it is in park.
When I turn the key to start, nothing happens. No clicks or anything. The next thing I am going to do is see if there is power to the starter when the key is in the start position. Where to start looking?
View 14 Replies
Just changed the battery on a '98 Grand Caravan 3.3. In the process of tightening the positive terminal I accidentally touched the wrench to the negative. There was a spark, of course, but otherwise no biggie. However, now the HVAC indicator lights, including the rear wiper, defroster, etc. indicator lights, all blink continuously until about 15 minutes of driving, then they return to normal. I disconnected the battery thinking that I needed to clear the PCM but the blinking always returns. Is this some sort of manual code reading deal? If so there's no mention of it in the Haynes manual.
View 14 Replies
My wife has a 2000 t&c with 150k on it its a fwd with 3.8 and about a month ago while driving we noticed the rpms will jump up 400 and go back, with cruise control on or off being held at a consistent speed. and about for days ago it started shifting late. Still has all gears fluid looks o.k. and is full no check engine light .
I am hearing transmission solenoid, tps sensor, input sensor, output sensor, tcm, iac, map, or egr are all possibilities or a rebuild . Or simple as a flush.. tonight i went out n started it it idles around 800 tried to hold it at 1200 and it would for a second and drop back to 800 with accelerator being slightly held. Not sure if related. Just observed it..
View 2 Replies
My 2000 dodge caravan with the 3.3 is shuddering while in gear and not moving especially in reverse . As soon as you start going it stops . No slipping whatsoever. The van only has 130'000 miles on it .
View 2 Replies
My van just started to have this issue today with jerking real hard like its dropping a couple of gears while going between 50-60mph. It is a 2000 with the flex fuel 3.3L 4 speed auto.When this happens the spedo will go from 55mph to 40 instantly while keeping a steady speed and it feels like the tranny is going to rip right out. This will happen every 5 to 10 min but go back to normal driving after 3 sec and has not popped any codes. It runs like a top and all fluids are at the correct levels. I have to commute 50 miles a day to work so i really need to figure this out!!!
View 1 Replies
My GC is overheating. Started as occasionally but now increasing in frequency. I find it will being to overheat after driving on the interstate for half hour or so but I can "calm" it back down but turning on the heat. I've replaced the following:
1. coolant (no drips or leaks nor am I losing coolant over time)
2. thermostat (twice)
3. temperature sensor
4. serpentine belt and tensioner
5. radiator (last summer)
6. water pump (last winter)
I notice the fans run more often than they should. For example, after a 10 minute ride to work in the morning,. I notice the fans are running as I pull into my parking space.
View 14 Replies
Drivers side not bowing hot air? We changed the blower motor and the resister on the passenger side. We hadn't tried to use the heat until last night when we needed the defrost and that's when we realized only heat on passenger side.
View 1 Replies
I had a VERY bad leak, to the point where I would fill it, an hour later it all leaked out. I had a mechanic work on it, and he rebuilt the PS pump, BUT the pulley was cracked, they DON'T make that size anymore. He put a bigger one on, only to find out, it was rubbing on my brake lines so I couldn't drive it! SO I had another grease monkey work on it, went through a few new pulley's FINALLY found one! BUT went through 4 Serpentine belts!!
After 3 months with NO VEHICLE, we finally got it all back together. BUT now it is not all lining up we couldn't tell until we had the belt on. it is about a 1/4 of an inch to much to the right.
I'm thinking maybe washers or spacers would work?
View 4 Replies
So my radiator fans were staying on until my battery died and my car was completely cooled down and off. I was told it was a sticking relay so I replaced it and the fans still won't come on. I unplugged the coolant temp sensor and the fans came on so I know its not the motors or anything.
View 5 Replies
I have a 2000 Dodge Caravan. The power lock switches are no longer working (both driver and front passenger). They worked fine the last time I drove the vehicle and both switches stopped working at the same time. The power locks themselves still function with the remote and still lock when speed reaches 25km. Just the actual switches on the doors are not functioning.
View 5 Replies
I recently had 2 coils replaces and 4 spark plugs (CODES SHOWING ACCORDING TO GOODYEAR) replaced because the engine light was ON. Now My car intermittently shuts off without warning, but will restart about 1 or 2 minutes later showing CHECK GAS CAP on dashboard. Went back to Goodyear thinking maybe faulty parts. They ask if any lights are on like the check engine light, they tell me if not they don't know, come back if it continues. I thought maybe it's my battery.
The guys at Battery Bills connected a devise to the battery that shows green if it's charged, YELLOW if it needs to be driven more(or issue) RED(not enough power PROBLEM) and I when back to them yesterday and they rechecked...Battery is fully charged. They said the alternator is good also, I'm not too sure they checked.Later after work I fuel up a the Chevron instead of Costco thinking maybe the gas??? My car starts then dies, the battery signal device is showing red.
I get a jump, the second the cables are connected to my battery the device shows green, my car starts right up. Pull out to the traffic light, car shuts off, but restarts. I was told to drive my car at least 30 minutes away from home and back about once a week, to keep battery charged because I live less than 10 minutes away from wherever I drive to....so I DRIVE about 5 minutes in my car starts to stutter(hesitate) twice, but smooths out and I also notice the RPM gauge is showing 0???? NO ERROR LIGHTS or CHECK ENGINE ARE SHOWING ON THE DASHBOARD so I continue home at a lost. My car is a 2010 Accent with 57,100 miles....
View 7 Replies
I purchased a 2004 Chrysler Town & Country Dec 2003. I noticed an intermittent problem with my gear shift indicator lights PDRNL were all lighting up when I would start the vehicle in February 2004. I would have to play with the shift lever a few times to get it into gear.
On Feb 26, 2004 the vehicle would not start at all, would not even turn over. The vehicle had to be towed to the dealership. It had 3500 miles at the time. The error code was PO706 check shifter signal. They said it was the transmission range sensor and replaced it. I had no problems for 2000 miles until I was in northern Michigan and the gear shift indicator lights started doing the same thing.
I brought it to a local Chrysler dealership the next morning and they scanned the following codes PO1791 loss of prime PO705 check shifter signal BCM stored TCM message not received FCM stored TCM communication fault DSD stored incomplete power voltage. This dealership checked connections and wiring harness which were okay so advised me to take it back to my dealership at home since they would have to tear the whole van down to figure out what was wrong and any parts they would need would not get there before I left for home.
Luckily, I made it home with only one incident with these lights coming on. My dealership had the same error code PO706 and also PO444. Here is what their repair order states "DTC PO706 shift signal fault. Front pump allowing torque convertor to bleed down IPM internally shorted causing intermittent shift signal errors and PO444 and PO706. Scan and perform trans diag and fluid level full R & I the transmission R & I the pan and valve body replace the filter R & I the front pump and replace the front pump and torque convertor called STAR about intermittent loss of shift signal was told to replace the IPM. Replace the IPM (power distribution center) retest ok at this time."
So here is my question....I am very worried with all that I am reading about transmission problems and this van has only 6500 miles and all these parts that they have had to replace already is really scaring me!
View 14 Replies
I'm having trouble with my 2000 Grand Caravan 3.3L. The gauge cluster was working intermittently & recently quit. I have the P1698 trouble code & looked up info online. I of course found out about the solder joint problem & figured that would be the culprit. I took the dash apart & found the solder joints were fine, but when coming apart, the wire plug on the back side came out on it's own. The retaining clip was broke & I thought maybe that was my problem. There's enough room to install a zip tie to hold the plug in & I put it back together. It still doesn't work though.
Here's the symptoms- I turn the key to ignition & nothing in the instrument cluster comes on. When I start the engine, everything lights & works as normal except for the trans indicator- the letters light, but no position shown (regardless of any gear selection). This continues for about 5-10 seconds & the trans position indicator lights up around EVERY letter. A few seconds later the entire dash goes down. I then shut off the engine by only turning the key back 1 notch. At this key position the odometer & trans indicator come on & the trans indicator will properly display every selected position correctly. It is consistently working this way every time now. The heat is also stuck on hot & the rear window wiper/ washer is not working.
I've also pulled the body module to check for connection problems & don't find anything with that. I've pulled the fuse under the hood too. So far no luck.
View 4 Replies
I have a 1993 Cadillac STS which I just purchased with low miles and clean carfax. Local car. Everything works like a dream and drives beautiful. All of the sudden it just shuts off ()Northstar engine() and I have to place it in park and start it again. It usually just happens on slow traffic. No engine service light so I can't get the auto shop to get me an error code. What it might be?
View 16 Replies
