So for a while my truck sometimes and sometimes won't go into idle when I floor it and I've been trying to get the code and I finally got it it's tps high voltage so faulty tps??
View 1 RepliesI've been working on my truck for months now on and off. I thought i finally had it back, but i have (again) problems with running. it basically only ran for a full day (hauling trip) after getting it back up and running. next day, it died on me on the road.
The new deal right now is that I can make the truck start and it will run, but it has little "hiccups" or misfires that will happen every now and then. Once it gets warm enough, the idling sounds chopped (best way i can explain it). After "chopping" it will then run fine (until the next chop). then it seems that once the truck gets warm it just stalls out. When that happens (shutting off) i can't get it to start right away. i have to wait awhile before it'll start and that lasts only so long.
The truck puffs a tiny bit of white smoke. not constant but more like a "puh - puh - puh" ....I've changed out quite a bit of used up parts now...
Turbo
Injectors & wiring harness
valve seals
IDM
ICP
IPR
CPS
MAP
fuel pump
vacuum pump
glow plug relay
starter relay
All the sensors are OEM. There's fuel in the fuel bowl, and the filter is clean. Plenty of oil in HPOP & oil level in crankcase is good. Have plenty of fuel.
Air filter is clean and fine. No codes. No lights.
2001 f350 7.3 320k on it.
I just installed glow plugs, ucvh, stage 2 rosewood injectors, t500, ipr and gear head tunes. I have out 97 miles on the truck since all this was installed and the truck seems to run okay but has a rough idle and sounds like there is a mis? What should I look into first?
View 12 RepliesI bought a 7.3 f250 with 300k mi. It had a battery light on but didn't show any signs of trouble. Eventually started dropping volts a few days later and I replaced the alternator. The light is still on and flickers in time with the idle of the truck and sometimes goes out when I'm on the gas pedal. Some nights when the lights are on the voltage drops ever so slowly until its drained. Why the new alternator didn't fix the problem? NAPA's scanner says the truck has 12.4V at idle and 12.1V at idle with the lights on. Batteries are relatively new and test fine, dual Interstate Mega-tron Plus batteries-top of the line.
View 6 RepliesI have a little problem with my 1999 f250 7.3 power stroke diesel. Every once in awhile, while driving the truck would die completely but i switch it into neutral and started right up. What could be the problem?
View 9 RepliesI have a 2003 7.3. Suddenly a week ago when I left work, I noticed my truck wasn't picking up much, but i was in a 40mph zone. I then jumped on the freeway and noticed the truck would not go over 60mph. Once I exited and got on another road with a 55mph speed limit, the truck would not go over 45mph, I had the pedal pressed all the way down and would not go over 2000 rpms. Also, for the transmission to shift, I would have to let off the accelerator.
View 1 RepliesI have a e99 f350 7.3 all stock. I have no power. The truck will crank for about 15-20sec before it'll turn over. I just purchased the*AE*but am fairly new to understanding it all. In idle its a little rough and when I drive I can only stay in the neighborhood because of fear of getting rearended due to very slow acceleration. Whats weird is that when i have no power while i am driving ill keep the pedal down throw it in nuetral and my rpms and*icp*pressure jump up right away. Things I've replaced:
Icp*sensor
Fuel pump
Pcm
Tps
Cps
Ipr
Dropped tanked and cleaned screens
When cranking my*icp*pressure climbs slowly to right under 500. I dont know what else to do ive been working on this truck dor two months some days 13hs straight, I am feeling defeated. Codes p1249 1211 1209....
2002 f250 7.3l diesel...
I got a new radiator and the tranny fluid was the worst the mechanic had ever seen. He serviced it and warned me that it might not be long for this world. I broke my flexplate and so I had to pull the tranny, and I decided to throw a new torque converter in because it was giving g me symptoms like a broken sprag( it wouldn't rev up or do a brake stand in gear, therefore slow takeoffs).
I was recommended to replace the tranny, I decided I could do the job again down the road if I needed to. About two thousand miles down the road I had a hard shift going from overdrive down to get up a hill and about 10 miles later the truck started slowing down....I couldn't give it enough pedal to keep it going and the engine sounded rough.
I pulled over and checked fluids and everything was fine, truck idled fine, bright red tranny fluid not burnt at all. Pulled on to the road again and it pulled fine until about 40 mph and it wouldn't go any faster. I got it towed home and ordered up a tranny from Ford figuring it must be toast, but I thought I'd throw it out to the forum to see if there is any other troubleshooting I can do before I install the new one in case it is some other problem or some electrical harness or something, or if that is a pretty standard reaction to a fried tranny.
Engine runs good at idle, shifts perfectly to drive and reverse, drives forward and back(I'm very hesitant to drive it out of the driveway in case I can't get it back in). Only happened two times before I decided to tow it. Temps looked fine on the gauges, fluid was a little overfilled in the tranny, but again, not hot or burnt.
Problem started 2 days ago, driving around and my truck would stumble and lose power. Give it gas, won't rev up but it cleared and ran fine for a mile or so then it comes back (off and on all the way home). Check engine light didn't come on the first few times, came on a couple times on the way home (maybe 4 mile trip) but goes off when the truck runs fine. Thinking it was maybe the fuel pump (got 140K on the stocker). Talked to a few friends, some thought it was algae build up in the tank that was clogging the filter on the pump, underhood filter changed a couple hundred miles ago. Looked fine with slight brown build up at bottom of bowl when I replaced it.
Ran it around yesterday with a friend of mine and his scan tool hooked up, acted up once, check engine came on for a few seconds and shutoff. No code and for some reason we couldn't get it to live data while driving. I dumped in an algae eater yesterday and left the truck overnight since I had to work. Got home this morning to run her around the block to circulate the eater. Truck started and idled fine, went to pull out and she won't rev up, pumped the gas and NOTHING! Check engine light is on now but don't have a scan tool handy to read it. I heard the truck will store the code?
What this problem might be? What's a good scan tool for our trucks that can live data as well? CPS is good and already did the UVCH mod.
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 RepliesI want test my fuel pressure. What is a good gauge or kit to buy? My truck has lost power towing and is now starting to miss a little. I'm wandering if i my problem is in the tank. Is there a good scan tool that would diagnose things too?
View 14 RepliesSo long story short I have a 99 f250 xl, 7.3 130k. Overall good truck but has no options, never had AC but would like to add it. I have seen the kits on bought4less. So I'm thinking all the factory parts should be bolt on, since the holes should be all there, and since most of the wiring should be there. I just need to collect all the parts. Also one question I have is, what goes through the firewall. Is it just the lines, or how does the ac get to the vents? Dumb question but don't get that part of it.
View 7 RepliesStarted truck 3 times in 30 min. no issues with truck before tonight nice well cared for truck. Went to get a pack of buns at store came out --NO CRANK--all lights are on dash, etc, new starter a month ago, relay changed out in fuse panel just to see if there was a change. Bought two new Motorcraft batteries installed , NO CHANGE, so is it natural safety, key switch, electrical ignition switch, solenoid on starter, is there a solenoid between key and starter?
View 12 RepliesMy brothers high mileage 7.3 ran out of gas because of a broken fuel pick up line. I brought him 10gal fuel, primed out of it and now the truck is sputtering and sounds like it's running on 2 cylinders. It's not just air in injectors or something it sounds like crap. It's getting fuel at least to the bowl.
View 14 RepliesI was driving my truck then all sudden truck started losing power then slowly died. I restarted it, it was a lil shacky then died again. Iunscrewed the fuel filter and looked in the housing and there was lil fuel in bowl i turned the key to on position and bowl did not fill with fuel looked as if it were shooting some bubbles up(air) could it be outta of fuel???
View 10 RepliesA few weeks ago I replaced my CPS on the 99 7.3. Today was the first day I drove my truck in the rain. When I turned my wipers on, I noticed that I lost power and my truck started hiccuping. I read on these forums that an aftermarket CPS is most likely the problem, so I am planning on getting a ford CPS this afternoon. My biggest concern is that before I replaced my CPS, my wipers only had 2 speeds. Also, if I pressed the end of the blinker switch to squirt the cleaner the wipers would not turn off until I turned the truck off. I am not sure why this would be happening and I wanted to ask if there is more than just the CPS involved with this.
View 7 RepliesTruck started losing power then service engine light came on, drove about another mile then it just stalled ( almost home lees than a 1/4 mile). Got out open hood oil everywhere on top of motor. Looked under truck and oil all over the road. Looked back where I was driving a line of oil as far an I could see. Checked oil barely any on stick. Where should I start hpop or plug?
View 7 RepliesI have a 2002 F250 Super Duty. Was driving it and it started to lose power and shut off. Then wouldn't start like out of fuel. No engine light no codes. Truck has 155k on it. So just because I replaced fuel pump. Truck runs but not right it's ruff no power kinda back fires in exhaust. I check wires and plugs under valve covers all seems ok. I ran truck and pulled each injector loose and engine would stumble. As in they are working. I replaced cps. Just because still the same. Then the truck started running right. But the truck runs but has knock but knock goes away and truck has full power. Yes oil is full and I change it regularly. The problem is off and on like electrical.
View 7 RepliesWhile headed back to town my 2000 f350 7.3 with 444,650 miles (I'm original owner) and have performed maintenance and repairs since mile 3. Truck started to loose power and eventually stalled, was able to restart several times to limp home 7 miles in one hell of a snow storm. Very confused, replaced cam position sensor ( keep one in jockey box ) replaced fuel filter truck starts then stalls out. Don't know if a bad HPOP would allow start up at all. Fuel pump???
View 6 RepliesOn the way to work, the truck seemed to have a miss at idle and the CE light came on. Long crank to start leaving work, and truck starts losing power and eventually died. No smoke while it was losing power. Towed it home and checked the fuel pump and lines for blockage and found nothing.
2003 7.3 F-250 430K miles
strong cranking but no start no smoke out exhaust
Oil changed recently
IPR changed
Both UVCH gaskets and pigtails have been repaired.
ICP sensor and harness changed, also disconnected no change in cranking.
fuel filter changed today (no oil in bowl)
3/4 tank of fuel
dash gauge for lpop goes up to normal range during cranking and oil light turns off.
WTS light comes on and turns off as normal
tach gauge moves up between 100-200 during cranking
fuel pump turns on and pressurizes system like normal and turns off.
Ordered AE for the truck, and it directed me to the passenger side bank high open. Fixed the harness on that side and still nothing.
Sent off the IDM and it passed with flying colors
So now i'm leaning towards the HPOP, but would hate to fork over the cash for it and still not get anywhere. I'm going to take the valve covers back off and check the discharge ports for the injectors tomorrow.
I know there are a few threads floating around regarding truck dieing, but mine is slightly different than the others, maybe its the same culprit, maybe not, but i thought i would start a new thread just in case.
First, I commute about 50 miles to work everyday, truck gets plenty of interstate highway run time, smooth as silk. About a month and half ago when i almost got to work I slowed to stop at a red light. As I came to a stop the truck "stumbled". Acted like it wanted to die but caught itself and kept going. I said whooaaaa girl, what this? Ive had this truck for almost 10 yrs now and never anything like this. About a week or so later, same commute, same red light, cept this time it dies. Starts right back up no problem. Just acted like someone turned the key off.
Then a week or so after that, while driving home this time, as I pulled up at the house to check the mail at the mailbox, when i came to a stop it died. Cranked right back up. Before I could put in drive, it died again. Cranked right back up and i drove on into the driveway. Then a few days later, while checking the mail again, it died again. Cranked up immediately and parked.
Today, while driving home, after i had gotten back to town, but before i got home i made a stop at bank drive thru, when i came to a stop, it died. While cranking it wanted to start and kind of stumbled on itself and died. Then it cranked right up and i came on home no problem.
So far it only occurs after approx 45min to 1 hr of operating time so the engine and everything else are at temp and far from cold. After reading thru some of the other threads of similar but different conditions (cold start dieing, dieing while under power, etc) Im getting flooded with ideas of what could cause it, but not settled on any.
1.Could be failing ICP? (original, has never been changed, 317k+).
2.Could be plugged fuel filters? (been a while since changing, approx 30k+)
3.Could related to one of my own earlier threads regarding possible failing alternator (when rpms drop can volts drop enough to kill engine?)
4.Could be loose ignition switch? (about 2 yrs ago i had to swap the blinker switch, to get to it had to remove the ignition. Upon re-installation the switch never did get tight as before and was loose. Been loose ever since. To the point that with key out of ignition and door ajar i will get the door chime as if the key was in ignition. I can bump the ignition, and chime goes away. Been this way for two years and no apparent problems. Until now maybe?)
I was thinking ICP after a few of the other threads, but after tonight Im leaning towards the ignition switch. I guess i can try to wiggle the switch after cranking tomorrow and see what that does for a trouble shooting effort. Is there a way to trouble shoot the ICP to see if its failing or not? Isn't that a fairly costly sensor? Would hate to buy one and not be the cause, but after 317k i may need to buy before too long anyway.