Have a 7.3 powerstroke won't start.. I have went through tons of parts check everything I can think of. I have put icp, our, fuel pump, fuel pump, injector, glow plugs and relay, fuel and air filter. new starter, new valve cover harness. HPOP is good and compression is good?
View 14 RepliesI have a 2000 F450 with a 7.3. I am having problems starting it. Batteries are good, engine turns over strong. It has started a few times after a extremely long crank (so long I am sure I am burning out the starter). I have replaced the CPS since it was cheap enough but that didn't make a difference. I have unplugged the ICP and it is very oily inside the connection. Does this mean the ICP should definitely be replaced? The truck will not start with the ICP unplugged. Should it be able to start with the ICP unplugged? Other items I plan on looking at at the IPR and possible the IDM box. Am I on the right track?
View 11 RepliesOkay a little update on my truck not starting, and for those who have not read my earlier post. My water in fuel light has been on in my truck for probably a month of use. I drained the water sep under the truck nonstop and added several bottles of water remover and the light would not go out so I assumed the sensor was just bad. (im new to owning a powerstroke btw) I broke down coming home from work, got it towed home, and still cant get it started. It will crank fine just wont fire up. I tried unplugging the ICP, i replaced the CPS, and ordered a new water sep/ fuel filter for under the truck. And the fuel filter on top was just replaced a month before breaking down. Every single time i drain the separator tons of clear water diluted fuel comes out before it turns greenish.
Not sure if this could be a cause of getting water in my fuel but one time i filled the truck up completely and it was like the water overfilled and probably a quart or two of fuel spewed out onto the ground. Not sure where it came from. Also I have just over a quarter tank so i was thinking maybe the float broke and I just needed to add fuel but today before i went to add fuel i drained the sep and tons of water came out... Im so worried about hydrolocking my engine or ruining my injectors. But I dont know if my issue even is water related if the sensor just went bad...
I want test my fuel pressure. What is a good gauge or kit to buy? My truck has lost power towing and is now starting to miss a little. I'm wandering if i my problem is in the tank. Is there a good scan tool that would diagnose things too?
View 14 RepliesI had issues with my F250 cranking last winter when the temperature dropped, so I changed out the glow plugs in the spring. I hadn't been able to truly test them yet, since it hasn't been cold, but the other morning my truck wouldn't crank up. It was 40 degrees out the night before, and it had been almost 24 hours since I cranked the truck, but it seems to me like the truck shouldn't have an issue in that mild weather.
I'm not sure what I need to do next to try and fix this problem, it's been driving me crazy and risks stranding me if I park for a while in an area where I am unable to plug by block heater in. The truck cranks fine when I have had it plugged in for a while, so I'm fairly certain it's a heating issue. I haven't done any tests since last year, but I know that the GPR was working properly last winter, which is why I changed out the glow plugs.
2001 F250 7.3l 294k miles
Ok so truck has always had difficulty starting cold since I got it about 12k miles ago. Replaced glow plugs, that made things slightly better but still no start unless temp gauge was in that first line above the C. Changed to Rotella, immediately after oil change starts better and at slightly colder temps.
Since getting the truck when you turn the ignition on you can hear a 'whistling' type noise which I believe is the fuel system pressurising. That used to last as long as the chimes did when you first turn the ignition on. More recently it lasts a lot longer.
Towed recently and had intermittent check engine light - believe this could be HPOP related, haven't checked codes yet as we're on vacation. No oil in the valley. But I do have a little oil carry over in the turbo intercooler pipes.
Truck slightly sluggish at setting off initially and then picks up reasonably well when not towing but my Dyno says I'm putting a bit more pedal to get the same performance from say two months ago
Pretty sure injectors haven't been changed since truck was new but can't be absolutely certain as there is no history. I was surmising this is probably both a HPOP and injector age issue but only from what I've found searching...
Got two brand-new Motorcraft batteries installed about a month ago and truck has been cranking great. However, the last couple days in the mornings the truck is starting slow and dragging as if the batteries are going bad. It does crank pretty quick but just has a noticeable starter drag now. Since I have no way of diagnosing the batteries with a tester over the holidays.
What are the odds that brand new batteries are going bad? I was thinking this is a starter issue since the drag is most prominent in the morning but it does it throughout the day while I'm driving driving on each start. But it's not as bad as the first start-up.
I hooked up a scan tool (Forscan and Dash Command) and the only trouble code I received that something to do with the turbo boost pressure fault, it was a code P1247. I don't see how a turbo boost pressure fault, low pressure, could have any starting related issues but you never know. Just a note this code only came up on my FORScan Lite app but it did not come up on the dash command app so I'm not sure if it's a legitimate code.
So I'm back to a battery or starter issue. Is there a way that I can check without much equipment to detect whether not I have a starter or battery problem. I do have a battery charger but no other equipment.
I have a 2000 Excursion diesel 7.3. I drove it for an hour yesterday and it drove great. When I arrived home I left the truck running and put it in park. Checked the mailbox and jumped back in the truck and put it in drive and it would not move. Tried FWD and reverse. Moved a little in reverse.
I turned the truck off then cranked it back up put it in drive and it drove fine..... Took it for a test drive and seems fine.
Did the same thing today. Went to drop my kids off and I put it in park and left the engine running. Put it back into drive and it would not move.
Turned the vehicle off and back on. Put it in drive and it drove off fine.
Fluid is full, red and no burnt smell. Wondering if this is converter or electrical and how long I can drive it like this.
While headed back to town my 2000 f350 7.3 with 444,650 miles (I'm original owner) and have performed maintenance and repairs since mile 3. Truck started to loose power and eventually stalled, was able to restart several times to limp home 7 miles in one hell of a snow storm. Very confused, replaced cam position sensor ( keep one in jockey box ) replaced fuel filter truck starts then stalls out. Don't know if a bad HPOP would allow start up at all. Fuel pump???
View 6 RepliesAm looking into buying a new transfer case (TC), and one web-site indicated there were 2 different automatic transmissions; Manual vs electronic -shift? So some TC's for 2000 AT's would not work? I found one (used) that was from a 2002.
My truck came to a grinding halt yesterday and I believe the TC. I had been hearing noise for a while and had been in the process of eliminating other causes (u-joints, ball joints) and think it was the TC all along.
I did not notice any issues with the AT prior.
2000 Ford Excursion, 7.3 PS with 210,000 miles. I am on I40 at a truckstop. I was rolling down the freeway last night when the truck started bucking. I pulled of the freeway and here came a thunderstorm. I waited til this morning to check for codes cheap scanner. I pulled a code P1211. I waited for NAPA to open so I could take it in the shorts. I bought a fuel filter and an ICP sensor. After changing them out, the truck runs then starts missing. My battery is about to die so I will finish post shortly.
View 14 Replies2000 7.3 Excursion. Truck ran fine on a 5 hour trip for family vacation. Pulled and to where we were going turn the truck off then what I had to do I came outside try to restart the truck for the next three days it would take 2 to 3 cranks before it was would start. Then on day number three tried six times and didn't start went to bed woke up the next morning and it took three cranks to start. drove it down to mechanic shop near me they have been troubleshooting and think it's an electrical issue the code is P1280; he said there were a couple other codes too and he would tell me what they were later but he never has. I took him a new CPS a new ICM and a new PCM, none of that fixed it. I am at my wits end here and really have to have my truck for work every day.
View 1 RepliesRecently I have had many problems with my 2000 7.3l .... The one I cant get rid of is the p1316 code. I have changed out the uvc harness and gasket with new ones, then removed valve cover's to double check connections again and they are fine. I am getting white smoke and the truck misses. I do not have a advanced reader for the codes just using my edge programmer. I have also disconnected the battery and cleared the code but it comes right back.
View 14 RepliesThe other day, I started having problems with the truck not starting when at operating temp. Went for a drive and stopped a a scenic overlook, and spent about 30 minutes taking pictures. Went back to the truck, and it wouldn't start. Outside temp was about 95 degrees.
I tried for about half an hour to start it, but all it would do is turn over. There was a work crew there with their heavy machinery, and I was able to borrow their starting fluid. One quick squirt into the intake, and it fired right up.
Although I do have an oil leak from the right valve cover, when I checked the oil, it was just off the full mark. The truck was parked on a slight angle with the driver side being about a foot higher than the passenger side.
2003 F350 w/6.0, 180,000 miles
I have a little problem with my 1999 f250 7.3 power stroke diesel. Every once in awhile, while driving the truck would die completely but i switch it into neutral and started right up. What could be the problem?
View 9 RepliesAbout 10 days ago following a heavy rain, I went to start my truck. It made a series of clicks and chirps, and acted like there was no power. Like dead battery or something. After fiddling get with the key and trying to figure the issues, all the sudden started normal door chimes....and truck started...no issues after that for several days.
Had another rain storm...same issues only this time took longer to get it to act normal. Once it did....no problems till today. This time wasn't a big rain...still acting weird. Battery's have power. ..it's not a battery or alternator issue I'm sure. Seems like a grounding issue if I had to guess....but can not tell where...or if that's really it.? No codes or lights once it acts normal.
'99 F-250 7.3 PS 2WD Automatic 246,000 miles
Jumped in my truck a bit ago and it wouldn't start, although it is turning over. The "Wait to Start" light is not coming on and the Overdrive button on the shifter is lit up OFF and won't change with me pressing the button. I've checked all the fuses under hood and inside cab with multimeter and everything checks out ok.
Also, when it was raining last week I found that when I turned on my windshield wipers the truck would die. My solution to get home was to just flip it back & forth real quick every so often so I could see out the windshield.
'99 F-250 7.3 PS 2WD Automatic 246,000 miles
Jumped in my truck a bit ago and it wouldn't start, although it is turning over. The "Wait to Start" light is not coming on and the Overdrive button on the shifter is lit up OFF and won't change with me pressing the button. I've checked all the fuses under hood and inside cab with multimeter and everything checks out ok.
Also, when it was raining last week I found that when I turned on my windshield wipers the truck would die. My solution to get home was to just flip it back & forth real quick every so often so I could see out the windshield.
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil. I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. If you need any info off the scangauge let me know and I will post the exact readings. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
View 6 RepliesI have a 2003 7.3. Suddenly a week ago when I left work, I noticed my truck wasn't picking up much, but i was in a 40mph zone. I then jumped on the freeway and noticed the truck would not go over 60mph. Once I exited and got on another road with a 55mph speed limit, the truck would not go over 45mph, I had the pedal pressed all the way down and would not go over 2000 rpms. Also, for the transmission to shift, I would have to let off the accelerator.
View 1 RepliesI have a e99 f350 7.3 all stock. I have no power. The truck will crank for about 15-20sec before it'll turn over. I just purchased the*AE*but am fairly new to understanding it all. In idle its a little rough and when I drive I can only stay in the neighborhood because of fear of getting rearended due to very slow acceleration. Whats weird is that when i have no power while i am driving ill keep the pedal down throw it in nuetral and my rpms and*icp*pressure jump up right away. Things I've replaced:
Icp*sensor
Fuel pump
Pcm
Tps
Cps
Ipr
Dropped tanked and cleaned screens
When cranking my*icp*pressure climbs slowly to right under 500. I dont know what else to do ive been working on this truck dor two months some days 13hs straight, I am feeling defeated. Codes p1249 1211 1209....