Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - 4x4 Not Working
Jan 11, 2017
I have a 01 f-250 7.3 6 speed. I bought the truck a few days ago and the 4x4 wasn't working the dealer replaced the transfer case motor. I have another 01 f-250 that i have been switching parts out of to see if that makes a differences and found nothing to work. Ive switched the switch on the dash out and nothing. Ive switched the two relays under the hood and nothing. I have also checked all fuses. and the connectors on the transfer case.
So I finally popped the covers off the two relays and squeezed them with my fingers and boom transfer case locked into 4lo and then i can squeezed the other and boom back in 2h! So now I'm lost, I know the wiring from the relays to the transfer case is good and the switch is good and relays are good so I'm at a loss.. Also cruise control isn't working idk if that could be related i don't think it is but idk?
View 8 Replies
Advertisement
I have a 2015 F-250 with the bare essentials. It's built like a work truck but we use it as our everyday vehicle traveling around in Detroit.
That being said, there's a draft down by our legs that we've noticed for some time, but now it's really something I feel could use addressing because it just leaks in cold quite a bit. The draft feels like it's coming in from the front engine compartment/dashboard area.
Is what I'm experiencing common with this kind of truck and is there a fix, or way to stop that draft coming in? I feel this was just one of those things that wasn't really given much consideration as a work truck, similar to the fact there's no cabin air filter, but I'd really like to know if there's a way to somehow reduce the amount of air into the cabin compartment.
View 14 Replies
I have 2002 F250 7.3 Auto, I recently tried to put my truck in to 4 wheel drive and it is not working. It has WARN manual locking hubs, which I locked. Dash indicator came on and I can hear it click on the transfer case. Yet it isn't driving the front tires. It shouldn't be a vacuum issue considering it had been converted to manual hubs should it?
View 5 Replies
I installed a new trailer wiring harness onto the back of my 2002 F250 Super Duty with 7.3 diesel engine. Unfortunately, I was 180 degrees off on my wiring. When I hooked up to the camper I blew Fuse #115 (Trailer Tow Battery Charge) as it connected directly to the camper ground wire. I replaced the 20amp fuse and all other fuses were good. Currently, I have all the truck wires to the harness isolated and have power to all of them except for the parking lights. All the lights on the truck work fine.
My truck has a interior fuse panel on the driver's side as well as two small black boxes under the hood, near the brake booster. The under-hood boxes had only relays in them. Two relays in one black box, three in the other. The box with three relays had trailer left turn and right turn relays. which worked fine. The third in that box, apparently, is for the A/C clutch, controlled by fuse #10. The other black box (with two relays), apparently, are for 4WD Shift on the fly, controlled by fuse #111. So, no relay for the parking lights.
Next, I pulled the fuse panel out a little and checked continuity from the end of the parking light wire (brown with white stripe) at the back of the truck to the back of the fuse box and found that it was a good wire with no breaks or shorts to ground, however no voltage is showing at the parking light wire when I turn on the parking lights. The harness at the back of the fuse box has several wires going into it. The parking light wire (brown with white stripe) is in the same harness as the back-up light wire (black with green stripe) and the back-up light does have voltage, when I put it in reverse.
I'm not sure what happens inside of the fuse box, i.e., how does one fuse run a few wires... is there some kind of circuit board? I know the easy way would be to run a vampire connector from the truck parking lights, or maybe the license plate light to power the trailer lights, however, I'm just not built that way.
View 5 Replies
The fan clutch will come in and out rapidly when NOT in OD and pulling hills with the fifth-wheel attached. Replaced with a new aftermarket fan, then a new OE one. Then had the radiator pulled and all the bugs, etc. blown out. The condition has not changed at all. The original fan clutch was pretty sloppy. There are no codes, the trans fluid is nicely red, the engine does not overheat or even change temp when pulling hills. No check engine light ever. The truck is a 2001 F250 4 X 4 automatic extra cab with 7.3 engine without any modifications and runs perfect except for this. There are about 95k miles on odo. When we use overdrive on the flats, there is no issue.
View 12 Replies
I have 2001 7.3 f250 ... I just got it about 2 months ago I drove it for maybe 2 week and it ran good the other morning I went out to start it and would not start and the way I was parked my low fuel light was on so I put 5 gallons of fuel in finally got it started sum how drove it for maybe 2 hrs parked it and wen we got back in to go it was done for hasn't started since its been down for a bout 2 weeks now I've replaced hpop, icp, pcm, fuel filter,checked idm for corrosion it all looks well, gpr,checked uvch on driver side looked good and changed cps what else do I have to go from ? No matter what it won't start good batteries cranks good but no start ...
View 14 Replies
01 f250. Just bought from my brother. 140000 miles. Immaculate. Truck will die for no reason. Running down the highway, or sitting at a red light. Fires back up. Sometimes have to crank a few times. He has had at a mechanic and everything checks out good. Since birth its only had royal purple that he has changed every 5000 miles as well as all filters. Where do I start?
View 6 Replies
2001 f250 7.3 with 210,000 miles. Was running rough when cold and glow plugs were bad so I bought new glow plugs and had injectors rebuilt with 100% over stock nozzles. When I changed them I made sure I turned the motor with glow plugs out and pulled the drain plug in the head. Wanted to start it just to get the oil out before I let it sit for a few days til I got the tuner. It started fine and I let it run while I ran in the house and when I came back out about 1 min later it was off. Didn't want to start again. Just left it til I got the tuner on and It still doesn't want to start. What I should check? Turns over good and has good batteries. Also it's a hydra chip tuner with beans tunes. Darren weeks rebuilt the injectors.
View 7 Replies
So I have a 2001 f250 7.3l and on my way to work yesterday while driving down a hill I switched my ts 6 switch to 140 and it immediately stalled, so I pulled over and restarted the truck and it started up fine and I drove the rest of the way to work, I go to start it after work and it won't start, it just cranks and cranks and cranks, occasionally it'll fire and I got it to start and was able to rev it for about 30 seconds but then it died, disconnect the 6 position switch from the idm and tried but still nothing.
So today I replaced the ipr valve, got everything back together still won't start maybe a little worse now, I know it's getting fuel cause there's pressure in the bowl when I try to take it off, there's a new icp valve, cps, new fuel filter and new sending unit, the hpop is topped off. Also I noticed when I went to change the ipr the wires on the plug were bare and touching so I addressed that, I don't know what else it could be?
View 14 Replies
I have a 2001 f250 7.3 and I had started to notice I wasn't making as much boost I thought I should have been. I looked around and found a tear in the cold side CAC boot. My question is what is the best option for replacing it, something like RiffRaff or oem? Also should I look at replacing all the boots or just the two up top?
View 14 Replies
I have a 2003 F250 7.3 auto 4x4 SD ... has done 616000kms and is getting a bit rattily and injectors are getting tired . Have found a 2001 7.3 engine that has 130000 miles on clock . Will the 2001 engine fit into my truck .... e.g.. bell housing and crank bolt spacing's, mounts for all the bolt on bits ... is it quicker to take engine and box out or just engine ?? have even read on here that body removal is necessary .have a forklift and workshop available
View 2 Replies
2001 F250 7.3 - warn manual hubs.. However, the wife has been driving the truck and I don't know how often she has cycled 4WD.
Basically if you choose 4WD hi it doesn't light up to indicate that it has engaged, if you drive for a couple of minutes slowly then eventually it drops in - not much use if you're already stuck. It will then select 4Lo. Coming out of 4Lo to 4Hi or 2WD is painfully slow - like 5-6 minutes before the dash light goes out for 2WD.
I was thinking maybe the electric motor for the transfer case - unless it is the transfer case dying.
View 10 Replies
2001 F250 7.3 4x4 330000
So weird noise while breaking but only right at the very end of the breaking cycle or if breaking hard. As soon as you come of the breaks it stops. Changed out front rotors and pads last night thinking that was it but its not. I'm inclined to think it could be the driver rear side by having someone else drive and brake whilst stood by it - rear rotors and pads changed 18 months ago and quick visual check appears they are ok. Just can't work it out - any thoughts? Caliper seemed ok on the front left, but would probably need doing in the next 6 months
View 11 Replies
My 2001 f250 7.3 was running then just shut off like I had turned the key off, While trying to start back up, the truck turns over fine but no fire. I also have no gauges, I tested both fuse boxes and the one under the hood I have power on all big fuses, including the PCM but some of the small ones I don't, No power to the PCM diode, either side, the fuse box inside the cab, I have half power, No power to the PCM fuse is their a fusible link somewhere?
I really can't see much down there. The truck did get into a accident in Oct, which created a problem with the ignition and not sure if that could be a problem? That problem is, when I turn the vehicle off, it would stay running for a few seconds. I ignored the problem cause it didn't hinder the vehicle any.
View 4 Replies
Today my 01 f250 super duty has started making (5) beep tones (3) times in a row. I have my seatbelt buckled, all my gauges show ok. What is this tone indicating?
View 10 Replies
Just bought an 01 F250 7.3 but it will not move I think it has something to do with the fuses because it won't go in forward or reverse but I can't find an accurate diagram For fuse box I'm missing probably 8 fuses underneath the dash and I think one of them has to control the transmission module. What it could be if someone doesn't think the fuses...
View 9 Replies
Ok I've got an 01 F250 sd 7.3 with 257k on it it just started talking longer to start than it should it will do it cold or hot even if I shut it off at the drive thru takes it like 10 sec or more to fire. My question is I thought about purchasing a autoenginuity to find the problem but not sure the best place to get and what model I should get.
View 7 Replies
So I replaced all the rings on my injectors . After putting them back in turned the engine over 5-7 times by hand with the glow plugs out. Then I turned it over with them out as well with the valve covers off. After than I installed everything back in. Now is my problem. I've turned it over 5 times and no luck. Not even on turn over. The oil light keeps coming on?? The indicator doesn't move up at all. It will go up and come down ? Is something wrong with the hpop? Should I keep cranking? Gotta to charge the batteries now..
2001 f250 7.3
View 8 Replies
I have a 2001 f250 7.3. Recently started this problem idling at 1000 Rpms when stopped completely and when I let off the gas pedal it idles real funny like it's fixing to run out of fuel. It does not do this all the time however. At times it runs great. I had my mechanic scan it and at first it was the exhaust pressure sensor. Replaced it and it ran fine for awhile and it started doing again. Took it back in to get re scanned and it was throwing a bad ICM code. Replaced this as well and I'm still having the same problem. Had it scanned again and it's not throwing any codes now. I have no check engine light on and as long as I'm on the gas pedal it runs great. It's just when I roll up to stop or when I'm stopped completely. Again it does not do it all the time.
View 9 Replies
2001, F250, 4x4, 432,000 miles...
Seems this truck eats up bearing assemblies. Its like every 2-3 years, I'm having to replace one side or the other. And we talking like 30-40,000 miles....
BTW.... although I'm not out doing much 4x4 driving, this truck does do a lot of dirt roads, probably over 50%...
View 6 Replies
2001 F250 7.3L 280k... On a 50 ish degree day or if the truck is cool on a warmer day I'm getting an inconsistent idle lowest end 450rpm high end maybe 750. Wondering now what the possible causes may be, truck seems to run fine and idle ok once warmed up but still cycles the revs a little, AC is off.
Second question is about an oil leak, doesn't seem to be massive but it leaves a small pool, especially if she's plugged in. It seems to be coming from underneath the truck driver side large metal tube system running front to back on the engine, just under the manifold I think.
I checked HPOP connections and they are solid no leaking but here's a pic from under the truck, can't see any of this from the top. Is it an easy fix??
View 14 Replies
