Ford Excursion :: No Reading At Oil Gauge And Temp Light Is On When Very Cold
Jan 24, 2014
I have a 2001 Excursion Limited V10. 146000 miles 2 wheel drive. I have had it about a year and this is my first winter to really have experience with her.
When the outside temperature is very cold and the engine is cold from sitting all night, at start up, the oil pressure gauge reads nothing and the oil pressure/temp idiot light is on. Only does this during the first very cold start up or after sitting and engine getting very cold again.
I can drive just a short distance (2 blocks) and both gauge and light go to normal and stay there for the rest of my drive. I am using a quality 5/20 oil and filter and the level is good. Warmer days it has never happened. Truck runs fine, smooth idle, no "limp mode". She has not had any recent work done. All the other dash gauges read fine.
There is something about really cold temperatures that have to be causing the issue , I think. ??
View 5 Replies
Advertisement
I have a 2003 Excursion 6.0. I didn't post this in the 6.0 section because it may not be just a 6.0 issue. (See what I get) On cold starts, anything under 150 degree water temp reading on the SGII. I get a CHECK GAGE light on accompanied by the check engine light. No codes read on the SGII pending or stored. Just some of the time I get a water in fuel light too. This tends to go out fairly soon after driving. (Even after I just drain the fuel pump it still happens.) other issues that accompany the lights are as follows.
The trans temp does not give a reading to the dash. The oil temp does not give a reading the dash. Both show proper temp on the SGII. When in reverse the back up alarm beeps as if something is behind me. And the auto door locks will not activate after 10 mph. The tach also will not show a reading in the dash. SGII shows the numbers. Now the kicker, this ALL gets resolved the instant the water temp hits 150 degrees. The only lingering issue is the that the tach will surge or drop every now and then. The tow/haul light does not come on when this is going on. I've checked the battery terminals all are clean. Both batteries are brand new.
View 9 Replies
I have been having an intermittent (2 times in the past 2000 miles) oil pressure gauge not reading. As I own a 6.0L I understand that this is just a pressure switch in reality and if the engine was starved of oil the HPOP system would kill the engine. The first time the oil gauge went out it was raining out. The second time was after going through a carwash and getting the underbody wash. At this time my battery light also came on for a few seconds.
Both problems seemed to go away after an engine restart. Today it is snowing lightly and my battery light came on again. I happened to be monitoring the battery voltage and FICM voltage via OBD II using Torque app. At no time while the battery light was on today did the battery voltage drop below 13.5V. The FICM was also stable at 48.5+/-.5V.
As the battery voltage read by the PCM is not actually dropping and the previous oil pressure gauge and the fact that my left blinker indicator is out I am thinking I may have electrical issues with the gauge cluster. I have never had these issues while driving in dry weather. Where do I start troubleshooting this? Also I am going out of town for the next two weeks and my girlfriend was going to use the vehicle. Is it OK for her to drive?
View 1 Replies
It is a garage queen 1994 4.0 AWD with 42,000 miles in nearly perfect shape. Except for the dent in the rear on the passenger side.
I have posted a picture of the dash when going down the road. As you see the engine light is on. It comes on intermittently, pulled the codes, indicated MAF, 02 sensor, running lean/rich. Runs like a champ, no hesitation, still gets up and goes, gets the appropriate gas mileage. I replaced the 02 sensor with the original Ford Part. Didn't cause the engine light to stop going on after about 20 to 60 minutes driving, sometimes it doesn't come on at all.
Could this thermostat be running too cool and causing the engine to throw those codes? Would gladly take it to a mechanic, but seems like it might be a fishing trip with my dollars for them. Next I was going to replace the MAS myself, easily done with the original remanufactured part at a cost of 150.00, 70 for the core, but don't want to chase my tail with these engine lights on when it runs nearly perfect.
Have sprayed the MAF. Checked for air leaks anywhere. Done all the things I could do by just lifting the hood.
So the picture shows the Temp gauge barely touching the N flying down the road at 70 on a level surface, outside temp about 60. Reading the posts says they all run in the cool section of the temp gauge.
So the question is, do they run this cool? Heater works fine and the gauge goes up past the N resting before the O when going up hills on the way to Tahoe. Is this a thermostat problem on a 20 year vehicle with low mileage, or am I going to have to bite the bullet and let the mechanic go wandering through the vehicle?
View 14 Replies
I have a 77 F100 2wd 302/c4. I recently replaced the rear plate to my gauge cluster after it crumbled to pieces. I swapped all the gauges to the new plate minus the fuel gauge since it decided it couldn't live if livin was without the old plate. I have a gauge cluster out of my 75 and decided to swap in my fuel gauge from that one. I put the cluster in the truck and fire it up for 10 mins or so and everything is working great except the temp gauge isn't moving. I figure it romeo and Juliet with the fuel gauge so I just swap all gauges from the 75 into the 77 cluster except the speedo. Same result.
So I figure its the sending unit now and maybe both gauges were fine to begin with. I put in a new sending unit and now the gauges works but the needle sits on the P in the word TEMP on the gauge which makes me uncomfortable. That's about 1/4 inch or so from being past the end of the gauge. I don't believe the truck is running that hot. The gauge was more or less straight vertical before the swap sitting right at the end of the E on TEMP. Did I get a bad sending unit? Is it a bad ground on the gauge? Was I supposed to take off the teflon tape that came on the threads of the sending unit? I'm gonna try removing that first and see if it lowers the needle.
View 3 Replies
My outside temperature reading on my '05 (6.0 PSD EB) Ex has recently gone black..no reading. I haven't noticed any other issues, just no outside temp readings... Do these sensors go bad or ? Is it a big deal to change them out?
I was told it should be located just to the side of left hand (drivers side) headlight behind the grill, a small black cube (approx. 1 inch square) with three wires coming out of it. However, I'm not finding it there.
Where is the temp sensor located? Is there a fuse covering this sensor?
View 11 Replies
02 6.8 4x4 excursion. When I start the truck cold, the trans temp gauge immediately moves to "running" temp. Not really sure how this happens, I'd figure that if the xducer was trash it would ride all the way high or all the way low. What's happening here? I'd sure like a functional gauge...
View 6 Replies
I have a 2005 Toyota Matrix with 250k on it. It has run like a champ so far, with the only problem being an ECM recall last year. I have noticed a few problems recently; the heat blows cold air for quite awhile, and the temperature gauge, while not reading hot, sort of fluctuates between normal and a little warm. When the ECM was being replaced, the dealer said the serpentine belt was overdue for replacement, and I know he's probably right about that. He also said the water pump needed replacing, although I have never seen any signs of leaking. This car has been a champ, and I'd like to try and get another 100k out of it if possible. I'm pretty handy around a car, I've replaced an alternator and radiator before, and I'm working on a limited budget, so if any of this is doable by me, I'm up for it.
View 11 Replies
I was recently given my first Volvo. Its an 88 240dl. While driving my temp gauge climbs up to the red and sometimes hovers inside of it. It normally climbs up at stop signs and comes down on straight always then climbs right back up close to red. When the gauge was in the red i stopped the car and popped the hood open to see that the engine was not actually overly hot.
first i replaced coolant. nothing
then i replaced the thermostat. nothing
flushed radiator. nothing
Today i finally had enough and decided to switch out the water pump with a new one hoping that it would solve the problem seeing as it still had the factory one on. It did nothing. the gauge continues to climb up. I did replace one of the two senders in hope that it would fix the gauge reading but nothing.
View 4 Replies
Every now and then when I slow down the temp gauge drops about 1 notch below its normal 200 reading. It's nerver done this before. Car runs great and heat is strong. Is this a sign of a failing thermostat? If so, where is the thermostat located, is it hard to replace, and should I get OEM or is OTC ok? Car has 89K on it.
View 11 Replies
These are my gauge readings at 70 degrees Fahrenheit. According to an AC conversion for gauges calibrated in Pascals, 35-40F converts to 241-276 KPa, 140-160F converts to 1000-1103Kpa. The gauges are in Mpa which by conversion is 3 decimal points to the left so .241-.276 and 1-1.103 Mpa. Here are my gauge readings at 68 degrees ambient temp. Rear air is same as an ambient temp on max ac and the front is pictured. There seem to be virtually no pressure differences which I would interpret as a novice that there is ) freon flow.
There is freon in the system with the high pressure being approx correct but the low side is too high if I understand correctly. Basically when at highway speeds at 75 degrees yesterday the front AC was cold and the rear was outside vent temp only. There are slight leaks in the low and high-pressure valves. I have a Mastercool replacement tool but they did not send a fitting for the high-pressure valve. What these readings mean as far as what may be wrong?
View 14 Replies
I have a 98 trans sport and the temp gauge is reading low. Only on the first line when driving then when i pulled into the garage it went up one line and heat got warmer. Felt both upper and lower hoses and i can press them both in Fluids are full no leaks anywhere. oil is good tranny fluid is good. I just got it on a trade it runs and drives great no problems at all.
View 6 Replies
I have a 2006 Jeep Liberty 3.7L that has a temperature gauge on the dash that reads an overheat when driving. The oil looks normal, there is no white smoke, no bubbling from reservoir. I have replaced the following:
Radiator
Thermostat
Water Pump
Coolant Temperature Sensor
Coolant Reservoir Tank
I am not leaking any coolant and the reservoir level has been fine. I have let the vehicle idle for 20+minutes, with no overheat. When I drive it around, the temperature gauge will read an overheat. When I stop the car and pop the hood, the engine is not overheated and both rubber hoses to/from radiator are flowing the coolant. The only thing that will bring the gauge down is turning on the heater full blast. Could this be the gauge itself being bad? Could it be a short in a wire somewhere? I had thought maybe a head gasket, but have no symptoms of a head gasket.
View 9 Replies
I have a 93 accord ex sedan, 4 cylinder, automatic that I bought in August. I live in South Dakota & it's starting to get cold here. When I first bought the car the temp gauge was working fine in that it would move to the middle of hot/cold range. Recently, I've noticed the interior doesn't get warm for awhile, even after driving 20 miles. It blows warm air but it seems like it should be warmer. I've also noticed the temperature gauge barely moves, if it does at all. Most of the time it doesn't move or just stays on cold. I did some research on here & thought I would try to change the thermostat, upper & lower hose and the antifreeze. I'm hoping this will heat up the interior better because it's starting to get cold here & fix the temp gauge.
Previously, I had a 91 accord & that would warm up great, even when it was bitterly cold here. What would cause the temp gauge to do this? I'm even thinking about changing the transmission control module because I read on here that could cause the gauges to have wrong readings. The speedo & rpm gauges also seem to have wrong readings, especially in the mornings or when I first drive it. I used my gps & found the speedo to be off by as much as 10 mph. The other item I've noticed is that I only get around 23-25 mpg highway & on my other accord I was averaging 28-30 mpg highway. Not sure if this is related or not but thought the more info the better.
I have done all the basic maintenance-oil & filter, plugs & wires, valve cover gasket, air filter, tranny fluid but have never done anything with the heating/cooling system.
View 3 Replies
Tempature gauge on my 2001 sierra (4.8) has been running low for awhile. The highest it will reach is round 160. It's currently running rough/rich and bad mpg. I replaced the ECT sensor but didn't work. I'm not sure if there are two ECT sensors on this model. I don't think it's the cluster. Is there a second sensor I'm overlooking?
View 13 Replies
I recently replaced my alternator. I thought I was very careful not to make anything worse but now when I'm driving I have temperature issues. When stopping or slowing down my temp. gauge goes all the way to cold, then as I accelerate the temp gauge rises to the middle. It has not gone past the middle and has never done this before the repair. Also, the truck has never overheated or had any thermostat or cooling issues before.
View 6 Replies
Today was drive my x 2000 v10 limited 4x4 114k miles). It was 90 degrees Out and was driving in light traffic going 40 and noticed my temp gauge almost up to h then dropped fast. So shut the ac off and it continue to rise and drop fast I went few more miles to where I was going checked everything could see no problems it sat for about 30mins then left on my drive back home 36 miles and had ac on and no problems stayed where it normally is. I am thinking of just replacing the belt cause I never have. No weeping from water pump. Or any smell.
View 6 Replies
I have a 95 ford f350 when u run it with the heat on the truck temp gauge says its overheating the heat will go from nice and hot to ice cold as soon as the temp gauge goes up to the red. I replaced the thermostat also checked for coolant leak cant find any but truck has strong anti freeze smell and the radiator keeps going low on coolant.
View 2 Replies
'05 Ex overhead console temp is showing -40 deg... Had the board out looking for loose diodes, didn't see any. Have any of you ran into this before?
View 14 Replies
So a couple weeks back I'm on expressway home and I look down and and temp gauge is pegged out overheating I immediately pulled off and shut it down and towed to a buddy of mine's shop he flushed it filled it up w antifreeze and checked for leaks and couldn't find one. I drove it for about a week and got out to for a quick stop , Ex parked on a slight decline and came out to prolly half gallon of coolant on the ground..I limped it to my buddies shop as it was not running hot .. he has checked it out but can't find any leaks, even after having it run 30 or so minutes..
View 6 Replies
I am going to install an aftermarket gauge on my Excursion. Just would like to know the best place to install the probe. Hopefully it isn't that hard.
View 14 Replies
