Ford 6.0L Power Stroke Diesel :: Coolant Started Spraying Up On The Windshield Suddenly
Jul 9, 2015
I was out for a short drive this evening and got on it just a little bit to hear that wonderful 6.0 sound and all of a sudden coolant started spraying up on the windshield like I was spraying it from the windshield wipers! My first thought was oh crap I've got a blown head gasket and it puking from my degas bottle. I had a short drive to the house so I eased it on home. My ECT got to 226 with the fan roaring but not cooling it down, luckily it never got over 226. When I got home I opened the hood expecting to see where a bunch of coolant had puked from the degas but instead I saw this. What could cause the radiator to rupture like that? I did spend a good amount of time on my knees on top of the radiator while changing out my oil cooler the first time, then again when I installed my BPD oil cooler. Also I posted in another thread a few days ago about my ECT temps being a little higher than normal, reckon my radiator was clogged and that caused the higher temps and the rupture?
View 8 Replies
Advertisement
I turned the key and it started to crank and slowly started to whine down. Tried it a 2 more times and it did the same thing only with less strength and on the third try all I hear is the starter clicking. Both batteries read 12.57 on my multimeter while not cranking. Does this sound like an alternator? All my electronics seem to have plenty of power.
View 14 Replies
I have coolant blowing out of my coolant reservoir when ever i hold it to the floor it does it with or without the banks programmer... 6.0L power stroke...
View 14 Replies
Well got home and the front of the truck was covered in coolant. I must have driven 2 hrs after I noticed no coolant pressure, but temperature was great so figured it was another crappy cap. Looking to get a quick turnaround. Need to go out of town for work Saturday so I have this week to get it done.
Just put a stock unit back in? I don't think I need to do anything else in that area. Belt/pulleys/radiator all done last spring.
View 9 Replies
This weekend my friend and I plan on doing a coolant flush, new Mishimoto thermostat housing with high temp thermostat and install a Mishimoto coolant filter.
Truck currently has some unknown green coolant in it and Im going to replace it with Rotella ELC. I plan on doing a couple hose water flushes then follow with about 5 distilled water flushes. I've been reading about putting some Cascade in on first flush to dissolve any silicate goo that might be in there hanging out. I might give that a try. Im sure I can manage this part from all the stuff I read about doing flushes.
This is the part that looks like a little more work involved than the flush. Doing the thermostat kind of worries me because of the tight area in there to work with the fuel line and the EBP sensor being right there. The current thermostat holds temps around 175-185 under normal driving. I bought the new Mishimoto thermostat housing with the high temp thermostat installed in it when they had their pre sale going on for the housing.
I decided to just go with the whole thing because of all the stuff I read about people having issues with the thermostat not fitting the older housing correctly since Im certain I have the original housing from 2004, like everything else that's still original on my truck. I plan on removing the thermostat before doing the flushes and then installing the new housing and thermostat and coolant filter before I add the ELC.
The coolant filter install looks fairly simple to do so I should be ok with that.
View 11 Replies
I am fairly new to powerstrokes, but have a general understanding how the 7.3l operates, and how the fuel system works.
The problem i am experiencing is a crank, no start. The truck has been great for the year and a half that i have owned it. Always cranked great and never any starting or running issues. One day upon cranking, i started the motor; it started normal running good for a minute until the motor suddenly started shuttering and then the motor shut off, happened rather quickly. The truck started up immediately after that and died....repeating the shutter until dead. Now the truck will not start.
Specs on truck:
2002 7.3l
230,000 miles
Manual transmission
Here's what i have replaced so far:
New parts include:
IPR (motorcraft)
ICP (motorcraft)
EBPV (napa)
CPS (napa)
IDM (reman)
Here are some of the diagnostic values i have collected during cranking: (FYI: i am a little confused on what the values mean and what they should be in order for the motor to start):
ICP: 2218 psi
ICP duty cycle: 41%
EBP: 265 kpa
battery voltage: 12.0
Rpm: 355
Things i have checked so far:
Oil is new and level is good.
WTS light cycles as normal.
Fuel bowl is full and over flows with cap off while cranking.
Fuel tank is above half.
Glow plug relay is good.
I was throwing a code for the PCM, but i removed the bully dog tuner and the code has since cleared.
HPOP oil is an inch below full.
I made a gauge set and dead headed HPOP yielding 1500psi.
Upon cranking i am seeing some smoke, i guess, but its kind of hard to tell from the drivers seat.
This is where i am at so far. I don't have a way to buzz test the injectors or tell if they are leaking past the orings. I have the valve covers removed, but i have been putting off pulling the injectors to replace the orings.
View 14 Replies
I have a 2004 Super Duty with a 6.0 diesel. Recently the windshield washer seems to have lost some of it's spray power. It still sprays, just not very hard. I know it's not frozen, as it started this before it got cold.
View 3 Replies
After 2yrs and 1mo, my DC power 270XP amp died. I put the almost 10 yr old factory alt back on and everything is good again, except for the glaring fact that I have a dead alternator. It is a month beyond warranty (of course).
Truck has been running great. Oil cooler, EGR bulletproof cooler, STC done in Dec at Ford due to high deltas. I have a small stereo - one 12" sub woofer, otherwise nothing that really stresses the electrical system. I did the "big three" with 1/0 copper - cost a fortune, saw no difference - but that could have been an issue for the alt.
I left a message today with etch support but did not get a call back. I hope they make good on this - I waited almost 4 mo's to get this thing and it was supposed to outlast my truck.
View 14 Replies
The black rubber trim around the windshield is coming off on the top of the windshield. Vibrating away at an extremely annoying tone.
Been that way for a while just a small section, I'd just super glue it down and it would hold for a 1000 miles or so, then I would just do it again until it came off about 1/2 way across. At that point I just used Gaffers tape across the whole top - looks okay dark area of the truck and Dark red paint makes it so you cant notice the black tape at a glance. now that its getting hotter that's not holding but for 500 miles, which is about a week for me and gets annoying to have to stop on the fwy to fix it.
So its time to fix it right, but how?
View 4 Replies
(04 FX4)... having issues with your windshield washer? The next to last time I used it, I got a dribble, so I figured that I needed fluid...added more fluid, but it was still half full, I pressed the button, I heard noise, probably the pump. but no fluid. Could it be something as simple as a clog? I could tear it apart.
View 12 Replies
On my 2000 OHV Explorer the windshield washer just dribbles. I purchased a new pump and still dribbles.
I took the nozzles and pump from my 2000 SOHC Explorer that worked great and put them on the OHV one and still dribble.
I even cleaned out the lines first. How to get these to function properly?
View 4 Replies
I have an 05 Excursion that has a rebuilt stock turbo on it, installed before I bought the truck. I installed a 3.5" downpipe/4" after exhaust with no cat and no muffler about a year and a half ago. It seems like suddenly my truck is whistling a lot more than it used to at idle. I'm not unhappy about the whistle sound, just wondering if this is possible (i.e. turbo vanes sticking or something else) or if I'm imagining things.
View 5 Replies
Blows cold, so not a freon issue, but it will sometimes just suddenly stop blowing cold as if I punched the "A/C" button disengaging the compressor. Sometimes if I just wait a while it will come back on by itself, sometimes I have to stop and shut the truck clear off and take the key out, then start it back up and all is well again and it blows cold again.
High pressure switch failing???
BCM issue???
View 6 Replies
I've had my F350 SD for 6months now(21,000 mi) and have seen probably 20 times when I insert the key and turn the switch on the windshield wiper's will make one swipe when NOT turned on. Also have seen several times when starting the truck the radio comes on and it was not on when I turned the truck off. Yesterday when I finished work and was heading home I started the truck and the wipers came up about 1/3 of the way and stopped. I can't seem to duplicate the problem so I have not scheduled it in as of yet.
View 14 Replies
2011 ford f350, 200,000 miles. I was getting an antifreeze spray on the windshield while pulling and going up a hill. It was from exhaust pressure going into the coolant system. It was building over 16 psi and blowing out the degas bottle.
View 14 Replies
No matter what I do with the settings for my heater in my lariat air only blows out of the dash vents. Defrost and floor vents don't work it still blows hot air out of the dash vents. I'm not sure what the deal is maybe the vacuum system? I did a search and all I could find was people having trouble with air ONLY blowing out of the defroster and my case is just the opposite.
View 8 Replies
Had a lot of snow in the North East last week. Tried to use the remote start three times without any luck. Cleaned off the windshield and it worked. At best the remote is a weak system with very little range. How to use it or make it work better?
View 12 Replies
Looking for a video or directions as to how I replace a windshield wiper motor on a 2006 SD?
View 2 Replies
6.7L ... Just traded in my F250 on a 2011 F350 Lariat. Love it. Period. Except that my windshield wiper sprayers will not work. I don't hear anything when I hit the button. No click or motor running. I can't figure out what fuse it is because I don't have an owners manual.
View 14 Replies
This morning, I started my truck to go somewhere and less than a minute into my drive, the engine suddenly died. I tried cranking it again to which it started but less than a second later it quit again. That's when I noticed my FMP on my SGII was at 0v. When I got it back into a parking spot, I pulled the FICM and tested the connectors as well as the relays and they all were normal.
I decided I will be pulling the FICM again tomorrow and I will be sending it back to FICM repair.com for them to look at as I got a new one from them about 8 months ago. However if it is in case the wiring harness, where is a good place to look. I don't think it is the wiring harness as it seems to have voltage at the connectors.
Also this may be related but earlier this week, my Scangauge froze and I unplugged it and plugged it back in and it didn't connect to the PCM until I reset the SGII to factory settings. I wonder if this is related?
View 14 Replies
Driving home from work last night my truck just died. I was under load, going up hill, and she just shut down. No power, completely dead.
She'll crank, but not start.
Ever hear of this?
View 14 Replies
