Ford 6.7L Power Stroke Diesel :: 2014 F250 - Exhaust Fluid System Fault
Jul 31, 2017
2014 F250 Diesel... I got the msg saying 50 miles until speed limited to 50 mph. None of the earlier warnings re adding def. check def on computer and it said it was ok. I even added def and it only took a small amount until it overflowed. It was more than 1/2 full. The error message did not reset. I drove it around for several miles and it still would not reset. Having it services as we speak, and the tech is still having difficulty running down the cause. He has done a regen,and reset the computer and etc and still has not resolved the issue..
View 14 Replies
Advertisement
I bought my 2015 F250 last November, and this spring my check engine light comes on with the message exhaust system fluid fault with the anoyying speed limitation. Bring the truck back to the dealer and they just say add def fluid, so I just have them do it. 2 weeks later the message comes back, bring it back to the dealer and they tell me it "needs reprograming" they do the work, light goes off. two weeks later light comes on again. Dealer puts in new exhaust sensors and reprograms the truck.
This fix lasts a few months in the mean time the truck shutters really bad under regeneration mode. Talk to dealer they claim its normal. Finally this week the light comes back on again. Bring the truck to the dealer and Ford keeps telling them that it only needs reprograming but that doesn't fix the problem. The dealer wants to replace the computer but ford isn't letting them do it (the truck is still under warranty) . I am starting to get pretty mad when I went out and bout a 65k truck not to have these problems.
View 6 Replies
My check engine light just came on and a few miles later the "exhaust fluid system fault" also came on. I plugged in my scanner and these codes came up:
P2479 b1s2
P2033 b1s2
P050E
P0231 b1s2
I'm assuming these mean bank one sensor 2 is bad. Need to verify? I don't remember all these codes when the #4 sensor went bad.
View 8 Replies
My 2012 F350 Lariat has 6100 miles on it now and on the way home tonight I got a "speed limited to 50 mph in 50 miles" message on the display. It states that there is a "diesel exhaust fluid system fault". The def was topped off about 2000 miles ago and the message center says that the fluid level is "ok". I am going to be on the phone with the dealer first thing in the morning. This is my personal/work truck and if I can't tow a trailer then I can't work. My guess would be a faulty sensor. I have no doubts that the dealer will get this resolved quickly as they have been great about everything else. I also want to say that other than this, I am sure minor issue, this truck is awesome!
View 14 Replies
Just wondering what this could be.its giving me the 50 miles to 50mph max speed. Def tank is half full.truck runs fine.
View 2 Replies
Set out for a 450 mile trip this morning. Checked all fluids, then checked the Edge CTS for any DTC's since it had been several weeks since I had driven the truck more than 100 miles per day. No codes except for a couple of P0000's.
Good to go.
45 miles into the trip while traveling at 75 MPH the chime sounds and the message center says "Diesel exhaust fluid fault. Speed will be reduced to 50 MPH in 50 miles." CEL on too. Using the CTS, I checked the codes:
P20EE - SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
P2080 - Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1
They were in the order shown. So the EGT fault came first, followed by the NOx fault.
I really need this truck today. Cleared the codes, but of course that didn't work with the 50 MPH limiting. Went back home and got the Jeep. The truck is about 1 mile away from the 50 MPH speed limiting.
It would seem that the EGT problem could lead to a NOx issue, but I could be wrong. I monitor EGT1 with the CTS, but I didn't see anything out of the ordinary. Also I thought an EGT fault usually gives the "Stop safely now" fault.
I did take a picture of the CTS DTC display before clearing the codes. Hope that will work for the dealer.
View 14 Replies
I had a ford technician plug in and check my CEL. Says P246E, Bank 1 sensor 4, exhaust system fault. I am leaving for holidays in a couple of days but dealer to busy before I leave. Is this something that will leave a guy stranded on the side of the road? I've already been towed once...
View 5 Replies
I just bought a new 2014 f250.
He says since he has purchased the truck the TPS sensor would occasionally go off saying there is issues with the tires. Tires are fine yet the light chimes on after being reset shortly. Been at the dealer for a week and they haven't really touched it I was wondering if there is any know issues.
Also my dad had the truck in 4x4 and when he puts the truck in park it made it a loud clunking noise. Ford is said there heavy duty line was full so they didn't look at that ethier. He needs the truck for the weekend so he is picking it up tomorrow, he will return it when he can but does this sound familiar as well?
View 7 Replies
Sunday I received the dreaded DEF system fault message on my 2012 CC SRW SB FX4 with 7800 miles on it. Warned me that speed will be reduced to 50 MPH in 50 miles. I have a CTS Insight, so I checked for DTC's. First one was P2200 - NOx sensor circuit (Bank 1, Sensor 1), the second one was P204F - Reductant system performance (Bank 1).
After 50 miles it warned me that speed would be reduced to 50 MPH on next restart. Sure enough, Monday morning speed was limited to 50. I took it to the dealer, but I should have left it running. When the service guy started it, the fault had cleared and it no longer showed the P2200 NOx sensor code, although the P204f code was still there.
My question is, why in the world would Ford make it so that the code is cleared if the fault goes away, especially after putting you through the 50 MPH limit scenario?
Dealer did a reflash and said its OK now, but I'm not so sure. My trucks build date is 10/6/11. I read TSB 11-11-13 which states the NOx sensor module should be replaced for P2200 on trucks built before 10/11/11. Is that only for a persistent P2200?
View 5 Replies
I've topped up the DEF and the warning is still showing that I'll have reduced engine power within 45kms.
Its weird, just yesterday it showed 550kms to empty so I added one full container, all day it kept showing less and less kms' til empty. Warning lights and bells etc.
This evening topped it completely and still shows. Is there a way to reset it without having to stop at the service dept.
View 14 Replies
I just bought a set of 2013 20" rims for my 2012 F-250. I can't seem to get the tire fault light to go off. I've gone through the "learn" process but it won't read them. Are the TPMS not the same between years?
View 2 Replies
I have a 2011 f-450 6.7 - truck has 70K miles. The other day I was driving and the message said "Cleaning exhaust filter ". I usually keep it running a little to finish. Then shorty after a warning message came on which said "800 Miles to Exhaust fluid empty". So I went to fill tank and it was FULL. Now the warning keeps showing up each time I start the engine. It now says 300 miles to empty. I'm afraid it's going to go into limp mode even though the exhaust fluid tank is full.
View 14 Replies
New 2015 KR. Has 2191 miles on it so far, 69 engine hours and 21 idle hours.
Truck is telling me exhaust fluid is under half full. I thought a full tank of it was supposed to last around 7k miles???
View 13 Replies
I'm new to owning a diesel. I have a. 2004 f250 6.0. I gotta smog the truck this weekend but the check engine light is on. Fault is P0674. I've notice during the day it starts up fine but at nights, lately it's been low 40 outside it won't start. Where to start at.
View 3 Replies
In the last year I've had a NOX sensor fault (dealer repaired) and a DEF heater fault (I replaced). I'm now getting an EGT sensor fail. Every fault is with the same system.
I'm also realizing that while I'm getting the exhaust system cleaning message, my DEF level is not being depleted.
All the dealership wants to do is change out fault codes but I think the true issue is elsewhere.
2011 F250 SD FX4 6.7L (stock)
View 4 Replies
Usually in the OBS 7.3 but a buddy of mine with a 2003 6.0 is having some issues. When he romps on the pedal but when he does so he claims he can smell exhaust in the ventilation system. I rode with him and smelt it as well. So I inspected all exhaust clamps and piping as best I could and did not notice any soot or leaks while running. I don't know if it pertains to it or not but his heater only works on defrost.
View 4 Replies
I have a new *to me* 2005 F250 and last night I noticed there is a leak around the brake fluid reservoir where it connects to the frame of the truck. Everything seems to be in good order not sure exactly whats causing the leak. It only when driving and for a short while after shutting the truck down, everything seems to be in good order but still it drips a lot.
View 9 Replies
Having trouble with 6.0 powerstoke white smoke out exhaust. We have installed egr delete and still have white smoke and water coming out of exhaust not as much as before. Took it back apart to see if we did anything wrong everything look ok. We did a compression test on all cylinders they check out ok.
View 6 Replies
New to Diesel trucks, have a 2012 F250 with 4000 miles on it. for the first 3000 miles I would see regular messages about "Cleaning Exhaust Filter" about every 100 miles or so, but this last 1000 miles I have not seen any?? I drive about 100 + miles a day, 55 to 65 mph so I'm sure I'm running it long enough.
The other thing I've noticed is that my MPG has gone from 17 down to 14 which is what I would normally see during a cleaning cycle. It almost seems like I'm in a constant state of cleaning as my MPG has taken a dive... Any things I should check?
Side note, I towed a 30ft RV around the 3000 mile mark, since the tow I haven't seen the message.
View 14 Replies
I have a 2014 F250 CCSB that I bought new, I now have 41,000 mi on the truck. Earlier this year it had the P207F code come up and subsequently the computer derated the power to idle. I was able to get it to the dealership and they could not figure out why the truck had this code come up, it is an exhaust fluid CEL. They went through a sequence of steps to include holding the RPMs at 1800 and the 2500 for about 5-10 minutes until one of the EGT sensors hit a certain temp, then the code cleared from the computer. They gave me the truck back and told me it would likely happen again.
Over the summer I had this happen twice more, however these times, I cleared the code, ran the truck at 1800 rpm, and the code cleared, all would be ok for a while.
Then about 1.5 weeks ago the truck had both of the mentioned codes pop up the same day, first was the P04DB, I cleared it. Then the P207F came up, it would not clear. I dropped it off at the dealership. They were initially quite responsive, and again told me that they could not find a problem with the truck from a mechanical standpoint. However, they could not get the light to clear and the truck was stuck at idle. When they were able to get the light to clear it would come back on in 10 minutes, the idle message has never gone away.
Now it has been at the dealership for 1.5 weeks, I am having issues getting them to even give me an update on the status of the truck and what they plan to do to fix it. They did provide me with a loaner, for which I am grateful to not have to rent a car. However, these are expensive trucks, and I need it for my farm.
View 14 Replies
I have been thinking about toying with my exhaust. I don't have a crazy amount of money. I got a 94 F250 with the 5.8 liter 351. Heres what I was thinking. Get rid of everything after the cat, and then run a single 3 inch pipe from the cat to a flowmaster 40 series, and then exit either right before the back tire or right after it.
View 7 Replies
