Ford Escape / Hybrid :: 2002 3.0L 4wd - Thumping Noise / Severe Shaking When Accelerate
Jan 1, 2016
My brother has an 02 ford escape that he bought cheap because it needed a transmission. He just replaced the transmission in it as well as tie rod ends, front axles, axle bushings and seals. The front pads and rotors are new and the tires were just rotated. Now when you are going 15mph and up and are on the accelerator there is a severe shaking as you accelerate and a loud thumping noise. If you let off the accelerator it goes away. If you get it going fast enough it will shake so bad the mirrors will shake. He is a ford mechanic but said he is having a hard time pin pointing what it could be . He took me for a ride. He said he has had other mechanics look at it but they can't figure it out.
View 5 Replies
Advertisement
I am having a lot of issues with my 2002 ford escape, a while if I drive the truck acts normal, but after driving it starts missing when beginning to accelerate at a dead stop check engine light starts flashing pulled codes coming up with #4 cylinder misfire and #5 cylinder misfire detected, also a catalyst system below threshold bank 2, I have had the vacuum lines repaired and still no changes and went through and changed my grade of fuel from regular unleaded fuel to premium fuel, actually went worse with using premium fuel. I was thinking of replacing all three coil on the front of the motor, putting new plugs in it and seeing what that does.
View 2 Replies
I have a 2002 explorer 2wd. I am trying to find an answer for this thumping noise as I accelerate. My first thought was a tire. I took them to be checked and had one replaced but all are good and less than 5k miles on them. I feel it in the pedals and in the steering wheel. The repetitive sound increasing with speed. I have, in the last 2 weeks, changed front rotors and pads with no difference in sound but good brakes now. And today replaced the drivers side upper ball joint and the front ds wheel hub assy. And no difference. What may be the problem?
View 1 Replies
I was out driving tonight and our 03 escape started making a thumping sound like you hear when you have a flat. I turned the corner and noticed that the steering wheel is now at a 30 degree angle as I'm going straight and when I hit the brakes the steering wheel straightens out but the car doesn't change direction. It's dark so I can only see so much but the tie rods are good and tight from what I can tell same with ball joints. They just did that subframe recall a month or so ago. My concern is steering box but other than these symptoms it seems to be working fine.
View 4 Replies
Wondering what could be possible causes of severe shaking while under acceleration?? Also does it worse when turning right. Will just vibrate and start going wherever.
View 2 Replies
Fitted new snow tires with the intent of leaving them on year round. Now find that the Escape is pretty well un drivable due to shake at all speeds. Balance has been checked by two tire shops. I think that the problem is that the deep blocks of tread are "squirming"The tires are surprisingly quiet but unfortunately will have to go.
View 2 Replies
I have a 1996 Dodge Ram 1500 5.9L V8 4x4 ... Automatic transmission sport model
I have a severe shaking at 1500 rpm last gear and a slight shaking at idle doesn't shake when I'm off the gas barely shake when I kick it into higher revs but I than hear piston slap.
I replaced the spark plugs and I have brand new U-joints. Last night I checked all the plug wires and they are all getting spark. But my exhaust is skipping like I'm not firing in a couple cylinders
I checked the rear transmission mount (I'm replacing it). And the Engine mounts look ok but I'll check again today
I've read a ton of forums and they all have different answers so I'm really trying to figure out what is wrong before I spend a bunch of money replacing things that won't fix it!
I've read that it can be my tranny, TC, Harmonic Balancer, Steering Stabilizer, pinions, Tie rods, Steering(over all), IAC, Fuel System, IgnitionSystem.
View 1 Replies
2002 3.0L escape 4WD, stalled twice on me when shifting into reverse after a complete stop. No CEL, truck started right up again....
View 4 Replies
I have a failure on the evap system of my 2002 Escape, and need the proper testing procedure for this particular purge valve. I was able to fix the purge valve on my 2013 Explorer, with no issue, but the Escape has a different type and I'm not sure I'm testing it properly. I want to verify the purge valve is working properly instead of just throwing parts into it. I know it is likely either the valve or the gas cap, but it could be something other than those two items, so I want to get the simple stuff checked out first.
View 3 Replies
I am having some ( Bad Luck ) with my 02 escape I been getting random misfire codes started checking over o2 sensors first, replaced one on bank 1 downstream, I have screenshots to look over along with codes....
View 3 Replies
I own a 2002 Escape, 4WD 4cly manual trans. A couple of days ago, when I left work I stopped at a stop light. I shifted out of gear while I waited for the light to change like I always do. When I went to shift back into gear, I couldn't. I found that if I turned the key off, with the clutch disengaged, I could shift into gear without a problem, start the car up and drive away.
Since the first time this has happened, it has happened a few more times, always when stopped, once or twice while slowing down to stop (low RPMs). Besides all that, the car shifts fine while driving.
View 1 Replies
I have a 2002 Ford Escape, 6cyl FWD... 110,000 miles.
About a month ago I started seeing a misfire, which of course usually is a COP issue. I should buy stock in whoever makes those. Anyway, the code according to parts store monkey was cylinder 2 misfire, so I replaced the COP. That made no difference. I also replaced the upper intake gaskets and the PCV valve while I was in there.
So I started monitoring when it would happen, and of course got the actual code rather than taking the word of the monkey at the parts store. The code is P0352 Primary / Secondary circuit malfunction.
So after some research I find it could be the harness, it could be the PCM. The question I have is this misfire seems to only be when the motor is started after it's hot. What I mean is I can drive to work 10 miles, no problem. I can drive to Orlando 100 miles away - no problem as long as I don't stop on the way. The only time the misfire happens is when I start the motor when it's hot. So if I drive 10 miles to the store, then drive home before the motor cools completely I'll be coming home on 5 cylinders. If I wait 2 hours between stop and start I never have a misfire.
Does that jive with a true electrical problem? I'm no expert, but I don't understand why driving for 100 miles is fine, but 10 miles, stop start and 10 more is an electrical problem.
View 14 Replies
Are there any tricks I need to be aware of, or any maintenance threads on changing the lower intake gaskets on my 2002 3.0 V6 Escape? Still having high idle issues when hot, and have checked everything else. I changed the upper gaskets when I replaced the plugs and COPs some time back.
Anything I need to be aware of, or is this similar to changing the upper manifold gaskets?
View 8 Replies
I have a 2002 Escape XLT V6 4X4. I searched the issue, but others' symptoms don't seem to be quite the same as what I'm seeing. Over the last few weeks, the battery light has randomly come on and off 3 separate times:
- 1st time, light came on at highway speed for about 30 sec and went out. Didn't come back on. Was during daytime, running DRL's, radio (no amp or subs or anything like that, and heater blower on low speed.
- 2nd time was two weeks later or so. Happened at night with just headlights on at around 55mph (RPMs about 2K or so). Again, stayed on for about 30 sec and went out.
- 3rd time was about a week/week and a half later, yesterday morning. Just running DRL's and radio. Light came on, flickered, came on, and then stayed on for a couple of minutes (all at highway speed). I noticed that if I disengaged the overdrive and got the RPMs up, the light would go out. I ran it out of overdrive for about 2 minutes like that, and the light stayed out. Speed limit dropped to 40mph, and the light came back on (lower RPMs at that speed, didn't run it in low gears). Light stayed on for 30 sec - 1 minute, and then went out on its own and has since stayed off.
I took it to Advance yesterday to have it tested, and the results were that it is charging at 13.9V under no load, and 13.87V under a load. The battery tested good, but the machine said it needed to be charged (it hasn't been acting low...car starts just fine).
I'm driving it to work today to see what it does next, and then getting it tested again on my way home. Has anyone here ever had similar symptoms as above? Does this sound like bad diodes in the alternator?
View 5 Replies
My wife has a 02 Ford Escape XLS with a I4/manual trans, she has been saying it has been making weird grinding noises for a while but has not been able to replicate it for me to hear. Today it locked in gear and stalled, she can depress the clutch and start it, but can't take off in whatever "gear it thinks it's in" and it'll stall. To quote her.
So odds are the clutch or trans is toast, I'm more of a full size truck guy when it comes to doing work, what to look at? She's getting it towed and I have enough tools to do the job just not a ton of time this second to do the research, When I know more I'll add it.
View 4 Replies
So my buddy has a 2001 escape. It has a shudder at 1k rpm in park and neutral. It's not nearly as noticeable in drive. I scanned it for codes and there isn't one. Ran a power balance on ids and it's straight. Doesn't miss during the shudder either. Has all new coils and plugs. I cleaned IAC. MAF. Ran sea foam through the engine. And there is Lucas oil conditioner in the oil and Lucan fuel injector cleaner in the gas. It runs amazing other than that shudder. What could it be ?
View 1 Replies
2002 Escape XLS 2.0L 4-cyl 5MT FWD. Slipping Clutch.
I've read here n there that the Escape clutch is a poor design & others have reported that a clutch repair doesn't solve their shuddering problem. After putting off the job for a while, I'd like to replace the clutch.
Here's a topic from here : Manual Transmission shudder / fill & drain access?
View 2 Replies
My daughter has a 2002 Escape 4WD with 3.0L engine.
Coming home from school a few weeks ago she experienced engine running rough on the highway when trying to accelerate. We ran the diagnostic on it and it revealed that #2 cyl coil was misfiring.
I've replaced all of the rear bank coils (in hopes that I wouldn't have to remove the intake manifold again anytime soon). I also replaced the connectors and weatherproofed them.
Replaced all the plugs while I had easy access too. This all went pretty smooth with exception of breaking 3 of the 5mm coil bolts off inside the valve cover. I've also replaced the upper and lower intake manifold gaskets.
It runs much better now except now on the highway, at 1800 rpm/55 mph if I try a gradual acceleration I get engine sputtering and it won't accelerate. If I push hard on the pedal it will downshift and accelerate normally right past this trouble spot. Other than this it idles and runs great.
I've noticed that the 3/4 in. vac hose on back of manifold is getting pinched closed about 70%. this is the hose that leads down to the top of engine just below lower manifold. I suspect this is the problem but cannot determine the root cause. I assumed it was the intake manifold gaskets but those are now replaced.
View 1 Replies
I was having problems with my 02 Escape of misfire on cylinders. After doing a lot of checking, changing spark plugs, changing coils, ect, I decided that it could be the computer. So, I ordered one and put it in. When I turned on the key, all the gauges pegged and then came back to zero, but it acted like someone cut the power line to the starter. No click, no nothing. I checked fuses and they are fine. Even changed them around to make sure. Is there something that I have to do when you change the computer to get it to start? Had no problems with the starter prior, so it has to be something associated with the computer and changing it.
View 3 Replies
I set out to do a coolant flush but ran into an increasing number of problems. When I went to replace the thermostat I discovered one of the three bolts would not come out due to the inside thread on the thermostat housing being stripped. I purchased a brand new housing and O-ring.
When I reinstalled the thermostat (also Motorcraft brand) with the above O-ring and attached all the hoses I had a severe leak between the thermostat housing and the intake hose connecter. I diagnosed the problem as the O-ring slipping off of the lip or ledge inside the thermostat housing and not sealing all the way around.
The Motorcraft O-ring seemed like the diameter was too big for the interior lip of the thermostat housing because the ring would pop up on one side whenever I tried to fully seat it on the interior lip. I went to AutoZone and purchased an orange Duralast O-ring, and while it seemed to be a little smaller diameter than the Motorcraft it too slipped off when I tightened down the housing.
I have tried everything, and every time I tightened down the housing I did it very slowly and carefully doing an 1/4 turn at a time with the three bolts but still the O-ring would slip off.
View 4 Replies
I'm getting a p0452 fault on my 2002 Escape 3.0 V6 2WD. From what I've read, that seems to indicate low FTP signal below .22v. As I understand it, the FTP sensor has 5 v applied, and the output to the ECU goes down as tank static pressure increases. Conversely, I think the voltage back to the ECU goes up as tank static pressure decreases (for the vacuum leak test measurement).
What the approximate voltage is at atmosphere (engine not running, vent valve open, etc)?
I'm guessing the "less than .22v minimum" signal back to the ECU might look more like either the signal wire shorted to the frame somewhere or the signal wire open (maybe corrosion in the connector)....
Also, where the FTP sensor is located on the Escape and how to access it?
View 3 Replies
