Ford 6.0L Power Stroke Diesel :: 2004 - Crank But Won't Start?
Mar 11, 2015
2004 6.0 truck ran fine parked it, went out next morning and has been a crank no start. Brand new ficm put in today. Also scangauge readings while cranking.
IPR DUTY 30%
ICP -1000+
ICPV-.2 and rises
FICM-49.5 Never drop below 48
FICM LOGIC-11.5V And it also drops to 9 volts cranking
FICM SYNC-Yes
CAM/CRANK SYNC-Yes
I can here fuel pump running and have checked the bowl and fills in 3 second, also have held valve down in oil filter housing and it fills up in 4 seconds. Oil level perfect half tank fuel .. Also I get no smoke from tail pipe while trying to crank. Acts like it not firing or has no fuel... Driving me crazy been working on it for three weeks.
View 13 Replies
Advertisement
I have a 2004 6liter. I parked one day two weeks ago and a went out last week to move it and I will only crank over. No fire No start!!!! Have new batteries. New fuel filter and have fuel coming in to the fuel bowl. I have gone over the harness, checked my fuses. I do not have a reader or scanner. Any recommendations. I want more than just a code scanner.
View 14 Replies
ok, so after all the work done (headgaskets, head bolts, egr valve, ipr valve, egr cooler, oil cooler, blue spring kit, new ficm injector harness connectors), this is what I'm left with on start up. I am now getting no SYNC -0
I had ficm sync before i changed the connectors on the injector harness (last thing i did besides blue spring kit). Has this motor turn this way? And my glow plug light now comes on during and post crank along with a weird fuel light with 3 teardrops I've never seen before. I need to check this out.
48.0 ficm KOEO, 48.3 crank
IPC 3 KOEO, 1100 crank
IPR 14.1 KOEO, 46 crank
IPC volt .23 KOEO, 1.23 crank
Passed bubble test
View 14 Replies
Just installed lots of new parts on this late 04 6 liter HPOP, Stand pipes, nipple cup orings, head gaskets. and now she wont go. Just cranks. Doing an air test now, should I be able to hear anything form the oil fill tube? It builds oil pressure just not right away, I did have an icp code. but has gone away as of now (p2285). What's consider a long crank time?
View 3 Replies
I have an early 2004 F 250 6.0 that just quit one day and haven't been able to get it started since then. I have tried to follow the No Start checklist...
I have no aftermarket mods or tunes.
I have changed the fuel filters, made sure that there is fuel in the tank and made sure that it is getting fuel.
I have un-plugged the ICP and still no start.
When I turn the key on it goes through the regular sequence and I hear the injectors (sounds like it's doing a buzz test).
When I try to start it, it cranks over, but I hear a good bit of clicking coming from the fuse/relay panel under the driver's side dash.
I have inspected fuses/relay and dont see anything smokingly obvious.
I installed new batteries, but no joy.
While trying to start, it sounds like it may actually do it for a second, and then I get a noise from the starter.
I bought a scanguage and added the PIDs that I found searching through the forum and here are my results.
ICP key on = 0.23 ICP while trying to start = 1.30
ICP Voltage (Volts)
TXD: 07E02216AD
RXF: 0462451606AD
RXD: 3010
[Code] ....
Camshaft & Crankshaft Sync = This is erratic; it will flash 1 and immediately go away. The thing is, I don't know which sensor should be replaced.
View 4 Replies
I have a 2004 f350 6.0 powerstroke i recently fixed a oil leak in my remote oil cooler and after I was finished it ran fine and ran fine for a few days I noticed yesterday it had a bit of a rough start and some today but would start and run normal. Started the truck this morning and drove it a bit and then let it sit while I went to the dentist came back out and truck wouldn't start. I am getting 200-330 icp with the ipr cycle at 88.5 ficm sync is good and colts are at 12.5 unplugged icp sensor to see if it would start after that and it disnt start so I ruled that out.
I'm currently waiting on AAA to bring my truck home for me but trying to make sure I'm right to start working on it tomorrow. I am thinking the ipr valve is clogged. Am I right to think this may be the issue? When I first installed my remote oil cooler I had the same issue crank no start turned out to be the ipr valve was gunked up and I ended up replacing it 300 dollars later. Then it started and everything was fine. So basically am I right to start at the ipr valve or should I start somewhere else?
View 14 Replies
I've got a 2004 6.0 4x4 broke down in Gillette WY that will crank but won't start. We've had a cert. Ford mechanic bring out the computer first time it showed the IPR valve so that was replaced. Now it's not throwing any codes. We had it running for about 2 hours a week ago but the next morning it wouldn't start again. We're at a loss of what else to check. Here's what we've checked & replaced so far:
2 new batteries
New ICP Sensor
New IPR Valve
New #6 Injector
New Cam Sensor
Checked all fuses and relays
Oil is good
Coolant is good.
High pressure fuel test checked ficm 48 volts as it should be.
It's not the hpop because oil pressure stays up when cranking for fifteen seconds.
Cleaned secondary filter housing.
All filters are good.
Checked fuel pump it's good. ....
View 6 Replies
I have working on this one for a while ( sick wife keeping out of garage for some time) Truck fires up in the morning when cold then refuses to start when warm. Of course HPOP leak. HPOP was replaced 5k miles ago. Now today when I drove with AE connected truck all of sudden started to run rough on the highway. I pulled DTC P0279 low circuit for injector 7. My question is can the leak be at injector 7 on the oil rail? Maybe cracked injector? Waiting for the motor to cool so I can do pop off valve cover . BTW early 04 .
View 13 Replies
2004 6.0 Truck has been slow to start and sometimes took a few tries to get it to fire up. On monday the Truck would not start. The FICM was not getting sync. I figured it could be a bad connection to the FICM. I pulled the FICM, cleaned the contacts and reconnected it. The truck fired up. It ran all day Tuesday without incident but wednesday morning it would again not start. Again what was missing was FICM sync. This time disconnecting and plugging back in the FICM did not fix the problem. I have spent the last two days troubleshooting and am out of things to try.
The problem as it stands right now
The truck will crank but not start. Scanner says it has oil pressure, a steady 48v (FICM has new power supply). The IPR sits around 50% when cranking at 1200psi. However, the FICM will not get sync. I have worked my way down and tested both the Cam and Crank sensors from the PCM. The Crank sensor has a resistance of 360 ohms and produces a AC voltage of 500mV when cranking. The camshaft sensor produces 100mV AC when cranking (camshaft sensor was replaced as the original produced AC voltage seemed low 20mV, new sensor produces 100mV). I have tested the camshaft sensor at the sensor and at the PCM connector. This has lead me to believe both the cam and crank sensors are ok and their signals are being probably transmitted to the PCM.
I have tried to check the inputs to the FICM to confirm the signals are getting there. I was unable to find a good pin out diagram for the 2004 FICM but what I found told me the crankshaft was pin 5 and the camshaft was pin 10. When cranking, pin 5 (crankshaft) did not produce a signal and pin 10 (camshaft) had a 200mV DC signal. Despite searching I have been unable to find what the input signals to the FICM should be.
Right now I suspect bad wiring between the PCM and the FICM, or a bad PCM. This is based on having good signals to the PCM, but (what I think may be) a lack of crankshaft pos. sensor signal to the FICM. I am specifically looking for what the crank/camshaft pos. sensor signal at the FICM should be, as well as confirmation/disconfirmation on the diagnosis of bad PCM or PCM-to-FICM wiring
Truck Details
Ford F350 King Ranch 2004 6.0
Truck build date 11/18/2003
350,000 km
Studded
New FICM power supply
Stock truck; don't run any tunes
View 14 Replies
Powerstroke 6.0 no crank no start... 2004 Excursion. I cannot get any of scanners to connect to get any codes. I have the Autoenginuity Ford Package, scanguage II and another generic scanner. There is power to the diagnostic connector but there is no communication.
I have recently been having issues with rough running cold starts. Codes before this no crank event were 2285 ICP Sensor Low and 0528 fan speed sensor low and one for EGR which has been deleted. Just last weekend I had crank no start. I unplugged the ICP sensor and started and ran. I ordered a new OEM ICP sensor and pigtail and the truck sat until I received them.
Recent Work : I just replaced the ICP sensor and the pig tail. I soldered and heat shrank the wires rather than using the quick connects. I did find that after soldering the pigtail I found two wires shorted on the pigtail. Per the diagram on the 6.0 bible the a/b wires were shorted. I have corrected those. I also noticed that the top of the glow plug control connector has a broken clip. Not sure if there is a connection issue so I have tried to ensure that it is pushed in as far as it will go. I have another module somewhere I'll have to see if I can find it. Replaced glow plugs and harness about 6 months ago.
What have I done:
- Pulled access panel on FICM has 4 posts.
- FICM voltage 48v Key On.
- FICM voltage 46v cranking
Check the diagnostic connector can +/- (pins 6/14) and has resistance 122.1
I've check all the fuses and specifically:
#20 FICM
#22 Engine Control
I found one bad fuse #115 Trailer Tow Charge.
When trying to start Glow Plug light comes on but doesn't go out. The injectors are not initializing and the fuel pump doesn't seem to be running either. I have unplugged sensors ICP, EBP and FSS. Not sure what to test next. I'm considering pulling the ficm harness tomorrow to look for chaffing.
View 14 Replies
2004 F350 4x4 6.0 ... No start... changed fuel pump... lots and lots of bubbles in fuel filter canister.... what to check now... running fuel from external fuel tank not tank on truck... after crank no start fuel disappears from canister.
View 2 Replies
My nephew has a 2004 F350 that will crank but will not start. It will build oil pressure on the gauge. There is no injector buzz and no communication through OBD2 port. Is the PCM dead?
View 10 Replies
I went out to start my truck yesterday which is a 2004 F350 6.0 Diesel. It wouldn't crank over so of course I tried to jump start it and it fired right up. Went to town while I was there got 2 new batteries and put them in went to start truck and again nothing but will only start when jumped even with new batteries I'm guessing there is a grounding out issue. Where to start?
View 1 Replies
The truck was running fine then I shut it off one day and it wouldn't start back up long powerful cranks but wouldn't start pulled the valve covers checked branch tubes and dummy plugs all looked good (not for sure though) replaced the icp and even tried unplugging it after the hot crank no start to see if that worked because that was the only a code I threw but alas it did not work.
I did a air test and closed the IPR valve via fancy tool and was getting some minor gurgling out of the oil filter resivuar and was guided to change the hpop being that was the beloved issue I couldn't get the j-tube out to inspect but everything else was clean as a whistle ... I was getting some air flow threw the oil filler cap and the air intake box on the driver's side valve cover but was told that is normal but not sure how normal when I replaced hpop it appears it stopped gurgling as much.
When I did the following air test but it started when cold but then it struggled but it did start then my batteries died out turns out I do have a bad negative connection I getting the batteries re charged gonna pick them up today and tighten that connection along with a new air filter via reading in the hanes manual that can sometimes cause a hot crank no start .
View 7 Replies
I was driving down the road and suddenly lost tons of acceleration power had to almost flour it to move at all so I pulled off the road to stop and check it out. After I stopped I couldn't get it to start again it would crank like it wanted to start but nothing. So I had I towed home and it sat for a little while and then I tried to crank again, and it started and idled like crap and when I pushed down on the gas pedal there was no reaction, rpms didn't go up or nothing but still would idle like crap.
Symptoms stayed the same for about a day and no I have a crank no start. So then I did what little I could do just to see if it was an easy fix I changed the ICP sensor, IPR sensor, and EGR valve needed to be replaced so I replaced that too. Headstuds and gaskets have been done as well by previous owner but not I think it might be an HPOP problem? I am unable to read codes at the moment as well just FYI. Could this be a fuel filter issue even tho the secondary housing fills with diesel?
View 1 Replies
2003 6.0, all stock. Crank, no start with an occasional sputter when it actually shows FICM SYNC = YES.
It had the following relevant DTCs when I scanned it:
P0261, P0270, P0276 and P0279 - Cylinders 1, 4, 6 and 7 - Injector circuit low
P132B - Turbocharger/Supercharger boost control A performance
P2614 - CMP Open circuit
P2617 - CKP Open circuit
CMP/CKP SYNC transitions to and maintains YES while cranking, however FICM SYNC transitions back and forth between YES and NO while cranking. When it transitions to YES, a cylinder or two will fire when FIPW comes up, but FICM SYNC almost immediately transitions back to NO.
Based solely on the scan tool results, Cranking shows IPR DC at about 50%, ICP PSI ~1500, ICP V ~2.0. These are stable and steady. FICM main power is at 49.5v and drops to 49.0 when it fires the occasional injector while cranking. RPM reads above 150 while cranking.
I'm thinking that since CMP/CKP SYNC stays YES and is stable and RPM reading is consistent, the CMP & CKP sensors and circuits are most likely good. I'm thinking with the codes for injectors 1, 4, 6 and 7 it probably points more toward a FICM issue.
Another thing that may or may not be relevant is the pre-cycle clatter sounds off to me. With an ambient temp of about 70F, the pre-cycle seems to repeat 3 times. The second and third cycles sound worse than the first. This is in the video below.
I work on far more 7.3s than I do 6.0s, so I'm looking for anything I may have overlooked, a second/third/fourth opinion, or if there's a flaw in my logic for someone to point it out.
6.0 No Start - YouTube
View 14 Replies
Brother in law company 6.0 died on him in his driveway after a night of plowing
It stalled out, his boss sent out a "tech" and he said it doesn't have "nearly enough" oil pressure
Now I want to further diagnose the truck myself with my scan gauge II but haven't used it for that......yet......
What should I check for IPR pressure psi or %?
I know I can get ICP pressure in PSI on my SCT x4 not sure about the Scan Gauge......
I assume a blown IPR or failed STC fitting......
Truck is a 2005..... I can figure out the scan gauge I just need to know what to look for for an idea of a blown IPR or STC or ICP.
View 14 Replies
05 6.0 will only start if I cycle the glow plugs, crank 3 seconds shut off glow again then it starts immediately. If I try to glow 2 cycles with out cranking it won't start either. When he truck is hot it seams to start easier. I have new batteries new alternator running 5-40 synth. New glow plug control module. It does it hot or cold weather.
View 7 Replies
I have a 05 with 100K miles on it. I had the HPOP, FICM and EGR delete do about a year ago. Went to start the truck pressed the pedal and it died and won't start. It dies once while driving about a week ago but restarted. I have a Snap-on scanner for the data. FICM tested good and getting fuel to secondary filter. Batteries and filters are new with about 2K miles on them. Would this data point to a bad IPR?
ICP V KOEO = .25V
ICP V Cranking = .28V
ICP_DSRD 1251 PSI Cranking
IPR Duty 15% KOEO
IPR Duty Cranking 85%
View 14 Replies
I had a crank no start with very low hpo pressure. I went to do an air test and could not get my IPR valve to do anything with 12 volts applied. I have a switch wired to it, and went as far as wiring the IPR valve directly to the battery and got nothing. This is a brand new ipr valve, never seen a mile of driving, and I'm wondering if my luck could really be bad enough to get a bad one in the box, or if it could be my truck that's frying them. I have cranked on it a lot trying to start, but I have a feeling this IPR is to blame. I'm on my way to get a warranty replacement now. If my truck could frying them, would that be just a bad ground or what? Any way to test my wiring? I have a multimeter...
View 14 Replies
Ihave a 2008 E 350 6.0 , while driving i hit a small pothole no big deal the van stops running and coasts to the side of the road. get her towed. The dash lights show the PATS is engaged so it is no start no crank.
The 30 amp fuse PCM power relay is blown. when i replace it it blows as soon as i turn the key. im checking for wire chafing but so far have found none.
View 2 Replies
