Ford 7.3L Power Stroke (1999-2003) :: Code P0266 And P0281 - Injectors Cause Hard Start?


May 9, 2016

My 2002 F450 7.3 won't start unless the heater is plugged in for 2-3 hours+ regardless of the weather. Today I did a cylinder contribution test and at first cylinder 2 got code P0266 (Injector Circuit Contribution / Balance Fault) and cylinder 7 got code P0281 (Injector Circuit Contribution / Balance Fault). I drove it 10-15 miles and did another test. Only Cylinder 2 got code P0266. No error on cylinder 7. I've used RevX with some success before, so I'm tempted to try it again see if it clears up the error on 2. My question though can injectors be an explanation for my hard start situation? (I've already replaced EGR, ECP, Fuel Filter, CPS and glow plugs seem to be fine also).

View 11 Replies

Advertisement

Ford 7.3L Power Stroke (1999-2003) :: 2001 - Hard Start With White Smoke - Bad Injectors?

My 2001 7.3 was smoking excessively and I rebuilt the turbo and the center cartridge was at fault for that. I'm still having some of the problems I was having before with a lot of smoke at cold start (I have to hold the accelerator down while I start it and it takes about 10 seconds to start) even when I hold it I have to keep it held for about 5-10 seconds before the RPMs get to where they should be. And it smokes like crazy.

Then after about 3 minutes warming up, or 30 seconds of me holding it at 3500 rpm, the idle smooths out and it only smokes a little. Then once I start driving it doesn't smoke a lot unless I go hammer down then it puffs some white smoke. I took the oil cap off and it isn't huge amounts of blow by cap just rattles off. Can ford buzz test and see if I only have 1 or 2 bad injectors? Could this be anything other than injectors? It has a ts6 on it with 24xxxx miles with factory injectors.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: F250 Getting Hard To Start / Code P1670

But it starts. '99 F250 PS. Had code P1670, cleared it. No other codes. Started truck back up and ran KOER test with AE(which I'm not very good with). The code did not come back. It is hard to start plugged in cold or warmed up. I have WTS light and it goes out(glow plugs are original). RPMs are slow to come up (almost starts before it kicks in). Doesn't matter if fuel tank is full or not. Oil level is fine. Batteries are charged and check good. Starter checks out ok. Buzz test was ok. Now when I run KOER do I need to do anything other than hitting the initiate button?

View 10 Replies

Ford 7.3L Power Stroke (1999-2003) :: Won't Start - Bad Injectors - Coolant In The Oil?

So we begin w/ another saga for the 7.3l Excursion......

A few months ago it started running like crap, real crap and blowing white smoke like crazy. Well I knew this from a previous episode and I had a bad or multiple bad injectors. I tried to trouble shoot which one it was and maybe just replace the one or two....but no it was worse than that. So Life was really busy it kinda got shoved aside until now.

I pulled all the injectors and had them rebuilt locally ..nice. They ended up being with mech for a couple of weeks because he went out of town...no problem. Well this entire time my rig was untouched and when I got them back #7 was full of water.....great, bad injector cup. #7 was the only one, the rest were dry. So I drained the radiator and the oil and left it overnight to completely drain and installed the new injector cup in #7. Next day I refilled via both heads because the valve covers were off, 4 gallons of oil and a new oil filter. Cleared the cylinders via the glow plugs and commenced to trying to get her started. Nada......just cranks, killed the batteries, recharged over night and left the box on them and still nada....but the oil was still very milky at this point.

So tonight I pulled all the injectors back out and drained the oil again, still a lot of water. This time I sucked out the HPOP reservoir and got a more milky water/oil out and I'm leaving everything open all night.

In the am I plan to check my overflow water level in the hopes it remains at the same level...if so I will reinstall all 8 injectors and refill the motor w/ 4 gallons of fresh oil and try again.

Oh, while I was attempting get her started I put my buddies Snapon scan tool on it and I got the p1271-p1278 codes w/ the buzz test. (low side to high side open circuit between idm and injector) So I found the pin test with everything connected at the idm pigtail and everything tested good. So I'm back to my not so fresh oil anymore is the culprit to it not starting.

Am I missing something here?

Also....another fun filled fact is that I seem to have a fuel leak somewhere at the rear passenger side. Every time my fuel bowl fills up, if I shut the key off it will drain down. Sometimes I can see fuel dripping quite vigorously onto my starter but I can not see where it is coming from. I have while it was dripping ran my hand along the head and the fuel lines and can not find where it is coming from. Any thoughts as to where in the hell this fuel could be leaking from?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: New Injectors - Crank But Won't Start - Low ICP?

So I got all 8 injectors upgraded and excited when I get them back I put them all in in kind of a rush. And in that rush I left the cylinders full of excess oil. So obviously when I tried to start it hydro locked. Angry at myself. I kept trying to crank hoping it would fire and just shoot that oil out. Nope, so I went back to taking all the glow plugs out and firing it all back out. Put it all back together then tried to fire her up. Took a minute but she started and I let it run for a while. Hit the gas a few times and then it died. Couldn't get it started again. It would just crank, I checked the icp and ipr and the icp did not build above 35 psi and the ipr was at 98.04% so I just figured the o rings blew out when it hydro locked.

So I took it all back apart put new o rings on, took my time and put it back together right double checking everything. Got it all back together and went to start it, it would just crank around 160-170 rpms, battery voltage at 10.6 icp built up to 140 but now it won't build past 40. Ipr still goes to 98.04. The engine ran just fine prior to injector change, I put a new upgraded hpop prior to injector change, new ipr, icp, cps. Everything checks out, but it will not build oil pressure while crank I've killed a set of batteries then went all out and spent 350 at napa for some optima red tops. I did notice the cylinder 7 injector is the AE injector. It suppose to be in cylinder 8, idk if that's affect the oil pressure building up?

But as far as I know, I'm not building oil pressure. So idk if the hydro lock could have ruined something to keep it from building oil pressure?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: No Start After Cups Install And New Injectors

I just replaced my cups because of bad leak. well replaced all cups and injector from a rolled truck the truck ran when pulled. well installed went to start and have tried for 2 days on and off still not start did buzz test and passed , checked oil reserve and was full. When I first tried to start it acted like it was hydrolocked and then hit it again and been turning fine

YouTube ....

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: HPOP ORings Replaced - Injectors Loud After Start Up At Idle

Just replaced all hpop orings. Injectors loud after start up at idle. Guessing air in lines. How long do I need to drive before all air out of lines and everything back to normal?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Start Rough When Cold - Injectors Not Working On 165k Motor?

Replaced o-rings, injector cups, glow plugs and UVCH with all motorcraft parts 2 years ago and the ICP, IPR and resealed the HPOP last year. I use rotella 15W-40 oil. It has been hard to start when it is cold and runs rough with little power until warm for a few seasons now when it is cold outside. There are no fault codes or issues otherwise with the mostly stock truck. A buzz test when the engine is cold only #6 sounds strong and #8 isn't quite as bad as the others but the others are hardly audible.

Cause:

1) Can 6 to 7 injectors really go bad in 165k miles? If it is injectors I believe the Alliant look to be the way to go with type ADs?

2) Since it is like flipping a switch and the number of injectors effected is it possibly the 0.1% of the time it is the IDM when there is a miss and no SES. From my searching and swampdiesel if there is a miss and no SES it is 99.9% it is not the IDM or harness since it actively checks continuity.

View 13 Replies

Ford 6.0L Power Stroke Diesel :: 2003 - Hard Start - CEL On - Code P2285?

Truck has performed flawlessly during that time period. Early build 2003 CC SB 4wd King Ranch truck 94,000 miles I purchased new in 2003. Good batteries. Bone stock except for superchips tune.

First sign of trouble: Two weeks ago CEL came on, P2285 Injector Control Pressure Circuit Low, as soon as truck was started after sitting unused for about a month. Bought new sensor, haven't installed it yet (early model sensor located under turbo on rear of engine and a real pain to change). Truck still started fine and ran fine. Dreading the ICP sensor install, I continued to drive the truck. Drove truck 5 miles to get tractor fuel. Got fuel, started truck and drove away. Got 200ft and truck died. I changed secondary filter under hood, turned key on and let pump cycle about 4 times. Truck started. Cleared codes. No longer have CEL. Drove 5 miles home, shut truck off and no start.

Troubleshooting: Changed primary filter under truck. Really cruddy (probably 80,000 mi on it). I cleaned inside filter housing thoroughly. I had to cycle pump KOEO about 6 times before it started. Shut off and immediately tried to start. No start. Ran pump KOEO about 30 seconds. Started. Shut off and same result. I then drove truck 4 miles driving both normal and WOT. No problems, no smoke, no CEL, ran perfectly normal. Shut off, no start until cycling pump KOEO for about 30 seconds. No codes set.

I then removed cap from secondary filter and checked for trash. Fuel and bowl were clean. I did notice fuel drained completely from bowl in about 5 minutes. I reinstalled filter and put pressure gauge on housing.

Fuel pressure readings: KOEO 55psi after about 3 seconds. Engine running 55psi. Turn key off and pressure instantly drops to 25psi, then bleeds off to zero over about a 3 minute time period. Does this seem normal?

Questions: Could the clogged fuel filters cause the p2285 code to set? Could the HPOP system have developed a leak and cause these symptoms?
Could an injector leak cause these symptoms and engine still run ok?

Action Plan: Install new ICP sensor. Do bubble test to check for injector compression leak. Install Blue Spring mod. Waiting on parts. Possibly buy scanner which will read HPOP output etc. Any recommendations here?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Low On Power / Injectors HPOP Or Tune?

So I have a 2002 7.3 Excursion and I think it is low on power. ICP is falling on its face when on a 60 or 80 HP tune. I have some boost leaks at the plenums and will work on that but that shouldn't cause my ICP to tank at full throttle. Following are some numbers I pulled with WOT runs up a 6% grade.

16PSI BOOST
EXHAUST PRESSURE 40
ICP 1900
80%IPRDC
this is with the 60 or 80HP tune on my DP-tuner. If I ease into the throttle I get
2700 ICP with
45%IPRDC
but if I stomp on the throttle it stumbles and ICP tanks.
Running the stock tune I can maintain
2700ICP at
40-45%IPRDC

Is this my HPOP being weak, or worn out injectors, to much of a tune or a combo of all three?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Injectors Barely Spitting Oil

This is a 1999 with 200k on it. It has a really bad hpop so valley is full of oil. Haven't removed the HPOP to inspect the non serviceable plug or the hpop gasket. doing that this week. This truck I just bought and it has aftermarket injectors so dont know the miles in injectors. once the oil leak is resolved I can then give the injectors the once over to make sure theyre okay. Question is how much of a stream of oil should I expect to see as the engine runs?

View 11 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2005 - Putting New Injectors?

Are there more parts that i would have to get when putting in new injectors in my 2000 f250?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Oil Coming Out Of Spouts On The Injectors?

What causes oil coming out of the oil spouts on the injectors? I pulled my VC to re torque my injectors down and I noticed 2 of mine are now leaking oil out the spouts(when warming the engine). Note I did not say the base of the injector.

View 8 Replies

Ford 7.3L Power Stroke (1999-2003) :: Replacing Injectors - Which Injector Goes Where

I just bought a 99 F350 with 240k miles on it and got it for a deal because it needed injectors. Ive done the same job to my 97 OBS powerstroke. The injectors were already pulled so I had them sent for rebuild, the problem is I cant tell which injector goes where. is there a trick to figuring out where each injector goes when I put it back together?

View 4 Replies

Ford 7.3L Power Stroke (1999-2003) :: Brand New Injectors With Dings In Them?

I paid for brand new injectors and when i took them out today they all had dings and small gouges in the plates,is this normal?they are 180/100 cc

View 4 Replies

Ford 7.3L Power Stroke (1999-2003) :: Hard Start Getting Harder

My e99 f250 has been getting harder and harder to start over the last year.

I think one of my batteries is dying or dead but it still cranks fast while it does.

For instance when I tried starting today it seemed to crank just like normal but their was some relay clicking inside the cab that was abnormal.

My understanding is aside from cranking no power is required to start the motor? what if the dead battery is taking some cranking amps from the good battery preventing the computer from getting juice?

would the truck throw a code if it was a glow plug?

View 9 Replies

Ford 7.3L Power Stroke (1999-2003) :: Lots Of Clatter - How To Test Injectors

Have a pretty good running (I think), 2000 7.3 with 151K that has always been pretty noisy. Lots of clatter. I amjust wondering if there's an easy way to tell if I may have injector issues starting to come up.

View 8 Replies

Ford 7.3L Power Stroke (1999-2003) :: Changed Injectors / Cannot Even Get Engine To Crank?

I changed my injectors and glow plugs on passenger side. I tried to start the engine and it wont crank (turn over). I tried to turn over by hand by turning alternator bolt counter clockwise, turns a little bit and then get very difficult. Is this hydro lock? I stuck a suction tube down injector holes and made it to the piston not much oil came out, I think the truck was a little low on oil before I started the project. The starter wont turn the engine over. I even turned the engine over by hand many times before I put glow plugs in to evacuate the cylinders. I don't know what to do?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Additive In Coolant So Injectors Don't Rust?

Someone just told me I need to put additive in coolant so the injectors don't rust. I've never heard of this.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Hard Shifts - Truck Will Take Two Tries To Start?

The first has I replaced my tranny with a stock 4r100 tranny and torque that only has 75k on it. The guy was doing a 6-speed swap. After I had the tranny and torque converter and a new tranny cooler installed, the tranny shifts real hard. I think it may be from my DP Tuner. Even on my economy tune driving it very easy sometimes, it jolts into gear pretty good.

I was wondering if I could just get a shift kit to maybe correct that and if so if I would have to drop the tranny to install the shift kit. I saw a bully dog kit for like 75 bucks, however, I don't really have the money to have the truck in a shop and I would really like to not drop the tranny and not lose all my tranny fluid if possible (very expensive).

Also my other issue, the truck in warm or cold weather is very hard to start. Half of the time it takes two tries to start it. It will crank and crank and no go. Then the second try it fires right up. It has two new batteries, where do I start? Is it possible that the starter is just getting old or is it fuel or oil pressure related possibly?

View 2 Replies

Ford 7.3L Power Stroke (1999-2003) :: Hard To Start When Longer It Sits

2001 F 350 7.3 183,000 miles.. The problem is the longer it sits the harder it starts.. when it does start it runs VERY ruff!!! it takes 10 min or so to run on all cylinders.... This is my first diesel..

View 4 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved