Elantra XD (2001-06) :: CEL / Codes P0705 And P1529 - Car Jerks Into Reverse And Drive
Mar 26, 2015
I have the following codes:
P0705
P1529
It looks like P1529 is caused by P0705. P0705 is the neutral range sensor. I purchased the sensor and replaced it. It is aligned correctly and I am still having the same CEL and codes.
What the car doing: The car jerks into reverse and drive. The dash does not indicate what gear I am in (PRNDL).
When it drives, acceleration is very slow. I believe the car is "stuck" in third gear. I've heard of fail safe mode?
What I did: This problem started when I changed my stereo. I did three bad things which may have caused this problem.
One, I had to put the car in "L" to get the dash off. I left it in "L" for a while then I tried starting the engine while it was still in "L".
Two, when I reinstalled the center console I swapped the wiring for the hazard lights and the rear windshield wiper (GT)
Three, I wired the dash illumination positive and negative together.
The cluster's backlight does not come on anymore and these codes came up. I checked all fuses and they are good. Where to look for a possible shorted wire that can be causing this?
View 10 Replies
Advertisement
Elantra GT 2003 ... I had engine check light on and OBD 2 code reader showed DTC P1529 and P0705. I erased the codes to see if they comes back and one month later I have same codes back. P0705 indicates Transmission Range Sensor Circuit Malfunction, so probably I should check range sensor. How the range sensor looks alike and where to find it. Where can I find it?
View 1 Replies
I have a 2001 Elantra GLS, 160,000 miles. These two codes come up on ny diagnostic tool.
P0422
Main catalyst efficiency below threshold (bank 1)
No symptoms at all
P1529
Customer snapshot request
Symptoms
Car will shift hard into third gear and stay there without shifting at all regardless of speed. Shutting the car off and restarting will sometimes fix, but only temporary. When car runs normal, it runs fine and shifts good. At speeds around 40 it seems to kick back and forth between 3rd and overdrive as if it can't decide where to be. Tried replacing speed sensor, but new sensor did not fix problem.
Fuel Sys 1 CL
Fuel Sys 2 NA
Calc Load 18.4
ECT 201
STFT B1 0.0
LTFT B1 -2.3
MAP 8.6
Eng RPM 3351
Veh Speed 22
EV flashing
O flashing
View 17 Replies
I have a 2001 vr6 Jetta automatic transmission. When I shift my car from park into to reverse or drive the whole car jerks as if it's banging into gears. But while driving it drives normal. When I stop and accelerate I feel the same jerking you would say.
View 5 Replies
I have a 2002 SF GLS/LX (?) with 2.7 L V6 2WD (60,000 miles) and it started to apply the ABS brakes in a random manner. Found out it was caused by a broken front wheel tone ring. So, I pulled the ABS fuse under the dash and it stopped the brake problem. Drove it today to pick up some wood and now the check engine light has come on.
My neighbor has an OBD scanner and he plugged it in and said I have a P0501 code and a P1529 code, but he didn't know what they meant. What they mean and are they related to me pulling the fuse under the dash? Did I pull the wrong fuse? Is there another fuse somewhere that I should have pulled?
View 1 Replies
I recently bought my '05 Elantra from a small dealership and I'm starting to see a problem with it. If I shift into reverse and then go back into drive, the car doesn't go forward at all. I have to mess with the gear shift a bit to get the car moving. I'm pretty sure it's a bad linkage. The dealership I bought it from said it desperately needed motor mounts when they got it so they replaced 2 of them. I'm sure the problems are related. I can't find any information on replacing it myself though.
View 1 Replies
I've hyundai elantra 2013 while changing gear by car jerk and sometime it doesn't jerk. What is issue causing car to jerk when changing gear. It happens not every time, sometime it don't jerk while changing gear.
View 1 Replies
Ok, so this past week i towed my 72 f250 to IL from CA. 2100 Miles. 6100#s with the trailer. No problems at all. Got about 9 MPG too the whole way. Ok, so here is my problem now. As some of you may know, IL just got about a foot of snow. Its all slush at this point. I am living in the country right now so i drive thru alot of it. Ok, now you know the back story, today i drove the truck to my brothers house, put it in park and bam! check engine light came on. About a half hour later i drove it to AutoZone and had them check the codes. Here is what they pulled.
P0705
P0171
Need to know what to replace. I have to drive it back to CA in 4 days.
View 1 Replies
Below is a link to a video showing what my 2003 Hyundai Elantra is doing. It is idling very rough (Jerks at idle) and can actually be heard in the exhaust. I think it may be miss firing?? Does not do it at speeds over 60. Under 60 it can be felt at times, but only at low RPMs. [URL] ....
View 16 Replies
I am the second owner of a 97 Cherokee 4.0 2wd. My overdrive works now and then. my check engine light is on. I had it scanned it throws 2 codes. p0700 and p0705. It has 147k and we already replaced the entire cooling system including flushing the engine and system thoroughly . Now it has been sitting for nearly 2yrs. just not sure what direction to go.
View 3 Replies
2002 7.3 4R100 ... The truck started flashing the O/D light pulling a 9K lb trailer on the highway.
The transmission codes read were P0705 (Range Selector) and P0873 (bad 3-4 shift - RPMs did not drop).
On the highway, the TCC seemed to lock up fine in 4th (OD button was set to leave O/D ON). When the truck would downshift (not often) then it would sometimes would rev high when it downshifted. It was like 3rd was slipping or it was downshifting into 2nd instead of 3rd. I think it was doing a 4-2 downshift but not 100% sure.
What confuses me is that if it is doing a 4-2 downshift then it would have to change state of both valve body solenoids. Is it possible that it was doing a 4-3 shift but solenoid was sort of sticking? Trans fluid looks fine.
I have read other posts where people had same problem (titled 3rd gear slipping), but they never seemed to resolve the problem in the thread. How likely is it that the solenoid is the problem? It seems to drive fine in 3rd when the O/D OFF button is pressed and O/D is not allowed.
View 6 Replies
I have a 2008 Elantra GLS. I am getting a code of P0750. Seloniod A fault. I have checked wiring harness for critter bites all looks good. If I clear the code the transmission shifts normal until it is shut off like overnight. I also have been noticing that it idles around 1100RPM to 1300RPM and it does drop into gear harder (reverse or drive). This high idle started before the P0750 code.
View 4 Replies
I just started hearing a loud click when I change from park to reverse and from reverse to drive. If I keep moving the knob between those three spots with my foot on the brake and hand brake off, I hear a loud click at each spot. Hard to describe... anyway, this only happens when I first start the car, by the time I get to work if I try doing that when I park there is no loud click sound. The thing is, I don't know if this was always happening and I just noticed it now, or if it just started.
View 14 Replies
I have an Elantra 2012 sedan GL and last year i tried installing HID's. It worked for a whole but then it stopped after. I learned that it wasn't getting enough power so then yesterday I bought a wiring kit to be able to wire my HID to tap to the battery to get more power. Everything was fine till I got to work but when I had to leave work., there was an issue. Whenever i switch the gear from park to drive or reverse or neutral. My car seems to jerk. And when I'm driving and it changes gears, it also jerks. Kind of the same thing how if your driving a manual car and you change gears wrong. This happens when my lights are off. But when i turn them on it then stops. And when i turn it back of it doesn't do it anymore.
View 5 Replies
For a few months now I have been hearing a tap clunk type noise coming from under the car when I shift the auto trans into drive and reverse. Also sometimes when the car is slowing when driving I hear the tap sound as it shifts into first. I drove in by my local dealer and they listened to it and said Elantra transmissions can get noisy there is nothing wrong. They told me I have plenty of Warranty left so if something happens I will be covered.
View 2 Replies
My 2001 Prius has 77K. It has done warning lights before and always been a gas cap that was not tightened or a misfire code three times since I bought it last spring. It has been driven very little when I was rear-ended and my Camry was totaled. It coughed a little when I started it, but had no problem driving the first 40 miles. I stopped for about 5 minutes to stretch. When I tried to start it to continue to work, all the warning lights came on and it died. I tightened the gas cap and restarted the car to have it die 2 more times. Third time it stayed on and I was planning on limping two blocks to AutoZone to have the codes read, when it rolled to a stop. No forward, no reverse. By the time the tow arrived, it would go forward. The codes were P3101 and 12689.
View 4 Replies
I have 2001 ford explorer sport.. it idles very low in drive and reverse and then shuts off.. What has been replaced:
1. Torque converter
2. All new plugs n wires
3. Map or mass sensor
4. Iac valve
5. O2 sensors
6. Fuel filter
7. Air filter
8. Throttle valve/sensor
It does not run bad only when u come to a red or stop light.. Had the vacuum tested and no vacuum leaks.. also no check engine light has come on and no codes have popped up when tested..
View 1 Replies
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 Replies
My 2003 Santa Fe makes a grumbling noise when first started, and put into drive or reverse. The noise seems to be coming from the passenger side of the engine compartment. The noise disappears when the drive train has warmed up.
View 4 Replies
2004 Santa Fe, clunking noise in drive or reverse. checked brakes and cv joints, replaced drivers front and still making the noise. Transfer case was a little low on fluid but not much. Put up on stands and turn wheels with no noise. Put in drive or reverse while in the air and rear wheels sit still. It is a 4wd so I would think that all 4 tires would be turning. While in the air the front both turn and no noise is made.
View 18 Replies
Recently my 2004 Santa Fe 2.7 AWD (~86k miles) has started to give a sort of hard thump when shifting from reverse into drive. It's fine going into any other gears and it shifts up and down normally. If I shift from reverse to neutral and then to drive it's fine.
I changed the transmission fluid when we first got the car at 40K miles with Hyundai Liquid Unobtanium SPiii fluid and again at 80k miles with Valvoline's SPiii offering. I just checked the transmission fluid level and it's within the normal range.
I can't tell if this is just drive-line slop or something else inside the tranny.
View 2 Replies
