Ford 6.0L Power Stroke Diesel :: 2005 - Snap Ring Inside Front Hub?
Jun 11, 2015
What is the tool part number for a good pair of snap ring pliers that are heavy duty enough to remove the snap ring from inside an 05+ 4x4 front hub? I have broken two pairs of regular snap ring pliers attempting to remove it. The snap ring itself is roughly 1/8" thick and copper plated. It really wouldn't be that difficult to remove, but that collar on the spline that it has to pass over is thick too and it is whipping me something serious.
View 5 Replies
Advertisement
I broke 2 snap ring plier on this thing, what is the make and model of snap ring pliers used to remove the snap ring off axle in hub ? I have some others but too beefy won't move in there. They need to be long but strong. I've heard Snap On Item: SRPC9000A works but I don't know of any Snap On guys around here and I need to get this thing done.
View 10 Replies
I did some searching and cant seem to find this in a 6.0 (massive results in IDI)
If I rev my truck over about 3200 rpm and release the throttle, as it comes back down to idles it will stall.
Ficm voltage is fine and I am running a stock tune, ICP doesn't seem to drop until the stall...
What should I be looking for?
View 8 Replies
I installed a BPD EGR cooler about 4 years ago just as a preventative measure (along with an oil cooler) in my '06 F-250 6.0. About 6 months ago some coolant was found to be coming down the rear of the engine and onto the garage floor but only in the mornings after cooling down and even then not every morning.
A couple weeks ago I did a coolant flush and put the red ELC coolant in and now I can see better where the coolant is coming from. It appears to be coming out from the O-ring between the cooler and the intake manifold. I did check the torque on the stud and bolt and they are tight.
Is there a way the drop the cooler enough to install a new O-ring with out going through the whole process of removing the intake manifold and everything that is associated with that? The thought is daunting...
View 5 Replies
I am tearing down my junkyard engine to prep it to put into my truck and I came across this on the rear main seal... is this a wear ring?
It kinda looks like a oil slinger. My new seal is on the way so I have nothing to compare it to.
I don't want to be yanking on it if it's supposed to stay.
View 6 Replies
I need to remove my EGR valve to clean the unit of carbon. While there I will be removing the intake elbow to check if I have the throttle plate installed on my engine. What the part number is for the gasket / o-ring that seals the elbow to the intake manifold??
View 7 Replies
Any success story on converting 2003 or 2004 f350 with leaf spring front end to the 2005-2007 f350 coil front end is it possible?
View 8 Replies
I am new to the ford deisel. I have a 2005 F250 6.0 liter power stroke. it has been bullet proofed with EGR delete. Has an after market intake. An Edge TC tuner, and alot of extras. My question is why am I having shaking in the front end when my foot is barely on the gas. If i give it more gas it goes away as soon as the boost kicks up to around 2 or 3. It does this every time I take my foot on and off the pedal. It will only last for a second if i give it alot of gas. But if I barely touch the pedal it will shake the whole time until the boost kicks in.
View 1 Replies
I would like to know if i am the only one that had that problem... a few weeks ago, I had to stop and get the truck towed to the dealership and they told me that my engine was shot. Then they told me it was a glow plug that fell inside the cylinder... didn't know it was possible but any way it was under warranty.
Last Monday they asked me to bring all my service receipt and that ford is asking them to take the engine apart and study it before they would ship a new engine... Are the trying to get away from paying it under warranty? The truck is 2011 with 80000 km (50000 miles).
View 14 Replies
I have a 2004 F350 with 6.0. My problem is the 4x4 will not engage from inside the truck. I have to get out and twist each hub to lock in the 4 wheel drive. If I rev the engine with high rpms the front will lock in with a big jerk. It use to lock in just by turning switch. What is the best way to fix it?
View 5 Replies
2013 f250 6.7 yesterday during drive through heavy rain fall noticed some clean water draining on my bare feet on passenger side of the truck right below glove compartment.
View 6 Replies
I'm sure there is something on this somewhere but can't seem to find. Getting ready to change injector o rings and see where people say to drive it 200 miles to get it running right again. Well, I am in the process of a conversion and have no tags or insurance on the truck. Trying to fix issues before I spend that money on it because don't know how much I am going to have to put in it to fix the issue's.
Is there a way to bleed out the air so I don't have to drive it 200 miles? Also, how long will it smoke after the injector change to see if it is actually fixed? I know I should probably see a big difference is ICP,IPR and such. Already know it has leaks in the turbo up pipes which will have to be dealt with too.
View 14 Replies
I have a 1999 7.3 psd F-450. It's rigged out for welding with a Lincoln SA-200 engine driven welder. My overall weight is approx. 11,500 lbs. and I rarely tow with it. It has a 4 speed automatic and 4.89 ratio gears in it now. I bought it with 245/70/19.5 tires. Stock size is 225/70/19.5. I am going broke trying to keep the fuel light from staying on all the time, and I am considering changing the gear ratio. My questions are; Is this a wise investment, as far as cost vs. gain? I also need to know if it may create a higher risk of other mechanical failures? I need to research what other ring and pinion ratios can be used in the ford 10.5 12 bolt rear axle. Money is hard to come by these days, and even harder to keep. I cannot afford a costly mistake if the funds can be more effective elsewhere.
View 14 Replies
My fuel filter lid o-ring keeps blowing out upon hot start, this has happened 4 times now once last week, I replaced filter and all was ok until Thursday it happens again I change the filter allis fine! Now today!!!!! TWICE I have to install new filters because the o-rings are blowing outside the bowl lid! I'm using the same BALDWIN PF7698 filters I've used for years, my reg. Is set at 75psi and holds steady! No spikes but I haven't been able to watch it when the o-ring blows out! Injectors and o-rings are new (<1000miles) no problems during operation at all!
View 14 Replies
I recently upgraded my exhaust from stock to a 4" Magna Flow Turbo back kit. After the upgrade, I noticed a strange rattle coming from the tail pipe. It sounded like the pipe was vibrating on something but I checked and it is free from anything touching it. There are no strange noises coming from the engine area. it is only herd at the end of the pipe. If I start the truck it makes a the loose rattle noise like something is loose inside the pipe like the sound you get when you have a bad muffler. About after 4 or 5 minutes I hear the exhaust noise change pitch and make a whooshing noise like a gate or something opening or closing and changing the exhaust flow. After a while it goes away and make the loose rattle returns. The truck has lots of power and preforms great. Where to look?
View 3 Replies
Having trouble getting large plastic nut to start threading on top of the fuel tank sending unit, after doing in tank mods.
It just doesnt seem to want to start threading on properly. Its always cocked when it grabs, and after a while opposite side pops up and it falls off. Not sure how to get it back on there
Dealer has new ring for 18 bucks, maybe mine is warped or dried up since 2000?
View 8 Replies
Don't know where to start so I'll ramble!
2005 f350 with the 6.0. Crew Cab, 8' box, 4x4 with DRW. I use it only take the boat to the launch 5 minutes away once in a while and to pull car trailers every other week. Majority of driving is on the highway and average trip is about 300 miles. Low power and now no start.
No codes. I do have a scan Gauge and can provide data.
Was running this week, but has had a lack of power for some time. I had put 2 new injectors in last summer. Also updated dummy and stand pipes. Blue spring. Also new IPR at the time.
Ficm board was replaced in March.
New injector harness last year. New Glow plug harness last year.
Coolant level is fine and none being lost.
CAC hoses appear fine, no cracks.
No boost. But newer MAP sensor, hose not cracked or plugged and nipple on intake is clear. Put the MAP sensor last year and it didn't make a difference.
Turbo was rebuilt 2 years ago.
IPR has to hit close to 80 before boost hits 12-15. But it takes a while to get there.
Now won't start.
Yesterday am it was about 30 farenheit and no start. Last year would start no problem.
Batteries are fine. tested.
Engine fires within 3 seconds, but doesn't want to run.
ICP is above 500. climbs as I turn over.
Fires only in first few seconds and then nothing while I keep cranking it. it is cranking fast enough though.
Now...I see IPR will hit 84.7% and then 14.8%. Not good!
When running it sits in between.
FICm voltage is 48.5 key one and 47.5 when cranking.
Wondering if possibly IPR screen is plugged? Or would CKS or CPS cause issues? I recall reading about pulling one of them and cleaning rust off of it? Also...should mention, no EGR reading on scan gauge..never was either. I had checked and cleaned egr valve before. it was clean when I pulled it and not sticking.
Intake had been cleaned 2years ago. Also, on occasion, while pulling up hill, I would get power! Black smoke and it would race up a hill like it's supposed. Then it would go back to no power.
Also...if I pull the MAP hose from the intake nipple, should I feel suction from the intake? There doesn't appear to be any air coming or going from the nipple.
View 14 Replies
I have 2005 f350 with 365000 km on it I have it for one year and don't have a problem till last week. I was pulling van on dolly uphill and sadden lost pover, so I stopped and check oil leaks ,transmission .... But everything looks ok in couple minutes start engine and go home (10 km). Change fuel filters trans filter, looked good for 50km and star losing power again and doesn't want start. So I skan and its show me next numbers.
Key on engine off
Ipr-15%
Icp-0psi
Icp-.26v
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine crank
Ipr-85%
Ficm main power-48.0
Ficm logistics-12.5
Icp- 625psi
Icp-.77v-1v
So what I have to do?
View 9 Replies
2005 F250 SD, Crew Cab, Diesel 6.0L...
Hauling my jeep (close to 16,000 pounds all in F250+trailer+jeep) on a highway going a little over 70mph up a hill when I seemed to have lost some power and the check engine light came on. The turbo PSI was well over 20PSI (according to the gauge in the dash). I have a Scan Boss but I have not been monitoring turbo boost PSI.
I was only 10 miles from the final destination so I continued without stopping. It seemed that the turbo was limited for the rest of the trip. Later in the evening, no more check engine light but I haven't really driven the truck since then.
What do you think the problem was? What should the course of action be?
View 9 Replies
I had this truck for two months no problems yesterday went on a small trip about 50 miles in on ,the hwy. I start seeing some smoke and then no power turned off & on engine several times a little hard starting no power at all I put the pedal to the floor It barely moves ran into another super d. guy he said fuel filters , I turned around and crawled back home and changed fuel filters still no power. no codes "don't no where to start".
View 8 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didn't have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines, harness, pump, sending unit , tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to the garage had them swap it out and now they said come get the truck they won't work on it anymore that now it needs 3 injectors and they won't touch it with aftermarket fuel system on it. So i go to drive it home and it starts but runs rough and u can hold it to the floor and it won't budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now.
View 10 Replies
