im trying to lift my truck to clear 44's its a 88 f250 ext cab long bed, I will be using a dana 60 front and stearling 10 1/4 rear, if I get 6 inch lifted leafs front n back with my 3 inch body lift is 9 inchs enouph? If not will it be atleast high enough for 40s?
View 1 RepliesI have a 1994 Black Ford F150 and i was wondering if i could lift the truck 6 inches only using lift blocks (or any other cheap way to get my truck off the ground)....
View 2 RepliesI have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 RepliesI have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 RepliesIf this was my car or older truck I would know what the deal was. First hill I came down in my recently bought 2003 F250 the pedal pulsed a bit as I tried to slow down...is this the way ABS brakes behave? Never had them on a truck before...she stopped ok but don't know if they are warped or normal ...I'll pull wheels later (not a daily driver)...
View 7 RepliesBrake issues 2003 f250 super duty 6.0. Changed master cylinder, drivers side rear brake hose, new pads all around. Pedal is good at times for a few seconds. I've bled them all numerous times truck running or not flushed power steering pump new fluid. Brakes are spongy or go to floor. Do I need a scanner?
View 2 RepliesI have a 1999 f250 super duty, that was wrecked a few months ago. I have put the truck back together with the mechanic. The front drivers side was wrecked. The power steering fluid tank was cracked and had to be replaced. Also had problems with a box behind the drivers headlight? I did hard wire it together and it fixed the problems i was having the the speedometer and the transmission not shifting correctly.
Everything is put back together now but I drove it today and the brakes locked down after driving it a few miles? Had to push the truck hard to get it back to my house, a mile or so. If i let off the gas it would come to a quick stop. It is ALL four brakes locking up. If it sits for awhile they unlock but will lock up again after driving. The truck is lifted and the ABS light has come on.
It was not on before but i am pretty sure the ABS is disabled on the truck. the wires are hanging down by each tire. This is how they truck was when i bought it. Not sure what is causing the brakes to lock up.
Before I get started... My truck is a 2006 F-250 Super Duty XLT 6-speed 4x4 with a Limited Slip.
I just got finished with a big job on my truck. New pads all the way around, turned rotors, new emergency brake shoes, hardware, and backing plate as well as replaced the rear wheel bearings both inner and outer as well as the axle o-ring and inner seal. Also, took off the rear pumpkin cover painted it and put fresh fluid in, went with Mobil 1 75W140 LS.
Took it for a drive and the brakes work great. Followed the directions for breaking in the emergency brake which worked fine.
Now the problem is I'm getting rattling from possibly all of the wheels. Definitely from the front driver and at least one of the rear wheels. It was so dark I didn't get a chance to look at it I just pulled it back in driveway.
I'll start looking at things tomorrow but, any common mistakes or things I should check first?
I took the 88 out yesterday (3.0 with rebuilt transmission).. it looks like there is transmission fluid on the back (spots all over it).. I can only assume it's transmission fluid... I tried to wipe it off... but it was kind of a mist.. I assume the modulator should be checked? I'm not sure where it is or what it looks like though...
View 14 Replies 92 F250 4x4 with 140,000 mi. Abs light came on, Replaced the sensor on the rear axle, Light is still on. When the light comes on the brakes still work but it takes more pedal to stop. Now the Brake light comes on, It has new pads on the front, and its bleed out good. When you drive it some times it works fine, then out of the blue it lights up.
I have checked the fluid level, parking brake switch, and even swapped the abs black box with another, also bleed the bleeder on the left frame rail. When the lights come on you can pull off the road and turn off the motor and restart the lights stay off for several brake applies, then sometimes they light back up. The light issue is not that bad to me but it drives my wife crazy. I am more concerned about it taking more/harder pedal to stop.
Looking to replace the steering stabilizer on my 2008 F-250. It has a 6" lift and 37" tires.
Also, does "dual" mean better?
My buddy just bought a 1992 f250 460 the brake suck the pedal goes to the floor don't know if master or the booster or the rod needs to be adjusted or what the brake look ok and it stops ???
View 7 RepliesMy problem, Brakes. I hardly have any at all (pedal all the way to the floor and hardly stop), yet the front pads are dragging, and heating the rotors. Maybe a bent line? I bled the fronts, and as soon as I loosened the bleeder nipple, a good bit of fluid came out, without pressing the pedal of course. It's dark out now or I would inspect for bent lines. Could there maybe a problem with the booster?
View 6 Replies2000 f250 with v10, got home from work today, then short time later we were going out again and my steering was extremely loose. Basically you could swing the wheel and it spins around. Power steering fluid was empty and I refilled it but still the same problem. Is there possibility that I'm just not using a thick enough power steering fluid?
View 1 RepliesSo it looks like there is no adjustment on the Parking Brake on this ride other than adjusting the shoes up. As far as I can see my Parking Brake should work like a champ, but it won't hold on much of a hill. I have new shoes, new drums and it is adjusted up so I can hear them drag. I can actually feel it getting tight then looser as you spin the wheel, like one of the new drums is slightly out of round, so I don't think I could go much tighter. Is it possible one or more of the cables is stretched? I did see the shoes spread when I had the drums off and I stepped on the Park Brake, so I know things are working at least that much.
View 2 RepliesMy 2003 F-250 5.4L 2WD has a front end vibration that starts around 40MPH (sometimes) and gets gradually worse until it goes away at 55 MPH. It oscillates the wheel a good 3/4"-1". It also does it also when decelerating through those speeds. It "feels" like the left side, but I can't be sure. When I jacked it up, I could get some movement laterally on the left wheel, but not the right. Also Noticed that the drive shaft has about 1/4" of play at the carrier bearing. Leaning towards ball joints.
View 2 RepliesTrying to change the pads on my 2003 F250. One of the boots is not retracting smoothly. Any recommendations?
I can't get the caliper to bolt back on and I think this is the issue.
So lets see if I can put my issue into writing....
Have an 02 f250 v10, last summer replaced the steering gear box, havent had any issues til this spring.
Beginning of spring my ABS light came on during casual driving, wasn't to worried as the rear sensor often gets dirty and needs cleaned- cleaned the sensor and the light remained on this time.
While driving (and the light being on) I would at random get a very heavy vibration/shake from the front end and if I apply the brakes while that was happening the truck would pull real hard to the right, the shaking feels like a death rattle- like the ABS was firing and was using steroids, then it would go away. (the brakes would occasionally smoke a bit on the left front side afterwords)
So like that problem wasn't annoying enough, while trying to diagnose the problem the ABS light clicked off, and I wasn't able to recreate the vibration, but I noticed when I would apply the brakes, at say a stop sign, the brake would press in another inch or so (after already being stopped) and then I could hear a loud whine from under the hood.
The fun is these 2 problems seem to keep swapping positions- and I am at a loss of what could potentially be the cause- (I assumed the 2nd problem where after stopping the break pedal going soft another inch and the whine could of been air in the system- I bled the brakes and no change)...
My 2012 F250 4x4 tire pressure warning message/warning light it on, I have checked all tire pressures, they seem fine, i s this a common problem and what normally has to be done to fix the issue...
View 14 Replies