I need to replace the cable on my gear shift indicator. Of course you can't just replace the cable. I have even looked on you tube and not found anything. I don't know if maybe I am using the wrong search terms or not.
View 2 RepliesMy shift indicator switch on the trans seized up, so a local trans shop replaced it for me. Now I get no low range when I select it. I understand it needs to see the truck in neutral to do this, is there a simple adjustment? The trans shop is a long way away.
View 2 RepliesI noticed my '99 started getting difficult to get in gear & shift, within a coupe of days the peddle was barely off the floor before it would engage. A day later it started 'creeping' if started while in gear. Replaced the master/slave cylinders with no change.
Is a clutch replacement the next step? Just thought I would ask before throwing money at it, since the only other times I've had clutch issues there was slipping or it just plain exploded.
i bought a f250, i rebuilt the 7.3 after installing it the transmission isn't shifting correctly. Reverse perfect, 1st and shifts to 2nd great. wont go into 3rd. i replaced the 2 sensors on the transmission, i replaces the sensor on the 3rd member. the speedometer works but not correctly, i can unplug the sensor on the front of transmission and it shifts into 3rd. but when i plug it back it doesn't. no codes. could it be the ecm?
View 10 RepliesProblems with my 2001 F250 4r100 transmission. Transmission will only shift to 2nd gear when throttle is feathered at @2500 rpm. All other gears shift perfectly. This problem is consistent.
View 10 RepliesI have an early 99 F250 4x4 7.3L..... 4R100....
Brief history, a while back on way home from work I let off of the accelerator and had a loud gear meshing like grinding noise, got back on the accelerator and went away, let off and back, so I quickly stopped and pulled over, went through the gears and reverse, everything seemed ok,??? went on my way, got home parked the truck and went about my evening. came out next day to leave and truck wouldn't move in reverse, forward but not reverse. long story short I was told that the snap ring internally probably came out, I have heard of this being a big issue with these, so I set up for it to be rebuilt, got it back and installed and still same issue, what the crap so I ended up having to pull it back out and amongst my own trouble shooting I found the simple issue and was the nylon riders on the 4hi/4low shifter fork were completely gone and allowing the planetary group to free float in and out of 4x4 neutral!!! NOW on to the issue at hand. so far only thing has been done is rebuilt and those fork riders replaced.
now I can move but 2-3 upshift under a load(more noticeable) has a delay going from 2nd to 3rd and under a load it hits hard. I talked to the guy that rebuilt it and he said that the rebuild kits don't always the right springs for the valve body and causes shift issues, so he talked me into the shift corrector kit which I researched and did see what he was saying, so had that done and still no better, still does it, however, it does shift into the gear softer but didn't fix the delay or the hitting hard when it did finally go into 3rd.
After being forced to drive it that way I have since determined that what it happening is it is coming out of 2nd with a second and half pause and then shifting into 3rd, the hard shift comes in to play because during the delay the torque convertor is locking up making it a direct drive like popping the clutch on a standard!!!
I just swapped out the sol pack and I heard from a youtube video that the bolt next to the 2-3 upshift valve on the valve body could be to tight and making a sticky valve, so I re-torqued all the bolts and nuts put all back together and test drive proved to be worse, I now have same issue in all upshifts. all hit hard now, I am at a loss and don't know where to go from here, I can only imaging the sol pack is causing this but I have yet put my org one back in to see... oh and I found two bolts on the accumulator stripped and found one non torqued bolt on the main valve body!!
I have a 4r100 on in a 99 7.3 4x4. The shifting problem I have appears to be intermittant. it seems loose after warm up especially at the 4th shift overdrive and passing gear. possibly due to low presures ? sometimes (lately more often than not) hunts back and forth between 4th and o.d when passing or hill climbing. Under normal driving it shifts somewhat firm with 4th being an exeption.I have changed my crank position sensor filters and fluids which had turned dark and improved slightly. When I pulled the pan and replaced the filter the pan was spotless. No residue or signs of plates or debris. There is about 100,000 miles on the tranny and 350,000 on the truck. Questions: Is there a tcm for this transmission and if so could it cause these problems? I'm considering a purchase of an unlocked 1705 superchip to change the shifting but unsure if this will work for my issues...
View 14 RepliesIn the last couple of days my battery light comes on after about 30 mins of steady driving. I have no starting issues as of late. Batteries have been tested under load and checked out okay. Alternator is a few months old. Other than the battery light coming on there no other
problems, yet. Is my alternator over charging? A couple of month ago my truck would shut off when I turned a/c or heater on in the mornings. My alternator was over charging. After I replaced it I had no more problems. Could any of this be related to the life time led bulbs that I'm using?
I have a buddy with a 1999 F250 W/7.3 TD. His property is accessed through a couple miles of hard terrain, so this may wind up being a loose ground or something that pulled loose.Anyway, the truck just all the sudden won't accelerate. It'll crank & idle all day long, but when you hit the gas.....nothing happens. I realize the diesel doesn't have an accelerator cable, as it is drive by wire. First thought was the APP sensor(accelerator), but most of the dash indicator, O/D, etc. lights are inop too.
View 5 RepliesAbout a year ago, my airbag indicator light threw a code 47. It did this for about two days, then it stopped. Fast forward to this weekend, and it started again. From what I can tell, it is the passenger side seat belt pretensioner. It could be a coincidence, but my daughter pulled the seat recline lever without anyone being in the seat, causing it to fly forward as if James Bond was ejecting someone through the windshield. The next time I started my truck, it was throwing the code. I tried to check to see if the plug was knocked loose during the ejection sequence. I thought the connector was under the passenger seat, but I don't see any wiring (the passenger seat is manual). My next guess was behind the glove box, but I'm not sure what I'm looking for.
My truck is a 2001 F250 4x4 Lariat.
I have been having an issue with my 4-5 gear shift under hard acceleration and know that a rebuild is due soon but I was wondering if any high performance kit available with all the clutches and friction discs needed to rebuild.
View 6 RepliesLooks like a pia but nothing too crazy.I don't have a pitman arm puller, but can borrow one.
View 14 RepliesMy truck is a 2007 F-350 DRW. I'm not sure when,because I don't use it much in Texas, but My Four Wheel Indicator lights on the dash quit working. I don't see them in the dash at startup either. I'm not sure if the four wheel drive is coming on at all. There is probably a way to check that without driving off into a mud bog, right? Anyway I have looked for blown fuses etc, no luck yet. (15amp#33 under dash and 30amp#3 under hood). These are according to my manual.
View 2 RepliesSeems like I have an issue every other week of driving my truck. Today I arrived at work and attempted to shift into park but it wouldn't go. I went to tighten the bolts and after tightening it still wouldn't work. So I tried tightening them again and the top of the top bolt broke off. So I took a nut and a lock washer and put it on the other side (was very hard) and got it tightened best I can. It looks tightened pretty good but I still can't shift into park. Maybe the bushing for that piece are bad? I have no clue where to go from here or what I need or even if putting a nut on the bolt works.
View 4 RepliesWon't shift into park, Checked the two bolts and they were tight. Ended up having a rock wedged behind shift lever on the transmission.
View 3 RepliesWe have a 2002 excursion. I have replaced the 4x4 selector switch on the dash as well as the front hubs they are now the warn premium hubs and the transfer case shift motor all part are ford all but the hubs. My question is it will not shift from 2 hi to 4 hi to 4 low, I have done all the right things that the book says to do, put vic in neutral keep foot on break, switch selector switch to 4x4 or 2 or low and it will not shift. When the transfer case shift motor was off i put the truck back in 2 wheel drive by hand with a wrench and it moves free no binding what else could it be the fuse under the steering wheel is good and new parts are good as well...
4x4 2002 excursion limited 7.3 only mod is cold air intake....
I'm in the middle of replacing the hub and bearing assembly, once i got the hub assembly off, I noticed when I grab the axle there is a lot of play if I pull the axle up and down or left to right. Is this normal as the hub assembly holds it in position? I don't have any fluid leaking so the seal must be good, or am I missing something. I am trying to do this in 30 degree weather and it sucks.
View 10 RepliesTo those of you that have replaced your unit bearing hubs on your 4 x 4's; are they giving comparable service to the OEM units? I'm replacing ball-joints right now and it would sure be easy to slap on some new hubs. The only issue is I have 130k on the originals and have been lubing them through the ABS port for the last 20k miles - the hubs seem to be in good condition. I've noticed some posters stating that since lubing an already good hub, that they are now getting a lot more than the standard 150k out of them. I also worry about replacing perfectly good US bearing hubs with most likely a Chinese bearing hub (Timken or not!).
View 10 RepliesI have a 99.5 with 400,000. on the engine. It has been a great truck but it is time for the some TLC. I have a little leak on the radiator and the water pump and would like to replace it. I am just looking for stock.
I have a 13 yr old that grew up sitting on my lap as we drove the dirt roads around the house and on the ranch. He has been driving this truck by himself (on the ranch) as soon as he was able to reach the pedals, around 8 or 9. His happiest day will be when he gets his drivers license and can drive the truck to school. So I have a lot of work ahead of me on this truck.
Rebuilding my 7.3 and I'm in need of the removal and install tool for the injector sleeves/cups for the 7.3 Powerstroke Diesel.
I'll pay all shipping charges and a small fee if required. I hate purchasing a tool I'll never need again, rather better not need.
So i bought a Aluminum Flatbed to replace my rotted bed. Its about to blow off going down the road at this point. The new Flatbed is Aluminum with LED lights. I suspect i will need to wire in a load reducercorrect? Also this bed has no fuel spout so i need to fabricate something. I also plan on installing underbed tool boxes if there is space.
View 11 Replies