Corolla / Matrix 2009-13 :: Small Vibration On High Speeds When Hit 80km/h
Jun 15, 2015
So when i hit ~80km/h (50 miles) some weird extremely small vibration is coming on. You cannot feel it from anywhere but when u touch something, like handbrake then its there. Tho the sound is kinda loud. So the pattern is like, 0.3 seconds it is vibrating and 0.3 is quiet, it does not matter on which road i drive.
This problem cannot be caused by wheels (got other alloys and same problem), also already got alignment and have balanced my wheels. So, what to do?
View 10 Replies
Advertisement
Ive been using synthetic 5w-20 for about 7k miles on my 09 corolla s, has hit 100k. Was looking under the engine and small amount of oil on the drain plug. I had the drain plug replaced about 15k miles ago and not sure if thats where its actually leaking from.
Should I switch to high mileage oil? Ive used 5w-30 high mileage awhile ago to go with the good ol oil consumption with this year engine and didnt like the dip in mpg's and felt like the car couldnt run as well as it should. I switched to synthetic to take better care of the engine after using high mileage for about 6k miles.
Question 1 - Should I switch back to high mileage?
Questions 2 - Should I use Lucas oil leak product? (I use the gas cleaner)
View 8 Replies
I had some issues over the past couple of days with my 2009 Corolla EPS. It would occasionally go off, after all the indicator lights would flash momentarily. This only happens at low speeds, under 10 mph, and as soon as I got it up to speed the power steering would come back on. (note just about 140,000 miles)
I took my car into the dealer and he told me my battery needed to be replaced, its the original, and my rear hub and bearing assembly is corroded and there is electrical damage back there.
Did my first repair this summer, the alternator and water pump. But I didn't think the rear hub and bearing would have electrical connections or sensors effecting the EPS. I'm sure there is rust, but would that cause EPS issues? Could there be electrical damage? I also tested my battery yesterday and got 12.5 - 12.6 V with if off and 13.6 -13.7 on, but my battery is old.
I am going to pick it up from the dealer and just try changing the battery first. The total repair they suggested would cost $1875.00, which is crazy to me? Could there be a bigger issue though, and could the EPS just cut out on me while I'm on the highway or something?
View 2 Replies
2011 Corolla S, the RPM's drop by couple hundred suddenly when easing off the gas pedal. This is more noticeable at speeds of about 60-70mph. I got it checked out under warranty and the dealer said it is normal as the car shifting out of overdrive.
They may be correct in this as it is the speed around which the overdrive comes into play but it just does not feel right, although it may be related to the overdrive, they should have a fix so that the car slows down gradually, not suddenly.
I have read other TS-B updates which resolves the problem of fluctuating RPM's at steady speeds or the RPM not dropping when letting off the gas pedal, however my issue is slightly different in that the RPM's drop suddenly and then jumps back up again. I wonder if that same TS-B flash will resolve my issue.
View 5 Replies
I have a 2010 Model S that has 38,000 miles on it. I am hearing a rattling in the front brakes when cruising along at almost all speeds. If i hold a little peddle pressure it goes away. Sounds like the pads are rattling to me. I am running the stock pads with about 45 to 50% remaining on them.
View 6 Replies
I just bought a 2002 corolla with a salvage title. I am having trouble with the front passenger side vibration at high speeds 50mph on up. It had the vibration when I bought it and I put 4 brand new tires on it, and had the front end aligned and had a fellow mechanic look at it and and said everything up front was tight. The guy I bought it from said he had the front brakes just done but I feel a pulsating as when I apply the brakes. My fellow mechanic said he would turn the rotors next week, my question is what would be my next step if that not it, axle? I really wouldn't car but I drive this car 150 miles a day to work and its all highway.
View 2 Replies
Recently purchased my first Toyota, a 2012 Corolla S with 76,000 miles on the ODO. I have a concern about a front end rumbling.
First, the problem...
This "rumble" (the best way I can describe it) starts becoming noticeable around 20-25 mph, depending on the condition of the road I'm on (it could be lower, but I'm in Michigan, all the roads are bad here). This rumble isn't a noise, but more of a low frequency sensation that can be felt in the car and through the steering wheel, and vibrates the rear view mirror. The rumble comes and goes, it isn't constant. Sort of like driving over a rumble strips put on roads before stop signs/intersections, it seems to have an oscillation to it. The rumble intensifies very little with speed. It doesn't seem to oscillate any faster or rumble much harder, it's just there.
Things I've ruled out...
Brakes. When I bought the car, the first thing I noticed was that the front brake rotors were slightly warped, so I installed new rotors and good pads. That didn't get rid of the problem, though I didn't really expect it to.
Tires. The previous owner had seriously over-inflated these tires. Once taken down to their proper pressure, they were noticeably cupped down the middle. These tires were also horribly noisy would not balance, so brand new tires went on (Michelins). The new tires greatly improved the ride, reduced noise, and got rid of a lot of other shakes and vibrations, but the "rumble" remains.
Wheel Bearings. I'm not 100% on this one, but as far as I can tell, it's not the wheel bearings. I've taken the car out on twisty roads and there is no change in the rumble through hard turns, nor any additional vibrations of any kind. Usually bad wheel bearings will exhibit some noise or vibration when being loaded in a turn, but not in this case, so I've ruled them out.
Things I'm not sure about...
CV Joints. I've never had a CV joint go bad or fail on me, so I am unfamiliar with the common signs and symptoms. I have inspected the boots, and they appear to be in good condition and crack free, though that doesn't mean a joint isn't failing. There's no clicking during slow sharp turns, but I think that would only present itself if an outer joint was failing. I'm going to get the car in the air this weekend to do a drain and fill on the tranny (the fluid is getting pretty dark, so I want to get some new in there).
I drove a Ford Focus for the past 10 years and a Ford Contour for 10 years before that, putting over 200,000 miles on both, and never experienced any sort of problem like this.
View 8 Replies
Is this behavior normal: I test drove a 2010 corolla LE with 4-spd auto, 41K miles. Noticed that on level highway 60 mph that whenever I eased up on the gas that the RPMs would shoot down. Vehicle speed was barely decelerating since I was on level. As soon as gas reapplied (gently), then the RPMs would shoot up. I'm guessing the delta was like 300 RPM. I get the impression that at highway speeds the car is mostly in 3rd gear or shifting up and down a lot. I've read a lot about a TSB for 2011 corollas but nothing for 2010. And I think that problem is different. So my question is whether this is "normal" for driving at highway speeds?
View 5 Replies
I've owned this vehicle for the past year. This 2009 Corolla XRS manual has a very annoying steering rattle which took me the whole year to finally breakdown and diagnose. There are many forums stating this rattle is associated with the intermediate shaft assembly #2. I did end up replacing this part 45260-02110, hoping this would fix the rattling or knocking issue. It did not, but smoothness the steering has improved. I removed the upper portion of the intermediate shaft to pinpoint the sound. Originally I believed the noise may have been coming through the bulkhead from the intermediate shaft #1 or steering rack. I checked under the boot and everything was snug. Then I rattled the steering wheel around and this what I found.
It seems the noise is coming from the pinion where the power steering motor meets the steering column. You can hear the knocking noise with settle steering wheel movements. As I move faster, the knock turns into a rattle at higher speeds most likely vibration from the road. At this time, I do not want to disassemble the whole column just to see if I can adjust the motor height (if possible).
YouTube : [URL] ......
View 6 Replies
My wife's 2009 Corolla S has 107,000 miles. Early on it developed a low idle and vibration while stopped at a light. It was idling about 600 rpm after it warmed up. It never stalled but occasionally vibrated. After doing some research I found some were having success cleaning the throttle body and throttle plate. I did that along with changing the spark plugs. At that time I disconnected the battery to reset the computer. She has put about 2,000 miles on it since then and it never idles below 800 rpm. The vibration hasn't been back either.
I believe it was the throttle body/ plate cleaning and disconnecting the battery that resets the computer that fixed it. The plugs still looked good at 105 K miles, but I had new ones so I put them in. I bought a can of Berryman b12 choke & carb cleaner and sprayed a little on the throttle body and plate and then sprayed some on a rag and wiped down the body and plate. It was quite dirty.
View 14 Replies
Basically when the car is in D and when i am stopped with the brakes pressed on at a stop sign or a red light, the car starts vibrating and i can see the the rpm going down and then receiving back up and going down again something when the car is in R. its a 2009 toyota corolla le 90k miles. when the headlights are on, the rpm stays high so the car does not vibrate or anything. other than this the car runs perfectly fine.
View 1 Replies
Recently, my 09 corolla S starts shaking during slow moving . As I accelerate more, it start vibrating at high frequency. And I can hear the sound "kin kin kni.." I checked the tires, they all look fine. It has 60k miles on.
View 2 Replies
I will most likely be driving my Corolla to Colorado this summer and I plan on attempting several 14'ers. I know you can almost drive to the top of Mt Evans which is over 14k. Driving that high in Corolla, how was the drive up?
View 5 Replies
year: 2009
miles: 80160
This usually happens when im on the highway i guess because im usually going over 50mph I hear like a loud humming and vibration and if I turn the steering wheel left or right it becomes unbearable, like deafening. What may cause this, im thinking maybe i need an alignment or wheel balancing or just new suspension.
View 2 Replies
2010 Corolla 1.8 automatic. Accelerating at highway speed (2800-3200) rpm a low frequency shudder/vibration is felt in the floorboards. Goes away of you let up off of gas pedal. No vibration at idle, runs fine all other times. Most noticeable when accelerating under load (ie going uphill) and at highway speed. Trans mount visually intact. Ditto engine mounts. Cv axles less than 1 year old no rattle upon shaking.
View 5 Replies
I think I resolved the idle issue on my 2009 Corolla S with 82,500 miles and Automatic Transmission.
Symptoms:
Idled at between 600 and 800 rpms
Annoying vibration in drive and reverse, no vibration in park or neutral
On hard stops, the engine felt like it was going to die
Turning on the a/c would cause the idle to increase to 1000 rpms and the vibration would go away.
At 82,500 miles, I cleaned the throttle body which was extremely dirty.
Process:
Disconnect the positive battery cable
Remove the top of the air box and flex duct going to the throttle body
Disconnect the two coolant lines going to the throttle body, make sure and have a few old bolts to plug the lines so you do not lose too much coolant
Remove the electrical connector to the throttle body
Remove the vacumn line to the valve cover
Remove 2 bolts and 2 nuts (10mm) securing the throttle body to the intake.
The throttle body does not have a gasket, it is an o-ring which should be fine.
Once you have the throttle body off of the engine, clean it thoroughly with Chemtool throttle body cleaner.
The inside of the throttle body and throttle plate should look like shiny milled aluminum. when done.
Spray chemtool into the two ports where the antifreeze lines were connected. If possible use compressed air to blow out these ports.
Clean the inside of the intake and the mesh screen where the throttle body bolts to the intake.
Reassemble, connect the battery, crank the engine and just let it idle for a good 10 minutes
The 2009 Corolla S DOES NOT have a serviceable IAC. It is riveted on to the throttle body. This is why it is important to spray the cleaner in the antifreeze ports in order to clean it. These ports are the antifreeze bypass ports.
View 2 Replies
I am getting a engine vibration on a new 2011 corolla LE. The vibration is right between 2000-3000 RPM. Also the muffler kinda sounds louder at that RPM. I have only 300 miles on this car ...
View 14 Replies
This vibration with sound on my brake pedal started after i change my stock intake to takeda. Well, Not all the time this thing happen, only when im in this kind of situation:
Pressing and hold my brake pedal at full stop and the gear is set to Drive, then, when the RPM goes down to below 900, the vibration with sound started, and it only disappear when i release my brake or when the RPM goes up automatically.
But, this only happened with this kind of situation when my car already heated up (like driving it more than 10 mins) and the temperature is at stable level.
While my car is just started driving, or its not already heated up, no vibration is happening.
View 2 Replies
2011 Corolla LE. Recently I upgraded the air intake, look at the picture
Shortly after that both me and my wife noticed that the brake pedal vibrates while car is In stop on lights. The vibration is only on the pedal and if you press it hard you suppress it. But when you feet is pressing light in the air it's very noticeable.
She also thinks that during above scenario RPMs go from about 1000k to 900 so are dropping. To be honest I did not notice that and not sure if this is normal or not. Other than that the car runs great and sounds much nicer bit loud but I like it.
View 4 Replies
I have a 09 Corolla with low mileage (33,000 miles). It drove without a problem until recently.
About 1 month ago I started noticing some rattling noise at high speed (>50 mph) coming from the engine compartment on the passenger side. the noise seems to get more frequent the faster i go and disappears when the speed drops below 40 mph. It is not loud but still noticeable. The car itself does not shake.
I drove through a snow storm before the noise happened. not sure if this has any thing to do with it.
View 2 Replies
I'm new to owning a Toyota. I just financed a 2010 black Toyota corolla S with 36 miles on it from a local dealership after i decided my last car was pretty much a money pit (2001 expedition)...blew the head gaskets, then after that was fixed developed a bad knock...anyhow i just decided i was overdue for a new car. Its a 5 speed manual and at highway speeds (65-70mph) I've noticed the rpms are bit high...like around 3grand. Is that normal? Just seemed really high to me, I really think this car would do great with a 6 speed. Also is the corolla governed? I was on a long stretch of road and i quickly got to 110ish with no sign of a governor kicking in...?
View 14 Replies
