Ford Aerostar :: Revving High For 65 - 70 MPH / Shifter Wouldn't Go Into Reverse
Apr 29, 2011
I drove our 95 3.0l aero to work today, I was going to a job 45 miles away. It sounded like it was revving awfully high for 65-70mph, but the gear selecter said od, so I figured I was just crazy. Got to the job and tried to back up and the shifter wouldn't go into reverse. Parked for the day after realizing the shifter would go N and down, but not into rev or park. Apparently it was revving high, as the gear indicator was now off and I was no doubt in drive, driving to work. I got it home, then had to drop my daughter at work, by staying in OD.
Then on the way home the van just DIES while going 35+- mph. Won't restart, smelled gas after many many attempts to start. Towed home. NO spark. I have 12+ volts at+coil. I tried my ignition module and a new one, neither sparked at the coil wire. I bought a new coil, then checked resistance at + &-, and - and coil output post. Basically same resistance new & old coil. Did my hall effects or cam, or crank sensor just go out or? Why both problems same day? I thought if it was the coil or ignition module, maybe it got too warm on drive revving high. Does a 95 3.0 coil get triggered by the distrib haal effects or does the crank sensor do it?
I can easily see one of those being bad as they are original, with 334,000+ miles. All the tune up, coil, wires, plugs, ign module, cap, rotor, were replaced 55,000 miles ago. ALSO does this distrib have a TFI module on it? My book says to pull the distrib and remove it, like my 5.0l Mustang, but I don't see one, I think thats the ignition module on the pass. inner fender. I'd like to see if I can get 400,000 miles out of it.
View 4 Replies
Advertisement
We are planning on taking our 07 Explorer in to the dealer to have them check on a couple of issues. 4.0 with auto and about 45,000 miles on the ody.
1. While taking off after waiting at a stop light or slow speed traffic crawling there is a high revving sound coming from the engine compartment. Sounds like the fan is over revving compared to the engine speed.
2. Recently the truck has a hard time going into reverse. Physically hard to move the gear select lever and there is a hard "thunk" when it does actually shift into reverse.
I just want to be armed with information before heading to the dealer. The truck is still under a warranty plan, I just need to be prepared. Could it have to do with the Transmission Range/Position Sensor?
View 2 Replies
I have an 89 Ranger, 5 speed, 2wd, M50D transmission. On the way home tonight I was upshifting from a stop and when I went to go from 4th to 5th the shifter wouldn't budge. Luckily I was on a back road so I pulled off the road and tried all sorts of things (rolling truck while stopped, etc) and the shifter just will not budge.
Now here is the thing. I had my fiancé with me and no tools so I really couldn't do any diagnosing. However, 6 months ago I replaced the clutch, pressure plate, throwout bearing, slave cylinder, and pilot bearing. While I had the transmission out of the truck I changed the fluid, siliconed around the rubber plugs, and put a shift bushing kit in. The bushing kit is the bushings around the shift ball with new wave washers and new pins that insert into the ball.
It is obviously not related to the clutch as it engages/disengages properly. When this happened, there were no noises of any kind when I shifted from 3rd to 4th. It just will not come out of 4th. I am going to pull the shifter out tomorrow and have a look. Do you think one of the new pins that I drove in to hold the shift ball broke or fell out or something and if so would it cause this problem?
View 4 Replies
So I was driving on the highway a couple of days ago in my 2012 GTI and I noticed that I was really having trouble getting up to speed. I was going 65 mph and the speed increased to 70, so I tried going faster, only when I pressed down on the pedal nothing happened.
The car just kept revving. Later when I got the city I noticed that the car wouldn't shift, so I put it in manual mode and shifted it myself. Couple of hours later lo and behold the check engine light turns on.
The car is at the dealership now and I just found out it was the fuel pump. My car has only 26,544 miles on it and I have had it tuned by APR but I don't know if that caused the issue.
View 3 Replies
1995 3.0L 6 Cylinder Aero, aka the Green Goblin.
I've recently noticed that when I'm running between 50-65MPH the GG can't seem to decide whether it wants to stay in D or OD, I think. It's hard to tell whether or not the transmission is shifting or if it's just the engine revving. I don't have a tachometer but it's almost like the engine is revving /surges and then falls back, sometimes repeatedly. Could this be due to a vac line leak?
History- GG has 167K on it. I recently changed the oil, plugs, wires, distributor and air filter. Cleaned the MAF. Due to a failed AC compressor and low funds, had it removed and a bypass pulley installed. Needs a new pipe & muffler which is on the agenda.
View 14 Replies
My mom's 95 shifter is slowly getting worse. Right now it's at the point where we have to hunt for gears just to put it into park or reverse or d/od. It's not stiff like the rest of ours, hers is all sloppy and loose. She says it's been doing this for a while, but i think it got worse when i pulled her cluster out to change the light bulbs. I say this because i couldn't get the needle cable un done, so i just let the cluster rest on it while i was changing the bulbs, which put a little bit of tension on it.
View 14 Replies
I went to put the van in park, and the gear shifter just went all floppy in my hand. I was able to wiggle/jostle it around and get it into neutral or drive, but nothing else. Tow truck driver crawled under the van, and put it into drive for me, and told me it was probably just going to need a new cable or link shaft (tube shaped thing)... My hubby usually fixes these things, but is now living 1700 miles away.
Anyway, the shop called me and said I needed a new steering column, and said something about the 'lower' cap or half??? He quoted me $340 for the job. I am not getting the connection between the gear shifter being loose/floppy and the steering column needing to be replaced? Is this right?
It is a 1993 Aerostar, 3.0 by the way...
View 14 Replies
I have an '86 Aerostar with the 2.3 four and 5-speed stick. The shifter is sloppy, and it's often hard to find 4th when downshifting from 5th, and sometimes, it shifts hard through all the gears. Other times, it works fine. The manual says that this shifter was used from 86 to 89 only. Did they use the same one on Rangers? Can I buy a rebuild kit? Or, is this a sign of some other problem such as the clutch slave cylinder?
View 1 Replies
I got this code and symptoms of 1-2 hard shift and no torque converter lockup. No flashing overdrive light on shifter. If I switch off engine all shifts are smooth until I pass 45mph. I would feel the TCC lockup. This doesn't happen the as i come to a stop I get a harsh 2-1 shift. Key off restart then shifts smoothly up and down provided I dont exceed the TCC lockup speed. This leads me to the TCC solenoid I think. Fluid has been changed regularly.
Had to drive 300 miles to get home. Only for the plate trans cooler the fluid would have overheated as on inclines on cruise control the engine would rev to 3k to keep the speed at 70mph and I could see the fluid temp increasing. Fuel consumption was very bad almost a full tank (with no ac). Doing some research there is talk about valve gasket blowout Epc solenoids etc, though these were for Rangers and Explorers, no real mention of Aerostar.
View 14 Replies
I have a 89 f250 4x4 351W FI C6 Auto, recently I was having problems with the trans it was revving up real high before it went into 2nd. I dropped the pan and the valve body to make sure their were no shavings or any other debris. Everything ok.
So I replaced the valve modulator and the line that goes to the intake, replaced the MLPS and adjusted the intermediate band. I put it all back together and NOW it won't even go in gear. Did I hook up the valve body wrong? If so what is the proper way of doing it?
I only unbolted the valve body from the trans I didn't take it apart. I was also wondering whats up with the color strips on the modulator I have purple right now was i suppose to have different color? Could the pin for the modulator not be in place? I added 3 quarts is that to much or not enough?
View 6 Replies
My low miles (under 50k) 1999 Ranger has a 5-speed manual transmission. One morning, I could not move it. The shift lever shifted, but the gears were locked. No forward, no reverse, and it wouldn't roll in neutral. Eventually, I popped the clutch, and, with a loud BANG! restored itself.
Background: I had rolled the car up tot the curbing in my driveway, so the wheels touched, then shut it off (in gear) and finally set the emergency brake. I'm guessing that this caught the gears in a way that caused the problem.
Yes, it's running just fine now. What happened?
View 5 Replies
My ranger sounds like it's revving up real high when I take off but don't have much power. Know what this could be?
View 5 Replies
About a month ago I replaced my blower control module. I purchased the module from Rockauto. The first replacement module lasted about a month. I received a replacement because the blower stayed on high and wouldn't turn off. The second module only last one week, the blower once again only blows on high and won't shut off. Both replacement modules were made by Dorman. Could something be killing them or am I just getting crap parts?
View 5 Replies
1985 ranger 2.3L TK5 tranny. Shifter was really loose and the tranny finally got stuck in reverse. I have opened up the bottom cover, but am not sure where to move the shift forks to get it back to neutral. I bought a new shifter, but I need to get the tranny back to neutral before I can install it.
View 2 Replies
1999 windstar transmission. Daughter drives van,never had any problems and suddenly no drive or reverse.Put it in gear ,no rpm drop, same for reverse.I put it in park and it will not roll so I don't believe its a linkage issue. Its like it has no torque converter. Fluid is at the full mark,and has no burnt smell . Its been my experience that a trans. Usually starts slipping,or no up shift or makes some noises when its getting ready to puke. She stopped for a stop light, went to take off and it just rev-ed up like it was in neutral.
View 3 Replies
My cousin has a 2007 Ford Taurus with the pushrod 3.0L. It has the console shifter and it is hard to move the shift lever into Park from Reverse. The shifer moves out of park and to every other gear with normal effort. The gear indicator correctly displays the shifter position. It drives/shifts perfectly fine. The only problem is that it is hard to move the shifter from Reverse into Park. It feels like there is a rubbery, or somewhat mushy threshold/resistance that needs to be overcome with a moderate amount of effort to get the shifter into park. Once the shifter is in Park it feels normal meaning you don't have to hold or force the shifter to stay in park.
It is frustrating because it seems most other people have a problem with the shfiter being hard to move from Park to Reverse or Neutral, but she is having the opposite issue. Will it hurt the car to keep shoving the shifter into park when necessary without getting it fixed?
View 3 Replies
Two days ago, I was driving on a North GA steep, windy, mountain road in my 2002 v6 4.0 Ranger. All of a sudden, i started revving real high (about 4000rpms) and getting no power (20mph). I pulled over immediately and transmission fluid was pouring, by the quart, out of my truck. I didnt get to look exactly where it was coming from, since i backed away once i saw a small flame coming from the leak. i then called a tow truck (assuming it was a seal or a hose break) and had it towed to my house.
I started investigating the possible problems and didn't really see anything noticeable under the truck (not that I was expecting to). So what I did was put three quarts of transmission fluid in the dipstick hole and put in gear to see if I could spot a leak. nothing. then I drove it around the block to get it warmed up and put a little pressure on the transmission by driving up a semi-steep hill to see if that would spark the leak again. still no sign of the a leak.
And finally, when I went to go check the dipstick after my test drive, it read to be above the cross hatched area, hence being overfull. What my next step should be?
View 6 Replies
My reverse lights and back up alarm will not engage unless i hold up on the shifter while in reverse the only thing i found was a adjuster for the indicator....
View 14 Replies
My son called me today to pick him up. His 98 S10 would shift into gear but wouldn't go forward or into reverse. New clutch 6 months ago, hoping something simple like low gear oil or worse?
View 1 Replies
I have a 1997 ford aerostar van that i recently acquired through some family,when i got it it was running fine but has recently started having troubles.The Question i have is this i put my car in drive or reverse and push the gas pedal the car doesn't move.....we have tried putting transmission fluid into it and that worked temporarily. What it could be except just a bad transmission?
View 2 Replies
Catfish is a '96 4wd extended doggie RV, with 175k. It has developed transmission selector problems in the last few weeks.
The shift selector stops seem to be going soft. It's not to bad going from P to OD, but I have to fiddle with the lever almost every time I put it into reverse.
Particularly harrowing when trying to do a quick turn around in traffic. What's going on here and what I need to do to fix it.
View 12 Replies
