Ford 6.0L Power Stroke Diesel :: 2006 - 4WD Quit Working
Nov 3, 2015
My truck does mostly pavement duty so no telling how long ago 4WD quit working but I needed it the other day and it's now a no-go. It's the '06 truck in my sig and it has ESOF.
When I flip the switch (4hi or 4low acts the same) my A/C continues to come out of the dash vents, it doesn't change. With KOEO I can hear a whirr-click from under the truck when switching 4wd on and off, I get noise both ways. 4x4 light on the dash seem to work correctly.
Broke out FORScan and got the following info:
===GEM DTC P1832===
Code: P1832 - Transmission Transfer Case 4WD Solenoid circuit failure
Module: Generic Electronic Module
Diagnostic Trouble Code details
Transmission Transfer Case 4WD Solenoid circuit failure
===END GEM DTC P1832===
[Code] ....
Any tips to quickly nail it down between the switch, GEM, wiring or solenoid? Looks like the whole thing is failing. I've climbed under the truck and all the wiring appears undisturbed. No recent work under there. In FORScan, these DTC's were generated in a user initiated test and I didn't pick up the instruction to re-run the test in 4x2 mode until I posted just now.
Under the hood everything seems to be routed correctly and connected. Vacuum pump runs a short while on start up like always has. I can lock hubs manually and they don't seem to be binding hard but they are a little stiff, haven't done that before so I don't know how hard it should be to turn them. I have a MiteVac but haven't tried using it to try and lock the hubs. Not sure any of that matters (yet) with the DTC's listed above.
View 14 Replies
Advertisement
My work truck that I drive, a 2006 F-150 Lariat 4x4 extended cab, rear parking sensors quit working. The button on the dash is lit up all the time like when you shut it off. I posted this on the F-150 section too and was able to find a suggestion that you can listen to each sensor while in reverse and if you don't hear a clicking at the sensor it has failed. All (4) sensors are clicking away while in reverse so not sure what else to check, no one in the F150 section, so that is why I put it here.
View 3 Replies
I went on a 4oo mile trip the other day and kiddos were in the back playing games and powered up- Next thing I know the AC seems to not be working. It was pretty cool outside so I tested it a little and I could not feel any cool air in the seats and teh vents were not very cold.
Clutch seems to be engaged and not cycling.
I am taking back to them Wednesday.
View 4 Replies
The only problem it's had is the heated seats quit working.
View 14 Replies
So just recently my remote start quit working. It's worked fine for the last two years. Now after I hit the buttons the truck just honks. I tried going through the setup on the dash and turning it off and back on. Still just honks at me.
View 8 Replies
So for 4500 miles since new my truck has been displaying, on the right side of the instrument display in the center dash, the actual gear the truck is in. I would shift from park to drive and move out and the truck would display what gear it was in by placing a lighted box around the gear number as it shifted 1-6. Now that display is gone. It's not anywhere. If I go to the manual mode it will display that, but the normal numbers from 1-6 , bottom to top , are gone.
View 14 Replies
My SYNC voice commands witch I refer to as " Shiela" has quit working. No voice and it does not recognize phone. Just displays " no phone" ????
View 12 Replies
We just replaced an injector in my truck. Everything was fine, ran great, etc.
On the freeway home, the dash, windows, locks, radio all quit working. at first they'd stop and come back, stop and come back, etc. then finally they stopped. As I was getting off the nearest exit, the truck started dying on me. Once I got pulled over out of the way, it acted like the battery was completely dead.
After a few minutes of scratching my head and staring under the hood, I happened to look at the passenger side batter, and the crossover cable from the drivers side was broken off right at the terminal!! We must have broke it off while doing the injector. as I look closer at it, it had been broken before. Some idiot before me had actually taken a broken crimp style terminal, shoved it and crimped it into a new one and called it good.
I was able to redneck it back together so i could finish the last couple miles home. I fixed it properly with a new crimp terminal, heat shrink, etc. Why did the engine die with the crossover connection broken? was it because the series was not complete, and all the electronics were running off the battery(s) and not the alternator? I'm really confused. I've heard of people only running one battery before.
View 9 Replies
So i had been up in the woods for better half of the day. I had been in 4wd a few times, didn't thrash on anything and while driving home about 30mins into the return trip on the pavement i noticed my speedo only showing 10mph. I know i was easily going 50mph. I changed my SGII gauge to show MPH and sure enough i was going way faster. Eventually the needled dropped to zero and stayed that way for at least 5 miles. Then I came to a stop to and made a right turn giving it a bit of throttle and the speedo began to work correctly and did so for the remaining 5 miles. the Odom also during that time wasn't adding mileage. could this be from the rear sensor ontop of the rear diff?
View 6 Replies
I have a 2005 F250 with 6.0 Crew cab
Wanted to change out factory bulbs to LED's. The factories were working just fine, just wanted LED's. Broke a couple of center bulb holder's/clamp. Don't really know what they are called. Went to junk yard got a couple of used ones, those worked because when we opened the doors on wrecked trucks Dome lights came on! Got home put them in and NOTHING. No dome, no map lights with LED's. Changed back to factory bulbs and only map lights come on, NO dome lights on front or back and my 3rd brake light quit along with the 2 bed lights. Checked the wiring plug and have power to one wire. What fuses would I need to check or to check where next? Owner's manual is not very specific about which fuse.
View 1 Replies
My Edge is reading "PO528: Fan Speed Sensor Circ No Signal". When I'm pulling a large 5th wheel up a 4% hill by the time I hit the top (if I don't slow down)warning beeps are gong off and my ECT is at 240. I can hear the fan come in at 215 and it stays in all the way up in temperature.
All the posts say c/o the fan clutch. While that may fix the fault signal, would it do anything for the temp situation. If the fan is locked in it seems like a lot of money just to clear the fault. Or......is the fan still slipping but sounding like it's working? This my be not related but I did notice that as the temp rises the AC starts not working. By the time I reach the top of the hill it is blowing hot. As we go down the other side and ECT comes down, it starts cooling.
View 9 Replies
I have an 06 f250 6.0. When I bought it a few weeks ago I turn the key on and let the glow plugs warm up and start the truck it would start easily. Now it seems like it's taking longer to start . The temperature are between 50 and 80 degrees. I changed the fuel filters and it's still taking to long to start.
2nd I noticed today that when my truck is at idle the Tachometer is at 0 and when I'm driving 60-70 MPh it goes up to 900 or maybe 1200. It seems to be running fine no loss of power that I can tell. What could be causing the long crank time and my Tachometer problems.
the glow plugs and injectors are new I don't remember the brand and the fuel filters are brand new Motorcraft.
View 1 Replies
I am working on my dads 06 F350. He had four dash lights go out, so we changed out the bulbs and put the dash back together. When we hooked the batteries back up all the gauges reset except the the boost gauge. The needle went way past 0 and bounced for about 2 seconds then it just stayed below 0. We have tried to reset it by unhooking the batteries and turning the ign. switch on and off several times. Always go back past 0 and stays there. It does work it just doesn't read correctly. I am pretty sure that the needle did not get turned on the shaft? Is there a way to reset it?
View 3 Replies
On my 2003 powersteering the windows and radio will just quit working. Then they will come on again. Maybe in and hour or a day or a week. Where do I sart.
View 6 Replies
I have an 04 f350 and the other day the windows and radio quit all at once. Lots of people are having intermittent problems but mine went from being fine to nothing all at once. I tried the circuit breaker and the relay but nothing seems to fix it. What this is?
View 8 Replies
Recently turned 100k and since have had my exhaust RTD's go out. While fixing that they found the back radiator leaking. Since then both batteries died which didn't surprise me at 40 months. Then my windshield washer started leaking, then my DEF heater went out and two days ago my AC quit. I was ready to buy a new 2015 but now not sure. I've contacted Ford customer service and they are getting with the dealer to see what they may cover but haven't heard anything back yet.
Mine is a 2011 with 105,000 on it. This is pretty frustrating. I have been very pleased with this truck up until now it has been very dependable. However when that dependability begins to go south at only 100k it brings to question what exactly are we paying for here? A heavy duty truck that costs upward of 60k should be one you can count on for a lot longer than that. How Ford approaches this with me is definitely going to have a direct bearing on which 2015 diesel truck is in my driveway in the next few months. Again let me say that i have been very pleased with this truck and FOMOCO in general.
View 11 Replies
I'm working on a 2005 F350 with a 6.0. The customer was driving the truck when it suddenly quit running and now it won't start. The only code stored in the memory is P2290 - ICP too low. With my scanner connected the IPR is showing 85% duty cycle and the ICP is only showing 5 psi while cranking. I disconnected the ICP sensor while cranking but still no fire, so I removed it and connected a pressure gauge which shows zero psi while cranking. I hooked up a cylinder leakdown gauge to the ICP port and with 100 PSI of air pressure I'm showing less than 2% leakage with the IPR energized at 60% duty. Thinking the hpop was bad I replaced it but still no change. I also tried a new IPR but no luck there either. I removed the oil filter cartridge and verified the low pressure pump is pumping oil while cranking. Could the inlet screen be plugged inside the oil cooler? I'm at a complete loss.
View 7 Replies
This morning, I started my truck to go somewhere and less than a minute into my drive, the engine suddenly died. I tried cranking it again to which it started but less than a second later it quit again. That's when I noticed my FMP on my SGII was at 0v. When I got it back into a parking spot, I pulled the FICM and tested the connectors as well as the relays and they all were normal.
I decided I will be pulling the FICM again tomorrow and I will be sending it back to FICM repair.com for them to look at as I got a new one from them about 8 months ago. However if it is in case the wiring harness, where is a good place to look. I don't think it is the wiring harness as it seems to have voltage at the connectors.
Also this may be related but earlier this week, my Scangauge froze and I unplugged it and plugged it back in and it didn't connect to the PCM until I reset the SGII to factory settings. I wonder if this is related?
View 14 Replies
Well today the tach was not working at all and the check gauge, check engine and glow plug lights are staying on. Truck runs and starts great, everything else seems to work except the trans temp gauge. Did a search for the GEM and could not find anything that indicates the GEM controls the tach and warning lights.
View 14 Replies
Luckily I was sitting in the driveway. Pulled the truck out of the garage. It started fine, idled fine, did not make as much noise as I was expecting but was warmer in the garage than outside. Stopped in front of the garage door to grab a couple things in the garage, jumped back in and it quit before I could get it in gear and roll out. Weird. This is the first time I've ever had to get a tow.
View 14 Replies
I recently had my fuel gauge stuck on full and at around the same time, my left rear brake light doesn't work. I do have LED brake lights in the rear so I am not sure if that changes anything. I thinking something with a ground or is it possible that these aren't even related.
View 2 Replies
