I recently purchased a used 2001 E350 with a 7.3L and the transmission is not shifting properly. It will go into Reverse no problem, put it in "D" and it starts in high gear and will not shift out. If I manually shift from 1 to 2 to "D" it works fine and will even go into OD. It will not down shift on its own either. What should I do to fix this issue?
View 2 RepliesI have a 2001 E-350 with 7.3 that will not start on its own. It is showing only 80psi ICP while cranking. It started with the aid of some starting fluid it will run at 550 psi ICP but the ICP duty cycle is running over 20%. We started with less than 10 psi while cranking and after a new IPR was installed it's now at 80 psi while cranking. There is good battery voltage oil is at correct level the HPOP is full. I just don't know what to look at next.
View 6 RepliesI have a 2001 E-350 w/7.3. When I start the truck first thing or when engine is cooled down it starts fine. I checked the high pressure pump pressure and it is 500 - 600 psi start up great. But when engine warms and try to start it it has long crank before starting. I checked pressure and it is between 425 to0 450 and takes awhile for it to get to 500 or better. Is this a cause of the high pressure oil pump ? I changed the oil and still does same thing. Also I noticed that after engine is hot and I try to start it, while cranking the engine the oil gauge does not move. I don't know if it supposed to when you crank it or not. I thought on other 7.3's I've worked on that the gauge builds up pressure....
View 14 RepliesIn my 2011 F-250, 6.7, auto....it seems that at certain times went the tranny shifts from 2nd to 3rd and I pause with acceleration, for some reason the tranny seems to go into a slip mode and then slams into 3rd. Now I read about 8 months ago that there was a computer upgrade via Ford. Which they did when I was having some work done on the truck at the dealership.
View 14 RepliesAnyway I have a 2001 F250 7.3l 4X4 supercrew 8 foot bed. Have an upgraded turbo, 4" exhaust from turbo back, k&n cold intake. Has 207,000 miles on it, 198k from first owner, the rest from me. Anyway the transmission is a automatic R4100 tranny. Since I have owned it it would shift from 3rd to 4th on slight grade. It would continue to shift up and down till I got back on flat again, rpm's would not vary to much depending on the grade. So that problem continues and now today I was towing a 14' trailer with 3 wheelers on it and I smelled smoke. Pulled over and it was pouring oil from the bellhousing. I had no choice but to drive back home about 20 miles. I first stopped and poured 2qts of ATF fluid in and then babied her home. What are my options here, what I should be looking for to fix?
View 1 RepliesVehicle: '99 E350, V10
Symptoms: speedometer bouncing, O/D flashing, harsh shifts. Symptoms do not present until the van has been driven at highway speeds for about 20 miles. Then, the speedometer starts to bounce a little. Then, after another 5 - 10 miles, the O/D light starts to flash. Then, with a few more miles, the harsh shifting begins.
Parts replaced: neutral safety switch, rear ABS/speed sensor (twice), instrument cluster.
Each time after I replaced a part, when I drove the van, all was fine until it had been driven at highway speeds for about 20 - 25 miles, regardless of whether the engine was warm or cold. Where to go next with it?
I put a ts6 on my 2001 7.3. I love it shift points are better and truck has a lot more power. But I've noticed when I shift truck shifts into 3 (especially going uphill) I get a really weird turbo sound where it acts like its gasping for air (I have 6637 air filter) and then it shifts kinda rough into third. If I put chip on stock setting it doesn't do either of the things I described. Do I have loose turbo boots somewhere or possible bad turbo bearings?
View 4 RepliesI am still failing to appropriately diagnose the problem(s) with my '03 Ford E-350 7.3L Powerstroke. This van has only 69,000 miles on it. A week or two back (just a few days back in work time) it suddenly went from running perfectly smooth, clean and wonderful to this:
- Zero power. Putting the van in gear and flooring the engine causes lots more smoke not nearly any rev of the engine and just a crawl forward.
- Lots of smoke out the back exhaust, whitish. I cannot discern wether it smells like diesel or oil (because I'm ignorant here), but the smell is very strong.
- After warming up and idling ~ 15 min I check under the coolant cap and see no signs of bubbling or disruption (from opening the cap in the coolant tank).
- After warming up there are no warning lights visible on the dash, and I don't have a computer to read codes (if there are any to read).
- I replaced the turbo up-pipes which had a visible leak previously. This did not hurt the symptoms, though no more visual leaks under the dog house.
- I thought maybe I put gasoline instead of diesel in the truck, not so.
- To do the above test I had to use the fuel pump to get gas out the tank to test. I hijacked the fuel pump output and turned the car on a few times to get gas out to a tank. The pump seemed to work just fine.
This was all very sudden which is perplexing, and, in use, the van was previously an ambulette and in my few miles with it (maybe 200-300 only) use was extremely light for such an engine/van, just driving around doing errands. I am not sure if this is relevant (no one has suggested so, yet) but before all this happened I uninstalled the rear HVAC that came with the van when I bought it. The AC lines were sealed under the hood. The coolant line was returned at the doghouse (you can see this at the beginning of the video).
At the moment the van has no power to go anywhere. I have not yet checked the CPS or IPC sensors, and understand this might be the next route in standard troubleshooting?
2003 Ford E 350 7.3L Trouble - YouTube....
My 99 E350 with 7.3 power stroke quickly lost power while on the highway today, bogged down and died. I couldn't get it restarted so had to have it towed home. I tried getting it started at home but it just pumps out white smoke out the exhaust. I got it to fire and run for a minute on a mixture of starting fluid and wd40 but wont stay running. Some background info, I checked oil and it was low but still registered at very tip of dipstick so I topped off oil level and still no start unless I give it a mixture of starting fluid and wd40. Batteries are good and cranking fast. Truck has 355,000 miles but very little blow by and prior to this had plenty of power and didn't have to use the block heater to start it thru the winter even when the temps dropped down to 12 degrees in January.
One thing I did have an issue with this past year was an intermittent cutting out while driving where the engine would instantly shut off but as soon as I tapped accelerator pedal it would start running again like nothing happened, wouldn't even last two seconds and it was running again just like shutting off the key and turning it back on and when it would do that the "Wait to start" light would come on and gauges would drop like key was off but again it all went back normal as soon as I hit a bump or tapped the accelerator pedal and it never lasted more than a second or two and never had to pull over, just tap the pedal or hit a bump and engine would kick in and run fine so not sure if that's related to whats going on now or not.
I have a 1999 Ford e350 7.3 powerstroke with 140000KMs on it.
The truck cranks really well but it just wont fire off, not even with a shot of starting fluid.
I recently changed all 8 glow plugs, fuel filter, fuel, oil and I keep it plugged in, my last mechanic told me the engine is toast and it cant be fixed.
I have a 99 Ford e350 7.3 Powerstroke with about 150000KMS on the clock. However I am having a really hard time starting it in the Cold Canadian Winter (-30). Last week I changed all 8 glowplugs, the batteries, the oil, fuel, fuel filter and yes i always keep it plugged in.
It cranks really well, but it just wont fire not even with a shot of start fluid. I don't know anything about these trucks much less a diesel engine. A guy took a look at it and said my engine needs to b replaced. (I think he is wrong)....
One of my batteries on my van is on the frame rail. The box rusted out so I routed the battery into the back of the van for now. The van wouldn't start because the batteries were low. I charged the battery in the front engine bay overnight but it did not charge the 2nd battery, does that mean there's a disconnect between the two batteries? I thought they were in parallel.
View 2 Replies2002 e350 7.3 diesel transmission... At 7 miles the speedo began bouncing and truck drops into second. Parked it 30 minutes, stated up no problem until 8 miles and the it started again. Have checked most of the electrical, changed speed sensor and transmission position sensor. Only error code 2-3 rd gear mismatch.
View 11 RepliesSo a dead thermostat forced me to drain the coolant in my E350 7.3L. I noticed the previous owner had green coolant in the van so I decided to do a flush and put in the right coolant. I used Shell Rotella ELC. Well, I noticed after coming home the other day that the van was leaking coolant, upon inspection I noticed its now leaking from the water pump, then today the drain valve sprang a leak! What the HECK is going on!? Is it possible that the seals were shocked when I changed the coolant? Not looking forward to doing a water pump replacement on an E350... sure is crammed under the hood.
View 9 RepliesI have a 2000 Ford E350 Short Bus 7.3 It has abs in the rear diff. I have changed the sensor. I have connected my AE but get nothing at all from the sensor. My speedometer does work. My overdrive light flashes and the transmission does shift properly. I plan on looking for a bad ground. Can I test the wiring using a volt meter
View 2 RepliesI have a 2001 F350 4x4. My transmission went out a while back. It would only go in reverse. I had it rebuilt and it is still having issues. When I take off with speed from a dead stop it shifts late...about 3000 RPMs. It shifts fine until it shifts into overdrive. It will go into to 4th then right into overdrive causing the truck to act sluggish.
I'm looking into my truck not starting well at any temp too! I didn't know if it could all be connected some how. My mechanic said that when he first started my truck it had a MAP sensor code. He also said that when he unplugged that sensor it didn't change the way the truck ran..Still like crap. I have changed all glow plugs relays and even did the mod to it.
I am currently converting a 1999 E350 7.3 diesel bus into a camper to live in. The bus has already had a lot of weird custom work. Done by someone else and a lot of the interior torn out and extra insulation put in. There is an exposed electrical panel behind the drivers seat. It was a cheap buy, previously fleet maintained with only 120k.
I was hooking up a battery for accessories to a terminal labeled "Battery" that does run indeed directly to the + terminal of the battery in the engine compartment.
Unfortunately I mistakenly connected the accessory battery to a terminal labeled "ignition" that runs to behind the dash. When I tried starting the vehicle off the auxiliary battery for a test everything went out for 2 seconds, I heard a click from the engine compartment, and everything than came back on. This is when I realized my mistake.
It used to be the speedo only didn't work (which I assumed was the step motor), now after this mistake all the gauges, the odometer and the buzzers don't work. Lights like the battery and airbag warning indicator still function.
Checked fuse 2 (15 amp) for the instrument cluster and it is intact. Actually checked every fuse in the vehicle in both fuse panels and all are intact. The radio works though and the vehicle is not equipped with power windows.
Going to go get a radio removal tool to take apart the dash and get back there. What this could be? Did I fry a relay? Did I fry the cluster circuit board.
Here is my issue. I have a 2000 e350 7.3 the overdrive light is flashing, the speedometer and the odometer isnt working it also shifts hard, i changed the vss, the vss plug, range sensor, and alternator. still acting up. also all the fuses are good.
View 8 Repliesmy parents have a f350 which now has no reverse. it has a reman sticker on it, 230k on the truck but no idea on mileage on the tranny. shifts 1st through 4th fine, no slip. Tc lockup works just fine. No codes found with my solus scanner. When shifted in reverse it will move back about 2 ft if revved above 2k and then nothing. Am I looking a trans rebuild or is there something I can check and repair with in it the truck?
View 4 RepliesI have an 02 F350 7.3 ... I just installed my glowshift tripple gauge pillar set. I have an EGT, Boost and fuel pressure gauge ... I followed all the constructions on installing them. The boost is working just fine and the EGT was too, but after a while the needle started going back and forth and the red warning light what blinking and then it just sat at 0 with the warning light on and stay that way. My fuel pressure gauge is connected to a sensore i put in my fuel filter housing, my fuel pressure gayge right from the start stayed at 30 psi with the red warning light on and just stays there .... Also the buttons to change the color and set the peak on the EGT gauge are sticking for some reason and staying down and aren't letting me change the color ...
View 12 RepliesThe car on cruise control sometimes randomly looses speed & downshifts to 3 and raise rpms quickly to gain the set cruise control speed again."
Vehicle Background: bought it from the original owner, the fuel gauge showed empty on a full tank of gas and I passed on the car, owner called a week later and said they installed a used PCM and everything now works, and it did, I bought it since it was a really clean car.
After driving on highway with cruise control set it would randomly loose power and downshift and then regain speed from being set on cruise control, mostly uphills and downhills but also straights sometimes and it would loose 7-8 mphs not the 1-3 mph loss that is typical of some other cars on cruise.
Engine has been rebuilt to success, other then this issue, the car drives like a dream and doesn't burn a drop of oil. Plenty of power compared to before the rebuild as well.
I learned from a DIY oil consumption fix on a 98 corolla that removing throttle body and cleaning it and the IACV, makes the vehicle idle within stock spec, really quiet and also improves the throttle response, I attempt this on the GT-S.
So I open up the airbox to make room to clean my throttle body and the 2 nuts were fairly loose, but the 2 bottom bolts were completely out that attach the throttle body to the intake manifold and only holding their place because of the tight fit in that area from all the hoses. This wasn't even touched during the engine rebuild.
I remove everything, looks dirty as [censored] and the intake has some oil in it, which I use brake parts cleaner to dry and use air to blow off and only got to remove maybe 30% of it from the inside of the intake. I then also remove the IACV to find it REALLY dirty like all the ones I had open so far and I go to town and cleaner both that and throttle body and replace both the gaskets as well.
Upon completion the vehicle's throttle response becomes AMAZING compared to before and it seem like a proper GT-S rather then a slow car which before had a slower acceleration then my 01 GT. I drive the same route home of 25 miles, the car NEVER once down shifts and has plenty of power and I'm HAPPY!
Well guess what, the issue is back now, I open the air box and both the nuts and the bolts seems firmly tight. I loosen everything up to still see the oil in the intake(though I only got to remove/dry30% the first time), brand new OEM PCV valve in the car 5k ago and I followed the PCV Valve pipe to the intake and it was dry from the inside as well.
when the vehicle is driven around and it returns to idle, it seems to hesitate(I think not 100% since it could be the engine just slowing down didn't do it before the throttle body cleaning though) for less then a second when going back to idle speed, it idles perfectly at around 750 rpms though. Questions:
1. What could be causing the oil in the intake? is it just the old oil what has been in the intake since before I bought it? The car doesn't burn any oil in the last 5k since the engine rebuild.
2. Could it be the PCM/VCM is causing the random power loss with cruise control on? which was a problem that was so called fixed using used parts but all the other automatic functions work perfectly.
3. Could it be the Cruise Control it self, apparently I can snag one from a local pick n pull for like 8 bucks (I think, listed on website)
4. Could it be this issue listed in this link? [URL] ..... , bad throttle position sensor? could it be that I cleaned the idle air control valve too roughly to get that slight hesitation when returning to idle?
5. Could it be the Throttle body itself in the GT-S? Did I clean it too aggressively, and ruined the round opening, which is causing the random loss of power? I had my cuzin do the throttle body removal and cleaning DIY step by step on our 99 corolla and he used a gasket remover (attached to a power tool) to clean up the dirt/oil build up inside the round opening and it started to give him jerks driving at highway speeds, constantly...We used the 98 corolla's gently cleaned throttle body in the 99 corolla and immediately issue solved. The proper working throttle body in the 98 corolla is a used replacement one as I aggressively cleaned the round opening in the original one and had hesitation issues as well.