This morning when attempting a cold start of my 05 6.0, it would not start was noticeably harder cranking. I had no CEL. I checked my scan Guage and the volts were 13.4 and fcm main power was 48.4. I checked and I had a p0405 code. What could be going on? I read that it can be a stuck or bad EGR valve? Could it be battery related?
View 9 RepliesSo I have an '03 6.0 with 151000 and change. I go out to light her off in the morning and she fires quick and easy. Idles well and no complaints. But when hot shes sluggish to start. Now it's not what I would call a typical hard start considering I've watched videos on YouTube and guys are having a lot harder of a time then me getting theirs started. It's just not the same as cold it almost sounds like it's lacking fuel cause it starts real low after fire then with a couple revolutions it perks up. And this is without the key still in it. Again no idle or running issues at all. I've been trying to see if it could be my ipr? My ficm is new and never gets below 47V but idk what it is.
View 14 RepliesI have this problem code P0405. At fist it come up with a turbo under boost. I have replaced the Turbo and egr valve and I still have the P0405. I did notice a oily residual in the port for the egr valve I see no deference in coolant. She idles good I just have no power when I put it in gear to move.
View 3 RepliesBackground on the vehicle, Last week installed Swamps 200cc/30% injectors with a 38r. Had swamps reburn my chip for the new upgrades.
But heres the problem i noticed starting the truck was a little harder ( longer cranking ) till it would start never thought of anything since i read air gets in and can cause it but then yesterday and today its taken 30 minutes to start the truck since i have to do a trial and error.
The truck just seems like the batteries are being drained or something along those lines. i also noticed my gauges keep resetting back to blue( default color). Today I plugged a battery charger up all good voltage i charged them so both read 14v and still no start. So a couple of attempts at starting with chip in and ICP on nothing
I unhook the chip and ICP get a half start then eventually it starts. After then i can hook it all back up and it starts good for the rest of the day but for what ever reason after it sits all night it doesn't want to start up right away. I'd like to figure it out today since id rather not wake up at 4am and attempt to do this all before work each day.
I noticed that my gauges would reset to the default color after each turn off. So i unscrewed my ECU and then redid that to make sure its tight. along with making sure the chip is seated properly. after that it stopped resting my gauges. Whether that's the issue or not i cant say but ive been checking my HPOP oil level since i stopped driving it around 1400. and hasn't changed oil levels are good. I plan on starting it before I go to bed around 2200-2300 just to check and see what happens.
Truck was starting good, then slowly got harder to start. Now it will not start. I do not know what to check next.
HPOP 3700
ipr 46
FICM 48V
rpm sounds good.
Injector pulse 0. not sure if I have torque app set up correctly for that one.
No smoke and I pulled the top fuel filter and drained the fuel. took about 3 seconds to fill the housing with fuel.
Air filter gauge says it is good.
Still checking where to go.
Can a leaking Y Pipe throw a P0299? Dealership says that is my problem. My MAP at idle is 14.4 EBP is 17 - 18. At 60mph MAP is 20 EBP is 26-28. Boost is 10-20 .. Truck drives great no apparent issue. P0299 only code and appears when cold first start of day. If I clear it it goes away for the rest of the day and only comes back occasionally. Twice in 5 days only at cold start. 2005 F350, 100% stock, Ford filters all. Scan guage 2 for readings....
View 10 RepliesMy '05 Excursion recently started having rough idle and some loping when started cold. It seems to run good and idles pretty good when it warms up. I'm also getting a P0488 code (EGR Throttle Control Circuit A Range/Performance). I do have a BPD EGR and I don't recall if that would throw a code alone? I'm taking a trip next week and want to get it straightened out. Does it sound like an EGR valve issue?
I also thought about a battery issue, I know that can cause weird problems. I have Duralast batteries and they always seem to fail at about 2-3 years. I took it in and they say it tested good but I'm not always sure with them. Long story, but when cranking for longer than normal, the cranking power would drop quite a bit. Checked battery and had some corrosion. Cleaned and upon further inspection, the positive post is a bit eroded at the base and sunken in. The voltage was about 12.35 after sitting all night, a couple of the cells were reading lower than the others (about 50%, other 75%) when checked specific gravity. I tested voltage after batteries had been in the truck overnight, then unhooked from truck when testing.
I also thought about a glow plug/harness issue. The truck cranks for awhile before starting, 5-6 seconds sometimes, but not all the time. It starts up pretty quickly when warm. That's been going on for some time. Anyway, I will try to get a video of the rough start after cools down.
I have a 06 f250 king ranch with 6.0 . A few days ago my scangauge showed a code P0405
I changed my egr and after it showed two codes : P0405 and P0404
It still has a hesitation and loss of power , although better than before the Change.
Scangauge reads icp ok. Ipr ok. Fmp voltage is all over the place from 42 down to 2. Flp is also all over the place from 11 down to 2 volts. And no Sync. Load checked batteries well. Voltage is 11.5 down to 10.5 when cranking. Fuel good. No pre warning signs. Parked running good. I have read tones of forums but none with 3 issues. Could it be the relay?? Would a bad ficm show no sync on cranking?? Why is my flp voltage so up and down.
View 14 RepliesFinally got everything buttoned up, and truck was going for it's first drive today. Started cranking, and it just barely tries to start, and then nothing until I cycle the key again. Doesn't even give me a full Vroom, Just like a Vro- and then back to cranking.
I've had it started and running a few times, so something has changed. And to add to the fun, something between my tablet, my torque pro app, and my dongle isn't playing nice. Tablet just won't see the dongle. So I get to figure that out too.
I have a 2006 f250 superduty 6.0. The truck ran fine a week ago and than died as I was going to take it for a drive. I figured out that the fuel pump (air dog system) was not working. I fixed that and primed the pump. The truck still won't start. When it first happened the truck would crank but not start. Now all I hear is the starter but no cranking. Both filters could be replaced. The bowl to the upper is dry when I take the cap off. However fills up when you turn the key on. I'm not sure what else to try and I need to get this truck started.
View 3 RepliesI need to start ford power stroke, 2005 with vt365 engine, is v8 cylinder, front timing cover was change and since then the truck only cranking and refuse to start, what have done so far, test icp power, ground and ecu 5 reverence voltage was ok,crank engine and monitor icp signal voltage was 1.2 and above at a crank,installed 1500psi gauge in icp hole and monitor oil pressure at engine crank reading 800psi and above, fuel pressure was 45 psi and above, check engine rpm was 175 and above, measure cam sensor ohms was 800 and crank sensor ohms was 400, check cam and crank supply power was 1.87v and ground was ok, replace ipr with brand new, no fuse that cut, scan for code i found(221 internal sensor supply voltage low or below normal range FIM4)FMI4,Engine crank but no smoke from silenser, using fluid and yet engine didn't make any attempt to start was only cranking, what could make the engine not to start and which component has failed that display above code.
View 14 RepliesHad Just replaced glow plugs and batteries along with a new set of tires. Truck had been running fine for the three days that is was. Went out the next morning and went to start and "POP" a large noise came from under the hood. I have yet to discover where this noise particularly came from or what it may have been that caused it. But ever since the POP it will not turnover what so ever. Key on every thing is normal all power just when go to turn key over it makes a faint click. You can feel the click in the relays on your hand when you try to turnover. But nothing. I am absolutely clueless.
View 14 RepliesDang, won't start again. My auction truck needed batteries, so I put mine in it and bought new ones for my work truck. Couple of days later, didn't start. Checked SG and I wasn't getting enough RPM. Jumped it and it fired right up. Replaced one of the new batteries and it's started fine the last few times, until just now, in the parking lot of the tire store.
The RPMs were weak - they'd go over 160 but then fall back to the 140s. I walked home and got my auction truck, jumped it, and it still doesn't start. Just spins. RPMs still fall back to the 140s after a few seconds of cranking, but they got as high as 220 so I don't think that is the problem. Fuel pump runs, the upper bowl is full, no bubbles. Oil pressure registers on the dash after a few seconds of cranking.
The last time, I wiggled some fuses and it started. Not this time. FICM at 48, ICP around 700 while cranking. Volts and IPV are good. FPW is 0, but I think that's right, until it cranks. Same with Sync - at 0 while cranking - does it ever go to 1 without starting?
It acts like it has in the past - cranking just fine but no start. And in the past, when it finally starts, it acts like nothing was ever wrong. I checked my IPR screen about a month ago after replacing it about 6 months ago when it didn't start. What am I missing? I'll go read some threads for clues.
I have now replaced hpop, injectors, cups, gpr, batteries, uvch on both sides, icp and ipr on my 2002 F550 and it still has a long crank to start.
It has been driven about 1,000 miles since then and no change. I have no codes except buzz test produced a high to low 1272 1274 1276 1278 one time. Cannot get that to happen again.
It is taking 4 seconds of cranking to start consistently hot or cold. It always starts but cranks for what seems like too long compared to my other 7.3s. I have included a screenshot of the data and am curious on what everyone's thoughts are as I am out of things to look at!
I just finished installing a new set of injectors, standpipes and the blue spring kit on our 2005 Excursion 6.0. The truck idles and runs much better but now it takes almost two seconds of cranking to start the engine. Cold and hot are the same and the length of time between shut down and start doesn't seem to matter either.
What to check? I am planning to check the ICP tonight when I get home. Could I have air trapped some where in the system? This is my first powerstroke so I don't know if this is a possibility.
About 7 months ago my truck started cranking longer than normal to start after sitting for more than 2 hours. This went on for about 3 weeks, then it started normally again. (By longer crank time, i timed it between 5-7 seconds on average. Normal is about 2 seconds). Now it has started doing this again about 4 weeks ago. Now I'm thinking HPO slow leak. Yesterday all is good again. What should I be looking for as a starting point to fix this permanently? When it cranks longer, the icp stays at 0, the ipr goes to 77%. Then it just fires off. No slow build of pressure. You can see all my mods and updated parts in my sig. I wonder if one of the new dummy plug o-rings is starting to give up already after only 15k miles. (Batt voltage is at 13.9-14.2, ficm is at 49.5 steady).
View 5 RepliesOK, long story short. I had P2284 code on my scan gauge after replacing the oil cooler. I contributed it to air in the oil system. Sure enough, a few days of hard driving and the code went away.
Now a week later, I fired up my truck on a cold start yesterday morning. It's not that cold here(low 40's in the morning), but the oil started off at about 50F. Correspondingly, ICP at is higher, at around 1000(it's like this every morning until oil warms up). I usually let it warm up a tad before driving but yesterday I didn't, and hit the gas pedal a little hard once and the truck started acting like it does when you get this code.
Sure enough, check scan gauge and the code is there. I drive home(about 15 minutes). A half hour later I start the truck up, check codes, and it's back to normal. Of course, oil temps were higher and ICP in the normal range between 580-590.
So is this normal? Since it doesn't trigger a CEL I assume it's more of a system parameters code? Only other thing I can think of, if this isn't normal, is a mucked up IPR screen from when I installed my BPD oil cooler.
2003, not deleted, everything was stock except for he put a Bully Dog on it with can tunes. Died on him was replaced ICP started up ran horrible was throwing different injector codes, IPR was at 84% at idle, plus had a lot of pressure on degas bottle.
Just finished studding, deleting, oil cooler, ICP, and injectors. She started up fairly easy, only to have the IPR still at 84%, ICP bouncing between 670s to 790s this just after start up from the work. Truck still runs horrible and still throwing #5 injector code also using AE and injector 5 wont Buzz. So, would be safe to say Injector harness and IPR sensor?
2012 F250 Superduty Lariat, 6.7 L.... While driving the cold air filter came loose and threw a CEL, code 2074. Corrected that issue, but CEL came back. Codes of 2074 and 2074pd. Cleaned both MAP and MAF and codes came back. Replaced both MAP and MAF and codes came back after about 20 miles. What are the next steps?
View 1 RepliesWell.. my truck has been running great for the past few years. This morning I went to start it and all it does is cranks and cranks.. no start not even a sputter.. I use the torque app and noticed the HPOP was over 900 psi during cranking and ICP volts were .8 volts. FICM was 48.5 and around 47 during cranking. I even unplugged the ICP connector and got the same results.. just cranks and no start. i noticed while it cranks i don't get any white "smoke" coming out of the tail pipe I even sniffed in there and I don't smell any diesel at all.
I pulled the upper fuel filter and it is full of fuel, the fuel pump does its normal buzzing when the key is turned on. I even checked the emergency shut off switch for the fuel pump and it was fine. At the moment I am charging both batteries... they were draining because of all the cranking. I think I will check the FICM with a multi meter when the batteries are good and charged.. Seems weird to be running fine with no hints of issues then all of a sudden its dead.