Ford 6.0L Power Stroke Diesel :: 2006 - Replaced 110 Amp Alternator - Can Handle Enough Power?
Mar 28, 2016
OK...I ask that you bear with me while I explain my question/issue.
I bought a used 2006 F350 Super Duty diesel last October (Oct 2015) and it has about 124,500 miles on it now. Last week, the power cut out as I was driving home from running an errand. Jumped it and got it back to the house. Suspected the alternator as both batteries tested low (according to AutoZone). Purchased the 110amp alternator and after a few days...I was able to get the alternator installed. AutoZone charged the batteries back up.
Today, I was able to start the truck and drive it around the block in order to make sure everyone was okay - before I took it out on the streets. Got back to the driveway....ABS light comes on, radio shuts off, odometer light goes off, etc. I shut the engine off and let it sit for a minute. Try to start it back up...and nothing happens. Ended up disconnecting both batteries while I ponder the root cause of the issue.
Is it possible the 110amp alternator is not strong enough to handle the power requirements (and that's why the dashboard lights went out)? To the best of my knowledge, there's only 1 alternator. The only "extra" that's installed is the tow/haul package (which I haven't used yet). According to the Ford Parts web site - after I enter the VIN for my truck - the results show a 110amp alternator (heavy duty alternator).
Would exchanging the 110amp for the 140amp be the most logical place to start? Or is there something I missed as a replaced the alternator?
View 14 Replies
Advertisement
My 2006 F250 has a single alternator and recently the charge light is on intermittently and I have watched output voltage fluctuate between 12.4 to 13.5 ... sometime a .3 volt bounce one way or another for no noticeable reason.
So rather than buy a new alternator, I would like to replace the voltage regulator and put in some new brushes.
What are part numbers that I need to pick up?
View 6 Replies
After 2yrs and 1mo, my DC power 270XP amp died. I put the almost 10 yr old factory alt back on and everything is good again, except for the glaring fact that I have a dead alternator. It is a month beyond warranty (of course).
Truck has been running great. Oil cooler, EGR bulletproof cooler, STC done in Dec at Ford due to high deltas. I have a small stereo - one 12" sub woofer, otherwise nothing that really stresses the electrical system. I did the "big three" with 1/0 copper - cost a fortune, saw no difference - but that could have been an issue for the alt.
I left a message today with etch support but did not get a call back. I hope they make good on this - I waited almost 4 mo's to get this thing and it was supposed to outlast my truck.
View 14 Replies
2006 6.0 king ranch 189k sct live wire Replaced 1357 injectors and when I crank truck it will crank and sputter for a brief second but will not fully start and continue cranking and doing this over and over. Tried starting for roughly 30 minutes would not budge. Tested icp and ficm both are good. Also replaced batteries, fuel filters, checked all relays and fuses still can't figure it out. Also truck is bulletproofed.
View 6 Replies
i just had my 190amp DC Power Alternator just died. It was about 4 yrs old. I ordered a new Bosh AL7606 I know it's 140amp but it was half the price and in stock on amazon also lifetime warranty. I'm thinking of moving the pulley from the DC Power to the Bosh. Any thoughts? I went to the DCPower website but they were sold out and twice the price. I might just get the DC Revuilt as a spare?
View 14 Replies
I just wanted to share with you all a cautionary tale about belt tensioners and idler pulleys. I am now a firm believer in installing the aforementioned items when you replace your drive belt. 15000 miles ago I replaced the drive belt and didn't heed the warning of some here on the forum.
For the last month or two I have noticed what sounded like road noise which I dismissed because I had just had new tires installed that had a more aggressive tread pattern than my previous tires, I also noted that the ECT had been a bit higher than normal, like running in the high 190's to low 200's on average.
Well while driving today I get the alternator warning light and lose power steering and soon after the brakes got stiff, this was followed by ever increasing ECT which got to 242* before I could get it off the road and shut down. It is too early to tell if the noises and the ECT temp rise were the result of this tensioner going out...
For what its worth the only tools required were a 10MM end wrench and a bit of skin to get the job done.
View 5 Replies
What it is or why there is a three inch pull handle hanging down on the bottom of the Diesel Tank on my niece new 2012 F350??? It is sitting hanging there begging to be snagged and ripped off the bottom of the tank!!!!! I'm at least going to Gorilla Tape it up to the bottom of the Tank.
View 10 Replies
I was driving and my truck started have lack of power, could barely get going on hills, tons of blue smoke (smelled like diesel) real rough idle. I unplugged injectors and found #5 made no difference. I replaced it today and I can't get it to start. It'll get to 2000+ psi 48v ficm, low pressure oil registers, ficm says its in sync. It will crank and blow a lot of black like its half firing or something. It has even crank to, until it tries to fire. From what I've been reading could it be the ficm? That one circuit is fried?
View 14 Replies
Backed up into a bush and it seems it was a little bit more stout than expected. There was a large branch that pushed my tailgate latch so far up now it's stuck. If you look at the pics below, there's a tab on the right hand side that was over extended and now stuck/holding the handle up. I'm a little reluctant to just try hitting it as hard as i can out of fear that I'll snap something.
View 5 Replies
I have a 2003 F350 6.0. I had a flickering Battery lt on the dash last week so I replaced the Alternator. People recommended I upgrade to the 2005 140 amp alt from my stock 110. I have a single alt system. So I did, today it died on way to work. Batteries were drained. Had new alt checked and its fine. So All I have is a wiring diagram from 99-2002 but it shows the plug on the alt with 2 wires, Lt grn/red from switched ign and Org/Lt Blu which goes to batteries. Org/Lt blu has 12v but Lt green/Red has nothing with ign sw on. I did check fuse 45 in Central J box and have power there. I did notice I have no battery Lt on dash when you turn Ign sw on, and never got the Lt this morning when it died. What Im confused about is do I have a PCM? my diagrams that only go up to 2002 model show it for a 2 alt sys but not for a single alt. I should have power on Lt Grn/red with ign sw on correct? Everyone said 2005 alt was plug and play, the elec connector is now pointed down, where it was pointed up on the orig alt, look to be wired the same.
View 7 Replies
What this part it is? It sits over the alternator on the driver side and looks like a couple vacuum hoses plug into it. Mine is making a very loud buzzing noise.
View 8 Replies
I have a 06 F250 6.0 My battery light has been coming on. Doesn't stay on but I'm planning a trip back east and don't want any issues to occur. I was thinking maybe the batteries. So I stopped at the local Oreilly's Auto store and had them tested. Told the guy what it was doing and he said it sounded like the alternator. He tested it and said it was going bad. He also tested the batteries and said they were good. So I went looking for a replacement alternator and they have different amp sizes. So I'm not sure on what size the original one is and if the replacement should be a bigger size amp wise.
View 11 Replies
2005 F-350 6L
Just changed my alternator, that was the easy part apparently...............
Cant get fan belt back on? My pulleys don't look the same as the picture under the hood. I can see a idler on passengers side down low, but cant seem to make it move to give me some slack.
What kind of tool to use on idler to get slack?
View 14 Replies
I ve been noticing that the alternator isn't charging correctly, or at least it seems like it. We drive short trips sometimes two times a day, a mile or less. One day, night actually, I noticed it started to not turn over with it's usual enthusiastic sound. When the batteries get discharged to a certain point, the voltage at idle will be less than 12 volts. If I rev the engine for a bit, the volts jump up, but at idle it drops back to 12 or below. Seems to me that it should be at least 12v or above if the batteries are discharged, and more towards 12.5ishV if the batteries are fully charged.
After I put it on a 6A charger overnight, the voltage upon starting is above 12, sometimes over 13. But if the batteries start to dwindle down from short trips, the voltage drops to 12 or below at idle.
I did install the smaller pulley a few years back, and that worked massively. I couldn't get 12V at idle before installing the smaller pulley. But now it seems like I'm back to that same situation before installing the smaller pulley.
So, I m guessing that a alternator bench test is in my future? The batteries are fairly new, tho they have been down to nothing at least twice from boneheaded moves by yours truely!
And, I'm speculating that this charging situation contributed to the recent FICM replacement that I went thru.
View 14 Replies
I am having a charging system issue. The alternator is making barley over 12 volts. With KOEO the battery light on the instrument cluster does not come on. I have already replaced both batteries and the alternator -before i noticed the battery light is not coming on.
View 2 Replies
We've got a 2012 F550 6.7 with 138k. It recently got a battery light. The batteries are right around 12 volts with the truck running or off. I also tested the output on the alternator and its not charging. I put a new alternator in it and still no charge. All the connections are tight and clean. The batteries load test ok. Where to look next?
View 4 Replies
So I have been having this little issue for a few weeks now. I will be driving along and out of nowhere my batt light will come on and my gauge cluster,radio and windows stop working and the ficim volts jump to 15.5-16.5. This is an intermittent issue. Yesterday I put my multi meter on the alternator and I am reading 13.5 or so this number was done at idle and the batt light was NOT on .
View 14 Replies
[URL]....
My truck has never felt like it has run right since I replaced the leaky ICP. The replacement was not a Ford or International product so I am afraid that it was a mistake. I replaced the plug also. I'm sure I got the wiring correct. I've been several hundred miles since.
I got on it today to get on the interstate and threw a code 2286. I cleared it and drove for a while to see if it would come back. It does fine unless I get on it, then it will throw the code again. I did it twice in a row so I figure I have bought a cheap ICP? My scan gauge is not good enough to get all the on the on the fly info you need.
View 9 Replies
I have a 2007 f350 6.0, just replaced the oil pressure sensor in January, now, my truck is surging like crazy! I heard it could be the ICP sensor, how easy is this to change? And where do I find it if this is the problem!
View 1 Replies
Had a bad turbo on my 07 F550 with a 6.0. Replaced it today and took her for a ride. Started smoking and oil was spitting out of the weep hole in the muffler. A lot of smoke. The truck was smoking before I replaced the turbo too but I didn't have any oil coming out of the weep hole. I'm hoping it is just oil that had been passed into the exhaust by the bad turbo that is now being burnt off and pushed out by the new turbo. Does this sound plausible?
View 1 Replies
In the last 2 months I've replaced my starter and 2 new batteries. I've tested the alternator and it's fine. What more is there? I'm guessing the FICM is going to crap. If I attach a scangauge 2 to it now would it tell me if that's the problem?
View 14 Replies
