Late build 03 f350 auto, I got a p0500 code and noticed sometimes after 2rd-3rd gear engages theres a shudder or fast vibration for few secs unless i let off, it didn't start this till i took batteries out, where is the location of the vss at, I am seeing some say at each wheel, on top rear diff, on top back of trans so not real sure?
View 7 Replies05 F-350 6L .. Automatic Transmission
When I got the truck I noticed it would slam hard into reverse. Ever since it is taking longer to engage reverse gear and now I have to rev it to 1000 rpms for it to engage with a hard SLAM.
I also noticed that if I do a fast take off, there is a knocking sound coming from drive shaft/differential area (like knock knock knock knock knock then goes away). Then a slight vibration ending at around 30 kph (~20 MPH). There is also some oil leaking from the transmission. I added some mercon sp yesterday - it was a bit low.
My guess for the knocking and vibration is the center support bearings and U-joints. Transmission??? One thing I know I am going to be banging away at that shaft but the transmission problem really scares me.
I have already logged 6K miles on her, crazy, but it's my job. I have pulled 5 maybe 6 trailers (form trailers, about 15K pounds loaded, this time of year). Loaded or unloaded, when I push the throttle in 2nd, 3rd gear, I feel a shudder, like transmission shudder.I know this thing throws down 800 ft. lbs. of torque, should I not be pushing it so hard? Or, what am I feeling?
View 14 RepliesI have a 06 6.0 no start . I was at a light felt a slight shudder went to take off felt another shudder and it just died. Changed fuel filters, unplugged icp no start still. No code at first now throwing p2291. Fuel pressure is at 62 when cranking. Hooked up air to the icp port and only heard air coming out of both valve covers inlets. Ipr was at I believe 60 to 65% when cranking. Little back round 2 years ago I did the whole sinister diesel top end kit and put the updated parts in. New o rings on everything that took them, new egr valve, standpipes and dummy plugs. On the injectors all new o rings and crush washers. I believe that's everything.
View 11 RepliesSitting at a light. I noticed a slight vibration while in gear. Get home. Put her in park and noticed it again. Took her for a spin again. It seems to do it at low speeds, cruising and goes away once I'm on it? What would be a good starting point to track this down?
View 2 Replies2004 Excursion... 1st time into a 6.0 for me so I took my time. Truck has 192000miles.
PHP Ficm atlas 40, 58V Swamps
SCT Tuned via X4 (recently)(Extreme street at the time)
Synthetic 0w30 summer and 0w40 winter.
FORD filters ALWAYS, 5000mile intervals no pushing it
FORD fuel filters, BOTH regularly.
Studded, AFE Stage 2, Liberty EGR Delete.
42's, 4:88's with Detroit in rear
Highway driving and feel a stumble. Weird, then another, ok that wasn't a bump. Then steady rough idle and a heavy vibration when I lightly got back up to speed to get myself home.
Had new filters so started there. Just changed in the spring here and they were in pretty new condition but swapped them out anyway. Stripping the cap, 120 bucks and had to put a new one on.
Start truck and still rough idle, test drive and still a bad vibration.
SO, I read and search. Scanning with Ford or AE are my number one priorities and they were done along with Fuel pressure check.
Scan revieled Inj 6 out, fuel pressure at 60 PSI. We pulled plugs off injectors with results except 6, confirming it's not working.
Ordered an injector and the Aliant Power rebuild kits to freshen up the other 7.
Disassembled all 7, NO stiction problems at all and all 7 spool valves were clean as a whistle. Bodies of injectors were good on 6 of them and had a screen in cyl 3 what was completely gone (the 3 screens around the body of the injector). Tip was also plugged but one hole. (used brake cleaner in tip and air to confirm 6 holes were clear) Used the body of the core on that injector but not the spool part. Replaced all O-Rings incl the seal inside the top where rail snaps into. Sanded spools (800grit 2-3 turns) and installed same way they came out. Stem pipes and dummies new as well.
Reassemble, carefully and fire truck. WOW....running abit rough but smoother. Ive read it takes abit to get air out of system and to expect longer cranks ect. Shut it down. INspect for leaks. Button up the ficm, and few other things. Re-fire truck with abit longer of a crank. Fires and running smooth. HERE's where it starts acting up again. I can feel a small stumble....then another....then full time again. Exact same as before. Pull 6 off and it's that injector again.
Here's the big mistake I made. Reinstalling injectors, I put the new one in #4 spot and number 4 in 6's spot. Not smart, I know.
Pulling inj plugs off around entire motor while running and def No 6.
Put things away, call buddy and he says possible FICM. or harness.
So i pull inj harness and OHM every single pin and map it. 100%, I go grab his "good" ficm and test with that. HOLY COW, FOUND IT. Started great... Then as she warmed up ICP at650ish, EOT ECT getting to 100-110F (only a 4-5* delta always monitor) is starts to vibrate and run rough again.
Read some more....OHM testing is one thing, actually load testing harness confirms if it's actually no good. Harness is 450 bucks plus our lovely 13% tax so I want to diligently cross this bridge. Grab a harness off a running 6.0 and test next day.
Fires up and runs smooth. Then, as temps come up it starts again. Walked away last night and when I fired up this morning. Started great and as she warmed up vibration was back. Along with a intermittent squeak from the turbo housing area.
Codes.... SCT X4 tuner is reading nothing DTC's and hasn't since day one so I "assumed" no codes until buddy scanned with AE and since it's last WiFi update wouldn't connect to computer and gives me error code 10007 when I try to tune. **Ended up fixing last night, went into another "Tune revision update" and now connects to my computer AND returned my truck to STOCK and resested truck. Still running rough.
So I plug my PHP FICM tuner and get codes:
P1102 "Unkknown" (reading here I had my AFE off and not plugged in)
P0113 Intake air HI input
P0284 Cyl 8 cont/bal Fault
P0603 Internal control Module KAM error
P0611 FICM Perf (58v swamps, I've read always throws this code and I've had that code since day 1)
P0676 Glow #6 fail
Lastly I'll add, no smoke out tail pipe at all during all testing minus the black puff when tune loaded.
Trying to track down a vibration issue. Not steering. But, idling in gear and driving. I feel the vibration through the go pedal and floor board and seat on driver side.
Checked obvious points. Down pipe, complete exhaust system. Motor mounts, tranny mounts and steering.
Got to be some other spot I'm missing. Checked driveshafts. Everything seems OK.
I recently bought this Ford F250 6 with 117k... I've had it 3 weeks and it is now at 120k... My Odometer is reading Fast. From Tucson to Phoenix it read 302 mi, on my trip monitor it read 102 mi.. I've made this trip many times before and 102 miles is about right. It's a big issue because I get paid by the mile.
View 13 RepliesMy truck was parked at home and hadn't been started for 10 days. When I did start it for the first time, I heard the cooling fan spooling up or down, consistent with the engine rpm. After pulling away from my home I saw the fan speed spool up to near 2,800 rpm during the short period it was locked-in with the engine speed.
While driving out of my neighborhood, and about 1/3 of a mile from my house, the fan returned to normal speed of about 480 rpm. I have the FSS pid displayed on my Scangauge and was able to see the fan speed while hearing it. Now I know what the fan sounds like at a high rpm. It makes quite a roar.
This has never happened before. I've driven the truck a few times since then and it hasn't occurred again. What may have caused this?
When cold starting the transmission shifts into reverse perfectly, then after backing up the car and shifting into drive it hesitates for 4 or 5 seconds before it engages the forward gear.
2008 Accent 4 door automatic 77,000 KM
Have a 2003 F350 srw 4x4, 107,000 miles on it. Driving it last night tow/haul light started flashing, hooked up AE got a P0730 Incorrect gear ratio. Truck seem to do ok, cut it off went back out a little while later and the tow/haul didn't flash.... Only issues I've had is when shifting from P to R, it takes a second or two longer than it should and shifts hard when it does but it doesn't do it every time.
View 1 RepliesFast idle 6.7 when cold remote start. My GM had what could be called a auto fast idle when it was cold it idle a lot faster.
It appears my 2012 f350 does not , Ford dealer said he could install a fast idle using one of the switches.
And then if I park truck with park brake on and switch on it when I start it will fast idle to around 1300.
My question is being if truck is started by remote , will not this switch be off and by being off fast idle will not work , is this not the case?
So I have had this happen 3 times so far. As I am driving, and step on the accelerator, I get a very bad shudder in the engine. The whole front of the truck is jumping up and down. Once I slow down it stops and is fine.
It has happened on the following three occasions but it is intermittent and does not do it all the time:
1. driving up a long grade at 45 mph for 5 minutes. I stepped on the accelerator to speed up and it happened.
2. Getting on the highway from 45 to 70 fairly quickly.
3. Once I got on the throttle heavy and got up to 80 MPH. I laid off the throttle to slow down and when I stepped on the accelerator again it happened.
I was not towing at any of these times. I do have warranty still but since I cannot always replicate it, I have not taken it to the dealer yet.
The past month or two, my garage-kept 2011 F350 6.7 with 38K miles will shudder on startup for a second or two or three then runs normal. What would be causing that? She is my every day driver, but I don't drive her every day. Seems that the longer she sits, the rougher the startup. Last time I drove her was Monday. Started her up tonight to run to the store and she shuddered for about three seconds.
View 14 RepliesSo my 06 6.0 4x4 is just about to break 200,000km and I've done most of the upgrades and work myself. (All the updates are in my Sig). My problem is that when I'm cruising and the engine is at full operating temp, if Im bellow 80-100km/h nothing but as soon as I break into that speed range about 2000rpm the truck will start to shudder. Almost feels like its not firing properly is the best way to describe it. Why this could be happening or causing it?
View 7 RepliesAnything besides a worn out Torque Converter clutch that might cause the incredible amount of shaking when the transmission tries to lock the TC?
View 6 RepliesRecently had a rear pinion leak and replaced the seal and nut. I jacked up the truck, took off wheels and felt the drag so I could duplicate once i had the new seal as I tightened the nut. I've done this only once before on my F150 years ago, but when I put the driveshaft back on and test drove it, i had shudder when not under load. So when I let off of the accelerator, it had shudder and more the faster I was going.
Obviously thinking this is a preload issue with the rear axle but would this be caused by tightening too much or too little. I had no issues before so I would think that the driveshaft itself is not the issue. I can't confirm that I got it bolted up in the exact same manner as before in relation to the flanges but still wouldn't think that to be the issue.
I bought my f 350 new from the dealer and have had many of the problems associated with this truck. Now I have a severe shudder while under acceleration when i either let off the gas or increase speed the shudder goes away. My dealer thinks it is injectors but I have little faith. Shudder seems to be rpm consistent and seems to be in the front end. oh yea it idles great and runs great except at that specific range.
View 4 RepliesWhile I am loving the fuel millage and ride of my new truck, I have my first concern. In the last few weeks i have hauled a truck bed full of dirt, and 3300 lbs of sod. both times i would use tow haul mode, and while the truck had plenty of power, it would shutter when accelerating from a stop. Mostly first gear 0-15 mph.
This is my truck with a fancy electronic controlled transmission, so on the old pickups this would be a torque converter slipping, but all the ford dealer wants to tell me is "its electrical and they want to reflash my transmission". I am at 26k miles and have less than 10k left on my warranty...
Truck had been running with a bit of a skip and shuddered after throttle was applied and then stopped (would drop to 400 RPM and shake real bad). Had some misfire codes so I decided to do some digging. Where to start looking for air leaks pre upper fuel bowl?
YouTube.....
Also, does this mean the air has toasted my injectors?
YouTube.....
So I picked up a 53' for the racecar. When I'm hauling it on take off I'm getting a pretty good shutter out of the truck. My crew chief who owns a maintenance shop, said it's a known issue, and ford has been shimming the drive shafts.
I talked to the service writer at my dealership and he said it's a known issue and they are working on it. However, he said if they shim the driveshaft, there is a good chance it could fix the problem loaded, but then unloaded I'd have the problem. Is there a setup that's recommended?
I'm towing about 15k, but that's far from the limit of my 450.