99.5 7.3. 201,450 miles, Just developed a new noise. Was on interstate, in cruise, 65 mph, started while pulling a hill. Kicked it out of cruise and noise went away. I have found it will repeat just pulling a hill at highway speed.
Now for the noise....it almost sounds like lightly opening the secondaries on a gasser 4 barrel. I don't see anything unusual under the hood.
I just got my new up pipes put on as well as a 38R and pulling a hill hard my truck will hit about 22 psi then drop off slowly I have an electronic boost fooler wich has been on the truck since new pretty much but I don't get a CEL at all is this what I should be getting and I was on the 80hp tune? I ordered new boots and plenum inserts they just haven't got here yet. I know I had a leak before on my old up pipes because they rattled every now and then and I could see exhaust coming out of them when it was cold out but I could hit about the same 22 boost with my old setup. So pretty much nothing changed boost wise except it gets up to boost faster now. I would say it's defueling but I was always told the CEL would come on if that was the case.
View 13 Replies2011 ford f350, 200,000 miles. I was getting an antifreeze spray on the windshield while pulling and going up a hill. It was from exhaust pressure going into the coolant system. It was building over 16 psi and blowing out the degas bottle.
View 14 RepliesDecided to try a new wheel to see if I can stop the surge during hill climbing with our 5er. Old wheel looked great with no dusting or nicks. New wheel sure has a whirl when it spools up, but sounds cool. Haven't pulled trailer since swap yet. Truck still only has 85k on the clock.
View 7 RepliesWhile pulling onto the highway and pulling pretty hard lost engine power all boost then engine truned off. Top of engine is covered in oil..... What happened?
View 11 RepliesWas climbing a steep hill at 35 mph just before truck down shifted to 2nd, I was hearing a pinging sound. Sounded like only I cylinder was doing so. What it could be. I am currently running a 1/4 tank of Fppf fuel injector cleaner. Is this a injector noise. No knocking just a slight pinging.
View 1 RepliesI've got a 2002 F350 DRW 7.3 truck I'm having a little concern over. It started this summer, when under very heavy pulling I was getting a very noticeable vibration between 20 and 25 mph. I did not think much of it, as it only happened under extreme conditions.
Now I'm getting the vibration all the time, and it's started another band which is 40 to 45 mph. It's much worse if you are very light on the throttle, if you're full throttle it's much harder to notice.
Truck has 154,000 miles.
Today I visited a buddy who lives on a pretty steep hill. I always set my E-brake while in Neutral to make sure it's holding the truck before sliding it into park. So I got out and unloaded a few things and was in his garage. I heard a skidding sound outside, I was about 40 feet away from it when I looked out my truck was skidding down the hill!
I ran out and to the drivers door, opened it and pressed on the brakes with left hand right when it hit the bottom of the hill and it barely stopped from hitting the blue car parked on bottom of the hill. Next time if I stop on this hill I'll make sure it''s nose up hill and make sure I have 4X4 engaged to have all wheels locked up. I know this probably happened because the lack of weight on the rear wheels but this was a pretty crazy scare with only 7800 miles on her!
You can see the skid marks from my rear wheels, my friend lives in the middle of the block.
I have a 2001 F350 with a PCM labeled "PMT2".
The SES light is triggered every time I try and pull fault codes using Torque Pro. It has done this since I installed Torque Pro many months ago. Same thing happens in another local member's (2000) truck, although I don't know his PCM version.
I'm very comfortable with the Torque Pro settings that have been detailed in other Torque Pro threads. I have been careful to choose conservative settings, including trying debug mode. I have uninstalled and reinstalled Torque Pro to see if that solves the problem - which it does not.
Question: "PMT2" PCM been able to pull fault codes using Torque Pro without tripping the SES light?
I realize another variable may be my OBD2 Bluetooth device. As an aside, I have removed the AIH and would expect to see a fault code but Torque Pro reports no fault codes.
So I'm getting ready to pull my engine to redo my timing cover.. my engine has over 320000 miles on it and it runs strong, dyno'd 402 hp at the wheels recently.. I was considering dropping a reman in since im pulling the engine anyway... I heard you can test for blow by buy sitting your oil cap over the spout and seeing if the cap blows off.. well the engine tilts downward in the back so the cap just slides off but in the dark when i shine a flashlight you can see the fumes just billowing out... how do i know if this is too much... what else can i do EASILY to see if my engine has issues before i start taring it down?
View 10 RepliesMy transfer case engages the front drive shaft spins but even when I manually lock my hubs neither of my tires will pull! I was thinking either the hubs are shot but I was told it could be the 4wd locking solenoid??
View 1 RepliesI have posted a pic of a smoke issue I am having while pulling.
I just pulled a 10,000 lb trailer up a few 7% grades at 8-10,000 ft and the best I could do was 40-45 mph at 6mpg. Every hill would set a P1211 and when the truck downshifted to 3rd the smoke would go away for the most part.
Truck is 100% stock and pulls the same as my F350 with 3.73 gears but smokes a lot more.
The smoke is kind of annoying and performance seems sluggish especially given the 4.88 gearing. Where to start?
Has new ipr, hpop, icp, fuel filter, air filter, fresh 5w40 mobil 1.
Resealed HPOP, reinstalled, started right up, ran for good half hr, shut it down, started it next day, ran for 15 min. Revved it up, n all that, good to go, took it for a spin around block, died as pulling into driveway. At crank Dashcmd shows 200 psi on HPOP. I'm double checking the gear bolt right now. When I installed the pump I seated the gear by hand n torqued bolt to spec, so idk...
View 3 RepliesI have 2003 f250 7.3 automatic 181,000 miles completely stock. Never had chip,tuner or anything on it. I am second owner and got it when it had 70,000 miles on it. Ok here we go I live on top of a mountain and soon as i start up the mountain or any steep hill, or pull or tow something my service engine light pops on. First time it came on I took it to diesel shop they hooked it up to scanner and said it was code p1211 said icp sensor was bad so they put new one on. Couple days later light started popping back on so i decided to order a auto ingenuity after doing some research.
Hooked up to truck started up mountain while scanning at wot light pops on code p1211 and think it was live data I remember seeing icp pressure at 1922 and duty cycle at 63% i was trying to drive and read it at same time and my lap top went dead. What does this reading mean 1922 pressure/ at 63% cycle done little research but dont really understand. Year and half ago replaced all orings on all injectors, new rebuilt hpop pump. New ipr valve, glow plugs, past month 2 different icp sensor new,and new ipr valve new pig tails on both and light still popping on.
I was driving up a hill an it started to loose power. i got up to the top of the highway an stopped an it just shut down. got towed home i thought it could of been the alternator but dose not seem to be. took the belt off to spin the motor an its not spinning. drained the oil an there is no metal in it to see if the motor was done. i try to start it an it just dose a click click an that's it. Is the motor done or is it a transmission problem?
View 3 RepliesI have a 2001 F350 with a 7.3 diesel and automatic trans. I purchased it about 100,000 miles ago. It is all stock as far as I know. The mileage on it was about 14-15 on the road and I decided to put a chip in it. I was somewhat leary of putting too much power to this old of a rig. I put a TS Performance chip in it. It seems to have more power. I am towing a 30 ft. Gulfstream Seahawk I think around 10,000 lbs. When I started up a hill it made a different noise like a screeching noise when I pushed it. When I back off a bit the noise goes away. When I put it back to stock setting the noise is not there just the normal downshift and increased RPM. Not sure how to describe the noise but sounds like a metal bearing type noise. I get the same rush of air or what ever that sound is when it changes back to a higher gear. Is this sound normal or what might it be. It sounds normal when not pressing it.
View 6 RepliesI have a 2006 f-250 super duty with a 6.0 and auto trans. I was pulling a trailer with about 5k of vehicle on the trailer.
Problem : after a long trip on good roads, I had to pull a steep hill. climbing the hill i did not shift into tow mode and all of a sudden my engine raced up to about 3k rpms and seemed to either shift to low or ( maybe ?) the Governor may engaged ?
Anyway I made it to the top of the grade and it seemed to be fine from there.
Question Is the trans broken, or did the computer maybe try to protect the trans ? It seems to work fine still?
Thought batteries were bad and replaced batteries truck started and ran. Shut it off and went to restart 30 minutes later and had no power what so ever like no batteries were in it. Put new batteries on charger the were full so hooked batteries back up and it starts. 10 minutes later same as before like there was no batteries in it. 2001 7.3 464,000 miles
View 4 RepliesI was driving my truck then all sudden truck started losing power then slowly died. I restarted it, it was a lil shacky then died again. Iunscrewed the fuel filter and looked in the housing and there was lil fuel in bowl i turned the key to on position and bowl did not fill with fuel looked as if it were shooting some bubbles up(air) could it be outta of fuel???
View 10 RepliesA few weeks ago I replaced my CPS on the 99 7.3. Today was the first day I drove my truck in the rain. When I turned my wipers on, I noticed that I lost power and my truck started hiccuping. I read on these forums that an aftermarket CPS is most likely the problem, so I am planning on getting a ford CPS this afternoon. My biggest concern is that before I replaced my CPS, my wipers only had 2 speeds. Also, if I pressed the end of the blinker switch to squirt the cleaner the wipers would not turn off until I turned the truck off. I am not sure why this would be happening and I wanted to ask if there is more than just the CPS involved with this.
View 7 RepliesDriving home from movies tonight, I lost power steering and power brakes and the pump started growling. Looked in the reservoir and it was all foamed up. Within the last 20k mi I have flushed the system and refilled with power steering fluid. No apparent leaks at this time. And happened like someone flipped a switch. Fine one turn, nothing the next. What are the chances this is a fluid issue and not a mechanical one? Start with flushing system and adding Mercon V? Or is it likely pump is damaged?
View 7 Replies