I have a 2006 that shuts off in a hard pull, if I wait 3 minutes it starts again. I hooked up my scan tool and when it dies and I crank it it only builds 200psi oil pressure, let it sit it builds enough pressure to run fine. If I dont push it over 3500psi for more than minute it wont die pull a hill it dies again. Is it the hpop or an o-ring.
View 10 RepliesI have a 2011 F250 6.7 4x4 CCLB. About 90k on the odometer.
Full flopro exhaust(no cat, no dpf) and a H&S tow tune. Otherwise stock.
8" lift and 37" toyo mt tires.
Anyways, I ran the truck in my first truck pull ever a few weeks ago. I pulled in 4wd high, rear locked, tow/haul mode, traction control off 2nd gear.
I wasn't able to pay super close attention to all of the stock gauges, but it didn't over heat and it didn't rev over 3000rpm. It was pulling like a freight train until the 125' mark and it just shut off. I thought something may have broken.... I put it in neutral, cycled the key and it started right back up....
Checked for anything obviously wrong, no fluids, all boots looked attached and fine. Nothing. Drive it home and haven't had a problem since. No CEL, no warning no anything. So why the truck may have stalled on me?
04 with 170k miles. truck runs fine. every now and then truck shuts off while driving. turn it off the it restarts every time. Only code that comes up is number 6 injector. The contribution test injector is firing right. FICM voltage is 47.5. has new ipr and hpop also 6k miles ago. Could it be number 6 shorts out or something crazy killing truck? or maybe a crank sensor.
View 14 RepliesYesterday, my truck began to shut off abruptly. Under every condition, from idling to slow running (30mph), and 70 mph, to load and no load. Wait 1 minute and it would start and run for 1 minute 15 seconds. If the batteries were disconnected, the truck would run for 13 minutes before shutting off. Have replaced the fuel filters. Still does it, but runs for between 10 and 20 minutes before shutting off.
Am seeing only two errors codes. P1000, and P0603. I was 40 miles into the Ville Vidal, when this started, and 150 miles from home. To get home, I disconnected the batteries too many times to count, and bled the HFCM numerous times. Am also seeing the moisture in fuel icon on teh dash light up when it quits, but so far as I can tell there is no moisture in the separate.
2003 F450 6.0, automatic. 150K miles.
2004 f350 after i shut the truck off something was buzzing. So I popped the hood and found its the injector harness or injectors.Is this normal or something I need to look into?
View 3 RepliesI have a 2005 f250 just hit 180k last week and it has the 6.0 in it, egr deleted, sinister diesel oil cooler, stc livewire tuner with street tune installed, air raid air intake. Wicked wheel 2 in the turbo. Its throwing codes P0606 and P0341. Cam sensor has been replaced and the other code is a mystery to me. Its been randomly shutting off like you turned off the ignition all day today.
When it stalls it takes 3-4 times to get it fire back up. When you first go to start it the pressure gauge reads 0 but once it fires up it says theres pressure. Also some of the days it never stalls and runs like a champ but other days i cant drive more the 10 feet and then it stalls. I have no idea whats going on with this truck and ive put lots of money into it doing customization and stuff like that so I am hoping that its not on its last leg....
If I am going over 40 mph and I have to brake hard my truck pulls really hard to the right. I mean so hard it will take me off the road. My truck is a 2004 f250 with 147,000 miles.
In the last six months I have replaced both hubs, rotors and brakes. I really drive like an old man so I don't know how long I have had this issue. Just someone pulled in front of me on the freeway and I had to brake hard and I found this out.
I have checked both front capilers and brake lines and those are fine. I have brand new tires on it. I really have no clue what is going on. I have pulled the brakes off three times and checked everything out and it looks good. If slowly push the brakes everything is great, it is only when I have to really slam on them.
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 RepliesOn Saturday I drove my truck 450 miles, all of it towing, in hilly New England. The turbo boost gauge was operating at 20psi or higher for many of the hills, and the 13mpg average was indicative of how hard the truck was working (normally empty I will get 20+). The next day, I drove it about 3 miles and it started a regen. Why? Wouldn't it have been passively regenerating for most of those miles? A steady 75mph for hours at a time?
View 14 RepliesEarlier this week the truck was hard starting every time. Tested the batteries: 12v engine off, 14v engine running, all good.
The next day it threw a P0284 – Cylinder #8 contribution/balance, and was clearly missing on a cylinder. Despite the lack of a puff of smoke at start-up, I was pretty sure it was an injector. So I ordered one from White Bear Lake, and a fuel pressure test adapter from Strictly Diesel. Then I decided to do some testing with AutoEnginuity. Tried the injector buzz test first and got a note that the truck was not capable of performing the test. Tried starting truck and gauges swept and wouldn’t turn over. Tested batteries again: main battery 11volts, aux 12volts.
I got the batteries in and the stupid thing runs like new. Only codes are P1000 and P0603. Truck passed the injector buzz test, and cylinder contribution test graph is almost a flat line.
Take-aways:
1. Bad batteries can cause all sorts of havoc.
2. Always use a voltmeter that displays tenths of a volt, because if it’s only showing whole volts, it could be rounding up. The 12 volts from my first test was probably more like 11.6 volts.
3. Always do as much testing as possible before buying parts.
4. Costco does not sell Kirkland batteries anymore. They only stock Interstate, and the Interstate warranty has dropped from 36 months free replacement to 30 months.
5. The Walmart and Autozone batteries with the five year free replacement are “out of stock” and I’m guessing they won’t be back with Interstate dropping their replacement dates.
6. Most of the car batteries in the US are made by Johnson Controls.
7. Motorcraft batteries did not get very good reviews.
8. Interstate said that AGM (absorbed glass mat) batteries stand-up better to the additional vibration and heat experienced under the hood of a diesel, but they are significantly more expensive, and not all the brands offer an AGM with a better warranty than their best lead-acid offering. Also, the guy at Sears said AGMs are only beneficial for newer cars that continue performing electronic functions after the ignition is turned off. He said he’s seen lead-acid batteries outlast AGMs, but didn’t specify if those were out of diesels or not.
Questions:
1. Can I expect the P0603 to go away after the drive cycle is complete?
2. What should I do with the new injector? If I return it there’s probably a restocking fee. If I wait for a complete injector failure I don’t get the core charge back until then. With the FICM compensation, I don’t know of any way to identify weak injectors without IDS.
Have 65k now..OEM breaks. Never an issue.. going along today had to make a fast turn left into a parking area. Hit the brakes doing about 50 made the turn. Slowly found and kept rolling to a parking spot. Went to apply the brakes and found the pedal was rock hard. The truck kept rolling slowly. Pure luck I was were I was.. I tried to shut the truck down and restart. Still rock hard pedal in up position. No breaks.. not enough to stop at idle. Checked the brake fluid and it was fine. Went inside the store to grab the delivery and when I came back out I tried to work the pedal down.. I felt some give.. put it in reverse to check it out..(couldn't go ahead no room.) slowly the breaks came back. Has been fine since.. driving all over town today. No codes or engine lights.
View 14 RepliesWhat it is or why there is a three inch pull handle hanging down on the bottom of the Diesel Tank on my niece new 2012 F350??? It is sitting hanging there begging to be snagged and ripped off the bottom of the tank!!!!! I'm at least going to Gorilla Tape it up to the bottom of the Tank.
View 10 RepliesSo I went to start my 2006 this morning and it would not crank at all. Like the battery was dead ( all the light in the cab and headlights were working fine. ) so I tried to jump it and still nothing no clicks not crank no nothing. Just for fun I went ahead and jumped the starter (using the same method as when I prime the hpo system) starter cranked no problem so I put the key in the on position and cranked the key again still nothing. So I put the key in the on position again and jumped the starter truck fired right up. So I went back in the cab and tried to start it with the key and it started right up like nothing ever was wrong. What was causing this? Also my voltage was at 11.5 with the key on and engine off when it was running the volts were at 12 to 12.5
View 5 RepliesSo today on my way home from work. I got off at my exit and when I went to step on the gas I lost power and the truck wouldn't exceed 15 mph. It would just rev up and down. It was pouring white smoke from the tailpipe. At one point it went back to normal and started running fine for about 10 seconds. Then it went back to doing the same thing losing power and spitting smoke. I limped the truck into a parking lot and called a ride. I'm having a tow truck pick it up on Monday and take it to the dealership. Is this a head gasket issue? And I feel like it's going to be expensive. 2006 F250 6.0L .....
View 11 RepliesJust replaced injector 4, oil cooler and did egr delete. Ficm is at 48 and truck will not kick over. New batteries installed.
View 14 RepliesSo my 06 6.0 4x4 is just about to break 200,000km and I've done most of the upgrades and work myself. (All the updates are in my Sig). My problem is that when I'm cruising and the engine is at full operating temp, if Im bellow 80-100km/h nothing but as soon as I break into that speed range about 2000rpm the truck will start to shudder. Almost feels like its not firing properly is the best way to describe it. Why this could be happening or causing it?
View 7 RepliesI have a 2006 f250 with a 6.0 and I am having some issues with a hesitation and lose of power. The hesitation is worse when under load and other times is not so bad. Also it is non existent at higher RPMs (2500 and up). I changed the egr valve 2 months ago and it seemed to fix the issue (95%) but now it is running bad again. I used Hot Shot oil additive 2,500 miles ago and I changed the fuel filters and changed to 5w 40 Rotella synthetic oil, nothing has changed. I had the FICM changed a year ago with new software updates, still didn't fix it 100%.
Now I am having a "hard" start issue. It takes a bit for the truck to turn over. My batteries are 12 months old and I just replaced the alternator so I am not sure how to proceed.
I did just buy a Scangauge II and I am still figuring out how to use it. It says there is no codes.
Friends truck, 06 with 135k. Problem he's having is, truck cranks over fine but doesn't fire, if he kick starts it, it fires right up. Haven't had the chance to put my AE on it, figured I throw it out there.
View 7 RepliesMy truck died a few weeks ago on the highway had the hpop ipr valve and screen replace ran awesome for 2 weeks, shut it off ran into the store and it wouldn't start gave it a couple hours finally fired, started good the next 5 times go to start it the other day no start again, tried again 30 seconds later and starts trucks a 2006 with 226000km throwing no codes, I'm ready to go trade it off on a new one, where to start?
View 9 RepliesI have a 2006 F250 6.0L. Just had a used motor with 108k miles put in. Had the motor studded, fire ringed, new injectors, new glow plugs, new radiator fluid filter system installed, had egr delete done, ficm board replaced, fuel pump replaced, a few other small items replaced as well. The problem I'm having is the truck runs like it has a miss until it warms up.
After that, it runs fine. It takes about 10/15 miles of driving before it runs like it should. Letting it run in the driveway for 10/15 minutes to warm up doesn't make a difference. When the truck starts, it lopes at an idle for about 5 mins before turbo kicks in & starts whistling. When I start driving it shakes & feels like it has no power until it warms up. Then you'd never know anything was wrong. Put way too much $ into the truck so far and can't keep going.
I have a 2006 F350 6.0L. That is Having trouble starting after it is warmed up. Ive been told multiple things it could be but the one ive been told the most is the Stand pipe or dummy plug in the oil rail having a small leak. Is this correct? Or is there something else i need to Check??
View 8 Replies