How can I eliminate the factory Ford (2001 7.3) quick connect fuel line clamp on the output side on my OEM fuel pump? Do I just cut off the factory quick connect and add some 5/15 fuel line? Is it that simple or is there something I need to know prior to cutting off the factory quick connect clamps?
View 6 RepliesMy dumb self cut my factory harness to install a radio and after hooking up said radio (which I know how to do) it popped a fuse. So to avoid any trouble I need to put another harness in but again with my stupidity I cut the wires too short. finding the correct harness
View 2 RepliesI'm trying to replace my transmission output shaft seal on my 2wd and I can't seem to get the seal removed. I couldn't find anything to rent from O'rielly's or Advance Autoparts that would work. It's in there really tight ....
View 10 RepliesI recently started noticing that when I am coming to a stop(usually a quick stop), the trucks rpms drop to low. hard to tell how low but looks like around 450-500 rpms. I can feel the truck struggle just for a second then the rpms bounce back to 650-700. i was sitting in my truck while in park and was revving up to about 1200 and then let off the pedal and it died. My positive battery terminals are getting pretty bad and am going to replace them soon(waiting on parts). Could this be the cause?
View 14 Repliesmy 2002 7.3 with 370k just started to puff a small cloud of white smoke on start up. i realize this is normal during cold months but it is currently 102* in Texas. it will do it on the first start up of the day or if i start it immediately after shutting it off at full operating temps and when i do get a smell of the white cloud it has a oil smell but this only lasts while the cloud is dispersing all of that only lasts about 2-3 seconds no loss of power good boost pressure when driving no rough idle at all nothing acting any different other than the cloud and the quick smell of oil...
View 14 Replies2003 Excursion 7.3
There is fuel leaking from somewhere on the passenger side of the engine.
What things should I be looking for? I'm thinking injector? Is it easy to identify and replace?
I have a 2001 f250 7.3. Recently started this problem idling at 1000 Rpms when stopped completely and when I let off the gas pedal it idles real funny like it's fixing to run out of fuel. It does not do this all the time however. At times it runs great. I had my mechanic scan it and at first it was the exhaust pressure sensor. Replaced it and it ran fine for awhile and it started doing again. Took it back in to get re scanned and it was throwing a bad ICM code. Replaced this as well and I'm still having the same problem. Had it scanned again and it's not throwing any codes now. I have no check engine light on and as long as I'm on the gas pedal it runs great. It's just when I roll up to stop or when I'm stopped completely. Again it does not do it all the time.
View 9 RepliesI have a 2001 f250 7.3l 4x4 and the fuel filter housing is leaking real bad from either the back or under it. I need to get info on parts that i would need as well.
[URL]....
I've had an engine oil leak for some time. Recently I've had to add about a quart a month. I got some fluorescent dye and added it to the engine oil last time I added a quart. Ran the engine for a few weeks. Then cleaned the engine valley with cleaner and hot water.
Tonight I investigated the top of the engine with a black light. To my surprise, the oil leak is coming from the fuel bowl, right around the drain valve. I can clearly see about a drop every 3 seconds of fluorescent yellow liquid falling into the valley below and yellow all around the valve.
I expected a leak from the HPOP not the fuel bowl. Do I have a bigger problem? Is engine oil getting into the fuel? I plan to replace the seals in the fuel bowl, but not until I know whether I have a larger problem to address.
2001 F250 Crewcab, 220,000 miles
My7.3 is idling rough till I pull the fuse for the fuel pump them it will smoothen out I ran a by pass switch to us my truck but the fuel mileage is bad why
View 13 RepliesI am currently doing my injectors. Just a quick question. I was trying to get the fuel rail drain plug out but it stripped, actually not on the driver side stripped. I know there is the drain plug on the back of the cylinder. If I drain that and turn the crank over by hand will that drain all the oil and fuel that has drained into the cylinder? I'm really not trying to bend a rod when I turn this thing over. It's A 2001 7.3
View 5 RepliesI have a 95 f-250 psd with factory remote keyless entry. about 3 weeks ago i had a fuse blow that powers the keyless entry module, speed control, and a number of other systems.
If I replaced the fuse it blew right away so i got my wiring diagrams out and started unplugging parts of the circuit and my last attempt was to unplug the keyless entry module. presto no blown fuse so i got a module from a junk yard fixed the problem and now it has happened again. same exact thing. unhook the module and no blown fuse. i took the first module apart and saw no burned parts and no visible damage but here i am blowing fuses with no door locks, dome light and a few other things.
The fuse that blows is fuse 8. I am a mechanic and have full access to anything I need. I have another module under warantee but I want to be sure that its not something other than the module causing problems.
I have a very small fuel leak in my 2001 F-250. I was going to just let it go until I needed to do other work (since I get 20mpg city and 25mpg highway), but I went to a "new" inspection guy, and he flunked me. So now I have to fix it. And for all I know, my mpg and fifteen other things will break when I try to fix this.
Today I spent 4 hours in the heat putting in two new o-rings on the water separator valve. But the truck still leaks fuel. Climbed up on top of motor while it was running and looked, but I don't see where the fuel is leaking out.
Online research suggests to me that the next most-likely culprit is a steel fuel line that wears through from vibration and chafing. Is that correct?
This truck is so eaten up with rust (came from salt belt) that I bought a LOT of fuel line stuff a year or so ago, so that when things started falling apart from rust, I would have the parts on hand.
Now I'm wondering whether I already have the part I'm likely to need.
So far, I have bought:
1. Dorman Fuel Supply and Return Lines
2. Riff Raff Diesel High Pressure Crossover (HPx)
3. Riff Raff Diesel Fuel Rail Crossover (FRx)
So my question is, am I likely to have something to replace the part that commonly leaks on these trucks due to vibration/wear/chafing ... or will I still need to buy another part?
I'm thinking that one of the two lines in item #1 above is the problem child...
I've got a late 99 7.3 truck that I just recently did a lot of work on. I installed a new turbo with bellowed up pipes and a new exhaust system and when I went to start it up it started leaking fuel in the back pretty badly. Initially I thought it was the banjo bolt or the passenger fuel line but looking at it more closely I realized that it's not coming from there. It's dripping all over the side of the starter and is collecting at the low point of the metal lines down below. I also saw small droplets coming out of the up pipe where it meets the manifold but it looked like nowhere near enough to produce the kind of leak I'm seeing, also I know fuel shouldn't be coming out of the up pipe to begin with. This is really annoying and I would like to drive my truck again.
View 14 RepliesSo I changed my fuel filters the other day.
All was tight and no leaks. Even ran the motor the customary few minutes and then went on an errand to lowes. So drove it a few miles. All good.
So just outside of town about 10 miles, third gear, up hill plenty of boost the inlet line on the filter let loose.
Sorta looked like I was driving on wet roads except I had all this smoke coming from the hood of the truck.
Pull over quickly so didn't loose much. That darn yellow quick connect had somehow worked itself loose.
Simple reconnect, check three times, wipe as much stuff up as I could and on my way again.
Not fun when trailer is in tow. So I suppose I lost a quart or two at most but enough to do some undercoating anyway.
Check those connections often.
So my 7.3 started sputtering and lost power, died on the side of the road. I wasn't far from home put about 8 gallon of diesel in the tank with a couple of fuel jugs and it fired right up.
Gauge was reading 1/8 of a tank and low fuel light did not come on. (low fuel light comes on when you start) Gauge came up to about 1/2 after putting fuel in.
What happened? Gauge was always reliable and low fuel light always did work. Only work done to fuel system was had new tank straps put on a couple of months ago.
01 7.3. Cranks, won't start. Tank was at 1/4 but is full now. The lift pump runs, I can feel and hear that the motor is spinning when I cycle the key. I removed the fuel filter and cycled the key and get no fuel into the bowl. It looks like the lines are stainless from the pump to the tank so I doubt it is sucking air. I pressurized the tank with a shop vac and I get fuel coming into the filter housing. Am I missing something obvious? I have never seen an electric pump that would run and not pump fuel. I removed the suction line at the pump and don't feel any suction there.
View 14 Repliesi i am having trouble getting the quick connect on the slave cylinder to go back in i just pulled the entire transmission and replaced the clutch and now when i try to put the quick connect fitting in the slave it is rock solid and will not go in at all
View 1 Replies2003 F-350 - 7.3. With the key in the on position there is zero voltage to the fuel pump. Fuel pump fuse is good. I traced the red with black tracer wire from the pump up through the firewall and to the safety inertia switch. The switch has continuity so it's OK. Then from the safety switch I traced the green with yellow tracer wire to a fuse block plug connector. Then I checked continuity from that connector out to the #40 fuel pump fuse and it's open.
So I then i checked from the fuel pump fuse to all the back connections on the back of the fuse block and there was no continuity to any of them. So I removed the back cover off the fuse block to expose any issues. I found two board mounted relays. Now, from the fuse I get continuity to one of the relay connections. So did Ford hide the fuel pump relay and make it non replaceable? Also if this is the pump relay then what circuit energizes it? I need to make sure before I replace the fuse block.
I have a 2003 F250 and dont have power at fuel pump, or fuse #30. I put power directly to fuel pump and it worked and truck fired right up.
View 13 RepliesCan I swap my seat bottoms? I have '99 F350 with 40-20-40 seats. Drivers seat is getting tired. Would like to take just the seat bottom and flip-flop. Can it be done?
View 3 Replies