Ford - Escape :: 2002 - Misfiring / Brakes Also Went Out
Apr 7, 2015
Less than 2 months ago I bought a 2002 Ford Escape with 165000 miles. It has been nothing but trouble. 3 days after I bought it, it misfired for the first time. It stopped on its own and I let it go because that day the brakes also went out.
It seemed fine for a few weeks and then the check engine light came on it was a code for the 02 censor. Some fuel injector cleaner did the trick.
A week later it started misfiring again. I couldn't drive it to get the code checked so I replaced the coil pack on the cylinder that misfired last time. I drove it that night it wasn't misfiring but it would barely get to 50 mph. When I tried to start it again it made a loud squealing when I press the gas. I still don't have a CEL.
View 12 Replies
Advertisement
I had a misfire and my CEL came on had it read and it said cylinder 4 was misfiring and that there was a misfire in the first 1,000 RPM's. I replaced the COP and plug and now I'm getting terrible MPG. I tried to reset the PCM by removing the Neg. battery connection and it seemed to work for 4 days now my MPG has gone bad again. It seems to run smooth/good.
View 1 Replies
I've got an issue on my Escape, and I'm at a dead end. '01 XLT V6 150K miles.
About a week ago, driving to work, it started stuttering or misfiring while accelerating up inclines. Cruising and idle were smooth with no issues. I found that if I let off the gas as it was stuttering, it would stop, and then I'd give it gas again, and it would be fine. It was pretty intermittent.
Opened the hood and the large vacuum hose that goes from the top of the intake down to the PCV, has an L boot that connects it to the intake. That boot was collapsed down on itself while the motor was running. It went back to normal when I shut it down. I felt the boot and it was very thin and worn out, so I replace the whole two piece hose, along with the PCV valve. The old PCV came out and was rattling, so I believe it was ok, but I installed a new one anyway.
Drove it after that and it still had the stutter. It was now also doing it just barely at idle. I'd hear the motor miss, and it would really start when I would give it gas. I thought it was still a vacuum issue, and that there were probably other bad hoses. I found two. There's a small hard plastic line that comes off the air intake hose from a T, and those lines go to the camshaft covers. The hard lines go to rubber boots on the cover, and the one in the back was in two pieces. Replaced it. No change.
The other line is a small rubber line that comes off a round component, (I still haven't found out exactly what this part is called), that is bolted to the drivers side shock mount, and has a couple soft lines coming off of it. One of the lines goes over the top of the motor and ties into a T right where that large PCV hose goes into the intake. The part is circled in red, and the arrows point to the hose in the attached pic.
View 12 Replies
Had a misfire in cylinder 1 so I put new plugs and wires. Still misfired. Changed fuel injector. Still misfired. Changed ignition coil and misfire on cylinder 1 is gone now cylinder 2 and 3 are misfiring. I double checked wires and they are properly installed.
View 11 Replies
OK so this issue first started in July on way back from Florida the brakes started going to the floor. You did have normal braking power, but you had to about stand on them. Took it to mechanic who cleaned and adjusted brakes, after that they seemed to work fine. Fast forward to a month later, I was going over some train tracks with a somewhat heavy load, I braked when going over them, right after that it seemed the brakes went about half way before braking. I took it back to same mechanic who said it's now either the Master Cylinder, or ABS module. I have found so many conflicting posts on this I'm not sure which way to go. I'd really hate to spend $400 on MC, and then it turns out to be ABS. There is also a swooshing noise when you depress brake.
View 11 Replies
I had to replace all brakes because the bleeders were rusted in, wouldn't come out. So I bled and re-bled, but the brake pedal is still squashy and goes down too far if I have to stop from any speed. I even used my vacuum pump for evacuating air conditioning systems, pulled quarts of fluid through all the brakes-definitely no 2004 vintage fluid in there any more! Yes, I made sure to never pull the master cylinder reservoir empty, which would let in air. I always start from right aft and end up at left front, in order of bleed first. No leaks, the fluid level is always where I left it on previous session. I must be missing something...How can there still be air?
View 14 Replies
Im wanting to delete my abs brake system in my f150 2002 2wd all disc brakes.
I have to change the module with some kinda valve? and turn off the Abs in a tune?
I know the basics of a brake system, but im lost in the abs stuff.
View 6 Replies
This is on my 2002 Ford Excursion 4x4. I have replaced the brakes 2 times with the same results.
New: rotors, pads, calipers and grease the caliper slide pins so they are sliding properly. I have also replaced the slide pins the first time. I even lightly greased the ends of the brake pad back plates where they mount in the calipers/brake clips. There is always more brake dust on the left front wheel compared to the right front. The steering wheel turns to the left when I hit the brakes. I can't figure this out.
The one thing that seems strange is it was very difficult to get the pads and brake pad clips into the caliper. It almost seems like the pads are too tight into the clips/caliper. I am wondering if taking a little material off the ends of the brake pad back plate to allow better movement in the caliper/clips.
The left front is either grabbing too much or the right front is not grabbing enough.
View 14 Replies
I just recently purchased a used taurus and was experiencing rough idling and misfiring during operation. I replaced the EGR valve, the egr sensor, coil pack, spark plugs, iac valve, as well as check for vacuum leaks near all the hoses. I am a novice when it comes to this, but I was able to change those without issue. The misfiring was fixed during driving, but I still have rough idling. The needle seems to stay in check pretty well and the check engine light isn't on, but the car kinda hesitates and it causes the car to rock when idling. You can also feel the stuttering and rocking when cruising at very low speeds (5-15mph). I've already plugged in a decent amount of money into parts and am running out of patience when it comes to fixing what is a "potential" problem, and it winds up not fixing much.
View 5 Replies
My ranger just started running very rough. Like misfiring, but I think it may be the fuel pump. It starts and drives...but it surges then drives normal, as if fuel is being fed, then starved, then force fed etc. My father asked if I had trouble starting it and to be honest in the last 6 months it was a little harder to start on several occasions. On a few occasions it required more cranking. But that was only a few times.
I tried putting in a fuel injector cleaner and 93 octane gas but it is still running even rougher now. I changed out the fuel filter under the rail about a year ago (maybe 8000 miles ago at most). My father thinks the fuel pump is shot and he laughed because his went on his expedition and he said it is inside the fuel tank and there is no way to get at it without dropping the tank. Is that true? 2002 ranger xl 4cyl
View 7 Replies
I recently picked up a 2wd 2002 F-150 with a 4.2l V6 that has just over 300k miles. The CEL is on and I'm getting P1131, P1151, P0316, P0305 and an occasional P0301. It has a very distinct misfire from around 1,000 rpm and smooths out between 1,500 & 2,000 rpm, the idle rpm occasionally bounces (sometimes enough to stall), and the idle is sometimes rough.
I have replaced the plugs, wires, fuelfilter, and replaced a leaking PCV hose. As I have changed things the symptoms have improved some but they are still there. While capturing some livedata it kept going out of CL and into OL Fault. When it would the idle quality was crap and the miss was much more significant. I would have to put it into D hold the brake and run the RPM's up to just over 1k to get it back into CL.
After I got done with the data stream at idle, I set the parking brake held the foot brake and put the truck in D then ran the rpm's up to around 1,200 & held it there. The truck stayed in CL but it would cycle between misfiring for 5 - 10 seconds then clear up and run smooth for 20 ' 30 seconds, every time it cycled there was an audible click that could be heard. Also, the AC was off the whole time.
Live DataStream @ Idle: CL
CalculatedLoad Value - 12.9- 14.1%
EngineCoolant Temp - 103degrees C
Short TermFuel Trim B1 - 32.8%
Long TermFuel Trim B1 - 0.0%
Short TermFuel Trim B2 - 32.8%
Long TermFuel Trim B2 - 0.0%
Engine RPM - 816 . 846
[Code] .....
View 14 Replies
I own a 2008 Ford Escape Hybrid and when I step on the brakes (how hard I apply the breaks it does not matter - it always happens at low speeds) it makes a loud noise as if the disk brake is not well secured on its mount and the breaking action is forcefully shaking it off its mount.
View 2 Replies
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 Replies
I have a 2003 Ford Escape 3.0l V-6. In June while driving to a job interview, my brakes unexpectedly failed. With absolutely no warning, the pedal went straight to the floor. I replaced the master cylinder...problem solved. 5 months later, driving to the gym, after stopping successfully several times with no mushiness in the pedal, at an intersection, the pedal goes straight to the floor...no stopping power.
I can't remember if the brake light came on last time. This time it did. Both times the fluid in the reservoir was full and looked to be relatively clean. Both times there were no apparent leaks in any of the fuel lines, abs module, at the cylinder, etc. I'm no slouch when it comes to car repair. The master cylinder replacement was done correctly, the lines were bled properly.
I have my own theories but I don't like any of them as my car rolls properly at idle, my brakes have not, nor do they currently make any noise or grinding sounds, and the pedal goes all the way to the floor.
View 8 Replies
I have a 02 ex 118,000 on it, not a every day driver, mostly weekend and camper towing. The truck was running great, stopped at a light and the engine started hesitating, the od light was flashing, and then it died.. started right back up no od light, but was still hesitating/missing took it to a local shop, they hooked up a scanner and said that several coils were misfiring. My question, replace all coils? go with oem coils, or aftermakert?
View 6 Replies
The driver side brake light does not come on when you apply the breaks but the light comes on when you turn them on.
View 2 Replies
2002 f150 4.6l v8... Truck is misfiring and the exhaust is smelling very rich, I have new coils and plugs, it also idles rough and stalls if i let it idle for more than a couple minutes. Could it be something with fuel delivery system?
View 1 Replies
So basically I thought it would be a great idea to degrease my motor from the top down.... After washing I start it up and drive down the road to head abunch of misfiring under heavy load or high rpm's.
My problem is that the misfiring won't throw a code. I then proceeded to buy a new ignition coil (thinking this was the problem) but with no code to go off which cylinder was bad I just switched the good ignition coil into each cylinder and starting it.
Up each time. None of them seemed to make it better. Also the injectors all seemed to be good. So what to do ?
2002 Ford F-250 5.4l
View 3 Replies
Where is DRL (Daytime Running Lights) module located on a 2002 ford escape .....
View 1 Replies
I will try to make this short but still involve all necessary information. I was driving on the highway last Wednesday when my cruise control went out and i couldnt drive over 25-30 mph, my check engine light did not come on when this happened. I managed to limp the car very slowly about 2 miles down the highway as that was the nearest exit. I took the exit and when i went to "accelerate" at the light i got a loud whooshing sound from under the hood. I pulled into an auto repair shop and found the EGR Valve had a hole blown in side.
Several hundred dollars and several hours later the shop put on a new EGR Valve and had cut the lower cat converter of the car and run a straight pipe where it had been. They said they believed the cat got clogged and built up enough pressure to blow the side out of the EGR. The car ran fine like this for a few days while i waited on my brother in law to gut the cat so we could replace the cat shell as to be within the law, as it is illegal where i live to remove the cat. We gutted the cat and cut out the section it was originally and put the shell back on. The car ran ok for a few hours but then i stopped at a gas station and the check engine light started to blink and the rpms would run way low. When i say low i mean around 1000 at 55mph and would idle around 250, if i put the car in neutral it would idle around 500 but that is still low. What i could look into as the cause of this issue?
View 15 Replies
For a while now, my 2002 Ford Escape has been making a creaking noise. It started with the steering, or so I thought for a while. I checked the power steering fluid and it wasn't really low. Nevertheless, at one point, when there was a little bit of room, I added a bit of fluid with "stop squeaking juice" in it. That only barely worked.
As time went on, though, the whole car began to creak. If I were to make the sound outloud, it would remind me of a hee-hawing mule or someone bouncing on old bed springs. This has continued to get worse -- and seems at its worst when it is very cold. It happens when I go over speed bumps (yes, even slowly!) or turn in any direction or just go around sharp turns in parking lots, etc.
I am guessing that the original sound in the steering is separate from the other sound and it is just coincidental that the two sounds have been happening at the same time. I also don't know if this info has any bearing, but lately when I'm idling, I'm smelling a burned oil smell, but my oil is not low and I've noticed no leaks. My gas pedal is sticking badly (I have to jam it down sometimes to get the car to move forward) but I've had that happen on and off over the years and have just gotten the throttle body cleaned. I've put it off a little longer than normal this time, which I think is why it is so resistant now. But I suspect it has nothing to do with the creaking. Does it?? Or could the probelm maybe be the shocks? That occurred to me today.
View 6 Replies
