Noticed a while back that the plug for what I assume is the air intake temp sensor is looped. I assume because I can't find the sensor anywhere. how critical is the sensor? The new S&B has a hole for it so it's either gonna need a new sensor or a plug. The local autozone has one for 16.99.
View 12 RepliesI have a code for iat sensor 1 circuit high. It's the only code I can pull. I replaced the sensor in the manifold and still no change. The truck revs up when started but kinda finds its idle rpm after a second and the idle fluctuates some when the truck is warmed up too. I have a snap on solus and all parameters seem to be good. Icp sensor is also new thinking it might be the cause. Other than that the truck runs perfect and doesn't miss a beat.
View 14 RepliesFor some reason my OH display decided to show 140 deg F when its 40 deg F outside. Continues to show 140 all the time now regardless of out side temp. In case its the related outside temp sensor sending unit, where it is exactly on an 02. Unless someone has solution may try changing that out to see if that is the problem?
View 14 RepliesI drove my 99.5 7.3 F-350 1 mile to a friends and hooked it to the OBDII to get a code for my abs light.it had not been drove all day. we hooked into the pcm and he noticed the temp at 375* it was idling. is this right he didnt think it should have been that high???Will the engine coolant temp sensor, if it were bad,show a high temp of 375*? On the OBDII it showed a temp of 375* .....
View 14 RepliesPlugged in my ScanGaugeII on a whim, it's usually on my 6.5 Suburban daily drivers, but was curious to monitor a few things on the 7.3
Noticed this right away, coolant temp reading a solid -40*F and never budging.
I was going to order a ECT gauge and was wondering where to mount the sensor. I have already used the port under the T-stat for the coolant filter. The gauge sensor is a 1/8 NPT. Would the block drains be a good location, or is there another location that will work.
I know the coolant filter housing has a port, but I would prefer the sensor be on the motor.
Coolant temps getting much higher than oil temps under load. Is there any problem that could cause this other than a bad temperature sensor? Reading temps with an Edge CTS 2 monitor. Think I'm going to hook up a mechanical gauge in the morning and see what it shows.
View 8 RepliesMy 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ....
What does it mean when you find oil in in the cold air intake, is this normal?
View 14 RepliesWhile doing a visual inspection I noticed that the AIH hot wire (captured nut wire) had broken off and was laying loose. I removed the wire from the relay and made a new 8 gauge wire, I connected it to the relay and was about to add it to the AIH when I got a healthy spark ( it touched the ground wire ) and yes the truck was not running and the key was out at the time.
This sounds to me like the relay has gone south, am I right??? I have a new OEM relay to install but I have a question. In what order are the wires and ceramic fitting go on the AIH post???
Dumb question but how do I remove the air filter intake from the turbo Its a little oily there from a fuel or oil leak but I dont see a clamp holding it on the turbo?
Also what is the e clip? Is it the little thing holding the wastegate rod on the exhaust turbine? Can I just pull the rod up off the clip?
I own a 2003 E450 (transit bus conversion) with a 7.3L w/ California emissions. I recently noticed I have a considerable amount of oil in my air intake going back all the way to my turbo starting where the crankcase breather tube attached to the air tube. The breather seems to have some sort of filter housing that is attached to the top of the valve cover. I removed it and it appears to be fairly heavy as in if it's a filter, perhaps it's full. If I'm getting oil into my air intake from where the breather tube comes off that housing and joins in my air tube back to the turbo, could that filter or housing have gone bad? It appears to be a dealer stock item only for 225. I've saw on the web people posting "reroute kits" for the 6.0L but nothing for the 7.3. Does this part simply need replaced or could I be facing a separate issue as to why I'm getting oil in my air tube?
View 14 RepliesAir Intake Heater Plug Code Eliminator P0541
In conjunction with the AIH Delete Plug??
Put in my new S&B intake today and when I stomp on the gas I am getting a loud shuddering noise from the intake when I change gears. Also sounds like a squealing sound sometimes. Doesn't sound like other trucks that I have heard. What that could be?
View 14 RepliesI notice my trans temp gets really hot fast. For instance just moving my trailer from front of my house to side yard makes temp go to 250. Without any load and driving a couple miles it does the same thing. It's been doing it since I installed the trans temp gauge just trying to figure out what's up.
View 14 RepliesI've searched, and gone back through my computer history and can't find it. I have seen a thread here which Mark contributed too which said what the max temps were and for how long etc. I know book is 230 and optimum is around 165 but there was some degree of play in that.
View 8 Replies I wanted to specifically ask about the block heater though. Since I bought this truck I never was able to start the truck without plugging it in. Now that it's not running I'm thinking much more about the block heater.
Is 56 too low for this old truck to start? What temp should a block heater have the oil temp as seen by AE be?
I live in the southwest so it's not very cold here. plugging in the heater was even required in the summer unless the truck had been running. What kinds of engine trouble would require being plugged in in warm conditions?
I will start off with saying I am posting this for my dad. His truck is a 1999 F350 crew cab DRW 4x4 auto 7.3 with about 189K miles on it. He is leaving wednesday on a cross country road trip pulling a 40FT 5th wheel (no idea the weight but the thing is huge). He has glowshift gauges installed, one of which is the trans temp gauge. I believe the transmissions on these are 4R100, but I am not positive about that, but I'm sure many people here will know. He just told me that he had the mechanic he goes to replace the pan gasket on the transmission because it leaked quite a bit, just as a precaution. He also had them replace the brake booster as it was leaking inside by the brake pedal. When he got it back, he said he was driving it, and the temperature started going up to I believe 220 degrees not pulling anything. He said since he installed the gauges it has been between 180-190, and it jumped to 220.
What this could be. I have read that the TFT sensor can cause this issue, but it would throw a code and possibly go into limp mode. He has no check engine light and it was driving just fine. So the temperature is just all of a sudden high. Fluid level is fine, was checked after about an hour of driving, is red, and doesn't smell bad. I am suspecting the temperature isn't actually hotter, so there is another issue. It's only a big deal now because in a few days he will be dragging a huge 5th wheel behind him.
Last year, we towed some pile of crap 5th wheel down to our city for somebody with his truck, and we had to pull over halfway back because it started to smell like something burning. We think it was the trailer, as the brakes were questionable on them. When we got it to the people we were delivering it to, when we left, it wouldn't shift passed 2nd gear. He only lived a few miles from there, so he drove it home, parked it, then went out the next day and it was fine. He had the fluid flushed later and that issue hasn't come back since. No other work was performed on it since the pan gasket a few days ago. I am not sure if they are related being a year apart, but figured I'd mention it anyways.
i have a 99 f250 7.3 powerstroke. the cam sensor was acting up. that what the scan tool said. i replaced the cam position sensor yesterday, and the truck is still acting up. the motor hitches and will shut off randomly. it tripped the check engine light, and the code is the "cam position sensor" once the truck is warmed up and shut down for like 10 minutes the sensor will not act up anymore. if i just start the truck and run it, even once it is up to tempature it will act up. but if i shut the truck down for about 10 minutes, it goes away. is there something else that could be causing this?
View 14 RepliesI've read some treads on the temp gauge sending unit but I'm a little foggy on where to look for my problem. I just purchased a 2000 F250 7.3, temp gauge not working. It has a new sending unit. I read some threads about the voltage at the plug but I have no voltage on either side of the plug. The way I understand it red/white wire goes to the battery. Is there a fuse between them and which one is it? and if fuse is ok is there a cronic problem that someone might know of that I can look for?
View 7 RepliesI have an new to me 1999 4x4 F350 that I was giving a good once over today on the front end since it wanders a little bit. but anyways I didnt see a abs sensor wire on the front. the plugs are there behind the inner fender well and it looks like there is a plug when the sensor should go in the wheel bearing. was 2 wheel abs an option on these trucks? is there anything else this changes front end wise?
View 14 Replies