I've replaced the fuel pump and filter, plugs and coolant temp sensor. It starts after I spray starter fluid in after a few times and cycle the key on to prime the line but is still hard to start. It runs fine and it seems that as long as the engine is warm or (guessing) fuel is still pressurized in the line it starts fine.
View 3 RepliesWe have a 94 ford explorer and every now and again it has issues on the start up. It will sound like it will want to crank over but just won't. If we wait 20 mins it will start up no problem. We have changed the fuel pump, fuel filter, ignition coil, and fuel pump relay but it still has this problem. Also occasionally the a/c blower wont turn on. Tonight it happened again and I pulled the fuel pump relay out and it was really hot, after it cooled down and was put back in the car started. I am beginning to think it maybe an overheating issue that is affecting the relays but am not sure. I was also wondering about changing out the relay box...
View 6 Replies2002 4.6L 75K Miles ... Truck has hard time starting if it sits for a few days. Recently had the fuel filter (under driver's door) replaced for first time, and mechanic said it was clogged (?). He also checked fuel pump pressure and said it was good (about 40 lbs). Truck starts OK if used every day. Battery seems OK, as starter turn engine fine. Seems that there's a fuel problem.
View 4 Replies2001 F 350 7.3 183,000 miles.. The problem is the longer it sits the harder it starts.. when it does start it runs VERY ruff!!! it takes 10 min or so to run on all cylinders.... This is my first diesel..
View 4 RepliesThe car has 96xxx miles and doesn't like to turn over when it sits for more than about 6 hours, it is worse the colder it is. Once the car starts it will fire right up every time you start it as long as it doesn't sit for more than about 6 hours. It doesn't make any strange noises while starting just the normal vum vum vum vum VUM vum vum VUM VUM vum vum etc until it finally catches. I should also add that upon starting (and this only happens when it hard starts) it will idle at around 1500rpm while in the park. The shift to reverse it drops to about 1000, shift back to park it goes back to 1500. I have already replaced the fuel pump, 02 sensors, MAF, and the camshaft position sensor. I took it to a shop once, they could not figure out the problem but claimed it was a common problem with Nissans of that period and if I primed the fuel pump by turning the key to the ACC point for about a minute and pressing the gas a little bit when I tried to start it that it would start. That does not work.
View 2 Replies1994 Explorer V6 100,000 miles, it is getting fuel and spark. After driving for a short/long period the engine will turn over but won't start. If you floor the gas pedal it will fire up, with a small puff of black smoke out the exhaust. Fuel pressure regulator came first to mind, and has been replaced. Problem was cured for a few days, then it started again.
Next Idle Air Control solenoid. Replaced, with same results. Replaced EGR position sensor. This worked for a few weeks. Then starting issue came back. Then I was told to replace fuel pump relay. This was the last part replaced. It had been running great. Started warm without any issues for a week. But now I have a check engine light and hot start problem again.
If the gas is floored the truck will fire. If gas is not floored the engine keeps turning and turning. I am sure it is not a fuel pump problem, as there gas fumes and the tailpipe is black. Could it be Mass AIR FLOW ?
Sometimes after running my 94 Limited, it doesn't want to start - it does crank - like it's not getting fuel. I have found the work around and want to know if it would be fixed by replacing the fuel pump relay.
The symptom is just after starting, it starts to run poorly, and then dies out, then will not start at all. I use to keep trying to start it for 20-40 minutes and suddenly it seemed to work.
It seems the work around is to turn the key to on for about 5 seconds and then turn it off - then it starts and runs as good as ever.
So, is this a symptom of a bad relay? I thought I'd start there because of the cost of the relay is fairly cheap. 1994 Explorer Limited 4x4?
I have a 1994 Ford Explorer XLT. It just died the other night. I have dim dome light, nothing else. I had the battery and alternator tested, both are ok. I get an occasional click when trying to start it. I also get an occasional beeping, the key in the ignition sound. I've checked the fuses, and can't find a broken one.
View 3 Replies1994 Ranger .. Last wednesday I had to get a jump because the lights where left on. Everything was normal on thursday. Friday morning. I went to go start the truck and notice that it would try once to start and then try a second time and it would start. Today I was driving it. The check engine light came on and when I get the RPMs up to shift up, I would loose all power and have to wait till it gets down below 10mph before I would get the power back.
View 8 RepliesIt is a 2006 Explorer with the 4.0 and around 89,000 on the odometer. Around a couple weeks or so ago the wife said the explorer was hard to start one evening and it has been like that ever since. It cranks for about 5 seconds and then fires. So far it has started every time since this issue began. This is really the first issue we have ever had other than the radiator replacement a few years ago.
View 3 RepliesHard start like it's not getting enough fuel then kicks in and runs great with no hesitations or issues and with plenty of power. Replaced fuel filter, nothing changed.
View 3 RepliesYes, another thread on an explorer that occasionally has trouble starting. One cold morning the fuel pump would not operate. When turning the key to run the volts to the pump (with plug disconnected) was 8.6 for a second, then dropped to the 6v range. I took the inertia switch from the firewall and back probed the wire going to the fuel pump, getting 12 volts. I went back to the fuel tank and measured the voltage with the key in run position, and read battery voltage. The car started, and has not failed in 3 days. I know it will quit again. I was thinking of replacing the inertia switch and fuel pump relay.
View 5 RepliesI am having a random hard start condition. it will happen once a week or with no rhyme or reason. It turns over real nice but does not start until the second or third trythe last time on third try i push accel pedal to floor and it started. This hasn't happen in a few day so I cant tell you if the accel pedal will always work.
View 9 RepliesI have a 2005 Ford Explorer 4wd with 4.0 SOHC 6 cyl Flex Fuel. For months the vehicle has idle rough and increasingly becoming difficult to start. I decicded to replace the spark plugs and wires hoping to solve this issue! gap set to 052. When I started the vehicle it went into engine fail safe mode and wrench light came on. I then replaced the TPS on the throttle body and had no diference (I may have installed incorrectly! when I put it on the armature felt like it broke free inside the sensor). DTC codes read P0223, P2106, P2110 and with P0122 pending, P0223 pdg, P2106 pdg, & 2110 pdg.
With the old tps installed and wiring harness disconnected the truck will start in fail safe mode, but will not start at all with wire harness connected. A volt meter reads at computer end of wire plug 3.69 volts at pin one (gray/red wire +) and pin three (gray/white wire -) with key to on but not running.
After sitting engine cranks longer than it usually did before it starts. idles a little rough. engine light comes on after it been running about 30 sec for 1 min. after that seems to run fine.check codes po446 and p1633 always come up. if you let sit a bit with key on starts right up.replaced gas cap checked evap lines, and changed filter no luck. Did notice with lines off evap solenoid key off or on i can blow through it. that doesn't sound right.
Checked fuel pressure. key on jumps to 90psi then falls to 55psi and stays. turn off key and leaked off 10psi in 5 min.start engine while watching gauge does the same as when the key on except it falls to 30 to 35 psi and bounces between them. i think this is way low. What is the correct pressure? Shut off engine and drops to 20 in 5 min. Next I plugged line on test tee going to fuel rail and tested same results as key on. the convinced fuel pump was bad since regulator and check is there. replaced pump. problem still there.
Here are my xj specs:
All in standard condition..
One day, I just changed my battery..suddenly my engine get hard to start... Got missfire too... I just change my distributor rotor, plug n wire plug... Why this happen? Now it just crank and cannot start...
i have a 1994 mitsubishi diamante 3.0 sohc hard to start and idles real rough. it has new plugs,wires,cap,rotor button,fuel filter,and air filter.fuel pressure is between 45 and 50psi which is good i have good compression on all cylinders timing belt is good and i am getting spark to all plugs. with the car running i pull the plug wires off and cylinders 1 3 5 makes a difference but 2 4 6 their is no change.the car was setting for two years.it dose have new gas.the check engine light is not on and has no codes.
View 2 RepliesI'm a diesel mechanic and know my way around Powerstrokes, this 4.0 is not what I would usually work on, but I have a friend who has 2006 explorer 4.0L SOHC, someone told him he needed a motor with out explanation why, so I didn't want to see him get ripped off. The problem is it idles very rough, hard to start, and stalls. There's no DTCs , if you hold the accelerator slightly it will stay running, but once you let off it will either idle really bad and misfire or cut off, once pushing the accelerator the rpms raise very smoothly up til 3500 which is what I assume the rev limit is in nuetral.
I've done checks with focom and forscan, I was thinking possibly a bad fuel pump, while monitoring fuel pressure I see a range of 289 - 326 kpa with 26% fuel pump I guess duty cycle would be the correct term(once again I'm a diesel guy, and use to dealing with IPRs and Hpops) not sure if the desired fuel pressure is relevant on these but it always stays at 269kpa. I believe that equals out to 40-48psi while I believe this system is supposed to have somewhere in the range of 60 - 70, but I wouldn't expect to get a rough idle with no load with almost 50 psi of fuel pressure.
So with no DTCs Im baffled, and don't want to start wasting money just throwing parts at it. I've thought everything from fuel pressure sensor, to coil pack(replaced 4 months ago) to crank and cam sensors.
I did end up getting a code p106, but I believe this is because I didnt tighten the intake hose after checking the throttle bottle, I just slid it back on. out of the 4 days of testing first time I seen a code pop up besides unplugging some sensors here and there to make sure the pcm would actually register a dtc.
I have a 2000 Explorer W/4.0 SOHC engine. With summer nearly over and fall on the way, I need to figure out what is going on with my engine. This problem has been going on for the past 2 years. As the outdoor temperatures get cooler, the harder it is to start and keep the engine running. This starts happening around 65 ambient temperature, and gets worse as the temps drop. By 30, I can barely keep the engine running.
Odd thing is, all I have to do if the engine starts is, keep my foot on the pedal to keep the engine around 2000RPM, put it in gear and start driving. After about a mile or two, the engine runs normally, and will do so the rest of the day. So far I have cleaned the air flow sensor, replaced the IAC, replaced all the injector "O" rings, and cussed a lot. I smoke tested the engine and the only vacuum leak is a very small one at the EGR valve.
I just got this truck. 1999 F250 4X4 with the 5.4L. It will start great when its cold but after you get it hot and it sits for a bit it will not start (will crank) again till it cools off. Its has new MAF coil packs and plugs, air filter tranny flush and oil change.
View 2 Replies2000 2WD 4.6L ... I was trouble shooting why the truck will not start after it has run for awhile then sits for about an hour. I was checking the connections on the solenoid switch on the fire wall when my wrench slipped and touched both terminals on the solenoid and the engine starter kicked in. I tightened the connection then tried to start the truck with no luck. so I tried leaving the key in the "ON" position and jumped the two terminals and the truck started. Does this tell me I have a bad solenoid switch?
View 6 Replies