Ford 6.0L Power Stroke Diesel :: FICM Sync Taking Longer Than Usual
May 1, 2016
I've had my 6.0 for 2.5 years now and got really acquainted with what makes what noise, and how long starts took etc. recently this morning, i had a longer start, longer than a normal long start (4-5 seconds). Felt too long to me, but it started and didn't turn it off to try again. Got to my destination, turn the truck off and brough up ICP, FICM, FICM SYNC and cranked and watched.
After 1 second ICP jumped to 600 then to 770 and 2-3 seconds later FICM sync finally read 1 and it fired. What can be causing the sync to take so long? I have had intermittent no starts before, maybe 4 in the 2.5 years i've had it and every time i have pushed on the fuse blocks by the driver batteries, and also pushed on the FICM connections to make sure everything was okay. That seemed to always work.. But no amount of pushing on them are solving the long start that is happening...
View 3 Replies
Advertisement
2004 6.0 Truck has been slow to start and sometimes took a few tries to get it to fire up. On monday the Truck would not start. The FICM was not getting sync. I figured it could be a bad connection to the FICM. I pulled the FICM, cleaned the contacts and reconnected it. The truck fired up. It ran all day Tuesday without incident but wednesday morning it would again not start. Again what was missing was FICM sync. This time disconnecting and plugging back in the FICM did not fix the problem. I have spent the last two days troubleshooting and am out of things to try.
The problem as it stands right now
The truck will crank but not start. Scanner says it has oil pressure, a steady 48v (FICM has new power supply). The IPR sits around 50% when cranking at 1200psi. However, the FICM will not get sync. I have worked my way down and tested both the Cam and Crank sensors from the PCM. The Crank sensor has a resistance of 360 ohms and produces a AC voltage of 500mV when cranking. The camshaft sensor produces 100mV AC when cranking (camshaft sensor was replaced as the original produced AC voltage seemed low 20mV, new sensor produces 100mV). I have tested the camshaft sensor at the sensor and at the PCM connector. This has lead me to believe both the cam and crank sensors are ok and their signals are being probably transmitted to the PCM.
I have tried to check the inputs to the FICM to confirm the signals are getting there. I was unable to find a good pin out diagram for the 2004 FICM but what I found told me the crankshaft was pin 5 and the camshaft was pin 10. When cranking, pin 5 (crankshaft) did not produce a signal and pin 10 (camshaft) had a 200mV DC signal. Despite searching I have been unable to find what the input signals to the FICM should be.
Right now I suspect bad wiring between the PCM and the FICM, or a bad PCM. This is based on having good signals to the PCM, but (what I think may be) a lack of crankshaft pos. sensor signal to the FICM. I am specifically looking for what the crank/camshaft pos. sensor signal at the FICM should be, as well as confirmation/disconfirmation on the diagnosis of bad PCM or PCM-to-FICM wiring
Truck Details
Ford F350 King Ranch 2004 6.0
Truck build date 11/18/2003
350,000 km
Studded
New FICM power supply
Stock truck; don't run any tunes
View 14 Replies
I have a 2006 F350 with around 208k mikes, automatic with a no start, 0 No FICM Sync.
The CMP and CKP has "no / 0" for synchronization and a "NO" synchronization from the FICM. Should this be "yes / 1" when trying to start?
The camshaft position sensor status indicated "yes fault".
FICM is at 48V,
DTC currently on
P2614 camshaft position signal output/open circuit - CMP
Glow plug circuit cylinder 2, 4, 5, 6 (these have been on for 12months and 1,000 miles and never had an issue starting)
B1352 - left front temperature damper motor
B1360 - left rear temperature damper motor
U1900 - CAN - communication BUS fault
I am running all OEM filters
View 14 Replies
04 6.0 with no FICM sync and no fuel pulse width. Crank/cam sync yes. All other data is good. Tried known good FICM and PCM but nothing. Had glow plug codes thats it. Found chaffed wires due to mice. Replaced damaged Injector harness still nothing. Fuel pressure is good btw.
View 13 Replies
My 6.0 2005 Excursion has been running great lately except for an issue starting last week. I go to leave work and it cranks over-and keeps cranking over. I fire up the torque pro app and see that I have no FICM sync. It just reads 0. I pop the hood and fumble around the FICM connectors. Try cranking again and it cranks and cranks and finally kicks in. I have not had this happen since but am paranoid now that this will occur again in the worst possible place and listen to everyone in the family tell me to get rid of my prize and get a newer truck. I monitor quite a few things on the Torque pro app but could others chime in what I should be monitoring in the meantime to try and solve this issue.
View 4 Replies
2007 6.0l cranks but no start. Read all the forums and I think I performed all the checks. Getting a ficm/ cam sensor/crank sensor no sync. I'm also getting 84.70% at the ipr while cranking. Do I have multiple problems? Watched videos on either the ficm or ipr percentage but not one that had both problems. Getting injector clatter and fuel pump runs. Didn't see anything obvious with the harness.
View 14 Replies
2003 accent. I had an intermittent starting issue, nothing serious. Then one day dead in the water. Had it in my garage so i changed all belts, Crank position sensor, starter and solenoid. It seemed to start different, a little longer than usual to start, but started. Drove it for about a week and dead again. Dont know if it was chance or not but as weather got colder, seemed to take a little longer to start. Cranks but does not fire. I can hear fuel pump priming. I took the spark plug wire and held it next to frame and did not see a spark. To double check i tried ether and still would not turn over. Assuming fuel is not an issue at this point. How ever i did get an evap code p0441 but it went away. I am stumped at this point. I am not very good at electrical on vehicles. I want to check coils, and work my way back but not sure if I am doing it correctly. Most vehicle videos don't have the same parts.
View 13 Replies
Ok I've got an 01 F250 sd 7.3 with 257k on it it just started talking longer to start than it should it will do it cold or hot even if I shut it off at the drive thru takes it like 10 sec or more to fire. My question is I thought about purchasing a autoenginuity to find the problem but not sure the best place to get and what model I should get.
View 7 Replies
According to the scan gauge... I used to run about 195-200* all the time no matter what.
Now days i find myself up into the 220s and with my boat on ill see 235 climbing a hill.
Good deltas between the water/oil temps.
I wanna get back to my 200's.
I pressure washed out (on low) the front radiator and all the coolers, I didn't get much out and they didn't look dirty.
I am thinking water pump or plugged radiator?
View 14 Replies
I replaced injector couple weeks ago. I hooked up to livelink thru sct because it was throwing a low voltage for ficm code. It is staying at 48 volts tho. I don't see any voltage from my glow plug relay, and I have a low voltage for my egr valve. Is it just bad luck that everything broke at once or is there a fuse or a connector that I forgot to plug in.
View 10 Replies
If my ficm is going bad will it cause it to jerk going down the road and spit and spudder going down the road..sounds like injector but it aint smoking at all.. I think there;s a recall for the ficm for my truck too.. f250 2004 6.0....
View 3 Replies
2003 6.0, all stock. Crank, no start with an occasional sputter when it actually shows FICM SYNC = YES.
It had the following relevant DTCs when I scanned it:
P0261, P0270, P0276 and P0279 - Cylinders 1, 4, 6 and 7 - Injector circuit low
P132B - Turbocharger/Supercharger boost control A performance
P2614 - CMP Open circuit
P2617 - CKP Open circuit
CMP/CKP SYNC transitions to and maintains YES while cranking, however FICM SYNC transitions back and forth between YES and NO while cranking. When it transitions to YES, a cylinder or two will fire when FIPW comes up, but FICM SYNC almost immediately transitions back to NO.
Based solely on the scan tool results, Cranking shows IPR DC at about 50%, ICP PSI ~1500, ICP V ~2.0. These are stable and steady. FICM main power is at 49.5v and drops to 49.0 when it fires the occasional injector while cranking. RPM reads above 150 while cranking.
I'm thinking that since CMP/CKP SYNC stays YES and is stable and RPM reading is consistent, the CMP & CKP sensors and circuits are most likely good. I'm thinking with the codes for injectors 1, 4, 6 and 7 it probably points more toward a FICM issue.
Another thing that may or may not be relevant is the pre-cycle clatter sounds off to me. With an ambient temp of about 70F, the pre-cycle seems to repeat 3 times. The second and third cycles sound worse than the first. This is in the video below.
I work on far more 7.3s than I do 6.0s, so I'm looking for anything I may have overlooked, a second/third/fourth opinion, or if there's a flaw in my logic for someone to point it out.
6.0 No Start - YouTube
View 14 Replies
My ficm has been dropping to 44v occasionally so I have ordered a 270a alternator from Ed at ficm repair along with the complete battery cable kit. I also took ends advice and bought two new odyssey 65 series batteries. I went with bpd 6phase ficm though because I like the idea of the extra phases to share the load and back up the 4 primaries. I am also doing the blue spring upgrade while under the hood as well.
So my question is this.... My truck is bone stock no mod 53k mi. The bpd ficm can be set to 48,53 or 58 v. I do not see the need to do 58v but have seen a lot of guys doing the 53v option. What is the advantage of 53v? I know if you run 220 thru a 120v light bulb it will burn bright as hell for a little bit till it blows, is this the case with running a higher voltage ficm? Will it eventually wipe out injectors? Or even the ficm processor board? Should I just stay at 48v setting?
View 14 Replies
This is the second time this has happened to me . Truck runs fine shut it off go to re start and it's a no start. I can watch the ficm volts drop to 0 from 48.5. Then it's 0 until it decides it gets power again?
View 8 Replies
I'm afraid my FICM is on its way out. I'm getting voltages dropping to 46.5V about once a minute. Never goes below that. Then it'll bounce up to around 48.5. It gets low when I have to rev up and always coincides with the main voltage dropping to around 12.9V.
Now for my battery condition. They are about a year old. I think I have one with a bad cell. They'll drop into the low 11V range while cranking after glow plug light goes off. While driving, the main voltage never gets below 13.1 except for very short periods ... which coincide with the 46.5V output on the FICM. Gonna have them tested separately at advanced auto and see on has a bad cell.
So, is my FICM starting to go? Second question. What do I tell the folks at Advanced Auto about replacing both an not just one? I suspect they'll want to argue about it with me.
View 14 Replies
So, I was on a road trip to Arkansa from Missouri when my truck started loosing power and eventually just died. After I tore through some stuff, I realized the ficm was just floating around off the brackets and even better yet, missing the top cap where you voltage test. And to my great luck, there was a small coolant leak that dripped it's way right into it.. So now I'm looking at replacements and it looks like I'm going to go with the Bulletproof Diesel ficm. But my question is, can I just swap them out and go.? My truck is tuned with an SCT tuner and was tuned up when it died. Should I tune it back to stock before I put a new one in or put the new one in and then put it stock and retune it after that.? Or is it more complicated than that and I should just let my mechanic deal with it.?
View 12 Replies
I just bought a new to me, 2005 ford f-350 6.0L turbo diesel with 220,000 miles. It has an EGR delete, and aftermarket intake and exhaust. I am having power loss issues, and cold start issues, and judging from these symptoms, I figured it was the FICM. I thought it had to be the FICM. As per the tech folder on this site, I tested the FICM. I first learned that I have one of the Bullet proof FICM's, and when I tested it (3 times) it read between 57.5 and 58V. I conducted this test three times both with just turning the key, and with the truck running. I then took the truck into Ford, and they gave me a list of all of the codes the truck threw:
P0611
p0113
p0405
p0671
p0673
p0675
p0677
p0341
I researched all of these codes, and it seems to point to the FICM, but Ford stated they pulled a reading of 54.5v. The tech then told me that the upgraded bullet proof FICM probably ruined my injectors, because my injectors we not upgraded. Is this True?
Even though my FICM is above the low limit for voltage, can it still be going out? I am taking the truck in to have the batteries load tested, so I will know if they are contributing to my FICM failing.
View 13 Replies
Well, coming home from work Friday and my truck turned on the check engine light. I did not notice any loss of power or other driveability issues. When I got home I pulled the DTC's. I got P0264, P0273, P0276, P0279, P0611, and U0306. The first four being low voltages. The Second FICM. And the last cylinder 6 misfire.
I sent a message to Ed at FICM Repair asking if there was anything to check before I pulled the beast. He said no it needed service no matter what at this point. BUT, I needed to test batteries and alternator. So I spent some time today pulling off my FICM.
I went ahead and pulled the EBP sensor and tube off from the exhaust manifold. The manifold end was very clean. BUT, the sensor end had a noticeable restriction. I would guess a 40% restriction. I cleaned the tube and the sensor and put it back on.
Next I moved to the EGR. I pulled it off and it was dirty but not what I would call restricted. The valve moved freely. I cleaned it anyway and blew out the manifold before I reinstalled it.
I have the batteries on a charger right now. Once they each charge for 12 hours each I will let them sit a day or two before I load test them. They are about four years old, AC Delco 60 month 875CCA batteries. I have had problems the last 6-8 months with staring the truck. If she sits for more than 3-4 weeks without being run she turns over slow and won't start. So I have had to jump start her a few times. And before you ask I have done a parasitic check and only have .05amp draw. So maybe the alternator is getting weak.
On that note I pulled the alternator and will get it bench tested this week. While I was there I noticed the top grooved and smooth idler pullies were a little "wobbly" so I yanked them too and will replace. Might as well do the belt while I'm at it. Boy this is going to get expensive real fast.
So, I decided to go ahead and replace the bottom coolant recovery hose and the long hose/pipe heater hose too. Boy it never ends. Oh well. I would rather do it now while I have stuff pulled off and it is easier to get to. Ordered those parts from RockAuto to the tune of 219 dollars. OUCH!!!
I accidentally broke my new engine oil dipstick while I was trying to get to the FICM!!!! CRAP!!!! More money. So......... Is there anything else I might want to look at while I am there?
The truck is 2006 F250 6.0 PSD CC SB 4x4 mid optioned XLT with 108,000+ miles. I have a 4" turbo back exhaust, AFE Cold Air Intake, Blue Spring, Hypertec Power Program 3 on the lowest setting, and an after market intake elbow at the intake manifold and an engine oil bypass filter. Turbo was pulled and de-coked about 18,000 miles back. Otherwise no issues. The 90,000 mile service was done about 10,000 miles ago. She gets regular services.
How about methanol injection? Will that keep the intake clean from the EGR sludge? I'm not thinking about added power, just keeping things cleaner? I plan to do the Atlas 40 when the FICM gets repaired.
View 14 Replies
Couple days ago the cab of my truck started shaking some more than usual. Its gotten worse now, however. Happens the worst around 60-80km, light on the throttle just cruising in overdrive, whole cab shakes badly. Chop the throttle and its completely gone, any heavy on the throttle and it's gone as well. Does it loaded and unloaded. Okay at highway speeds but like i said around 70km its bad. I've got my guesses but what really it is?? Truck runs fine otherwise...
View 14 Replies
So after replacing all injectors, I was getting a rough idle and drive. Got an imbalance on 5 & 4. Cleared out codes and 5 still showed. The guy doing my work and I couldn't trace it to anything so we thought well maybe we got a bad one. Did fail the buzz test. So got a warranty one and put in. Wouldn't you know it's still not running quite right. Only thing we can think of is maybe the ficm is at the start of going out. Voltage reads good still though. Staying constant at 47/48. Is more noticeable to run rough when starting from cold then smooths out but you can still make out/feel an injector going in and out.
View 14 Replies
I have a no start on my 2003 6.0. What I've discover is that I have two issues, ICP pressure is low and the FICM is not syncing. My plan of attack is to fix the sync problem first then the ICP issue. FICM main power is good holds at 47.32 during crank but it has no FICM sync, I've check the camshaft position and crankshaft position sync status and it returns a value of in sync, it also reaches a max rpm of 257 during crank. Given those two values I think the cam and crank sensors are good. I did a visual inspection on the wire harness and can find no chaffing, shorts or hard bends. I think I either have a bad PCM or FICM. How I can narrow it down to one of the two?
View 14 Replies
