Ford Excursion :: Turn Signals Stop Working With Brakes Applied
Apr 17, 2009
Just noticed this tonight. While making a left turn, I had the blinker on and had the brakes applied and noticed the indicator on the instrument cluster was blinking. Once off the brakes, it took it a few seconds for it to resume blinking.
When I got home, I checked to see if the right signal did the same and it did. I also checked the rear lights and when the signal is on and the brakes are applied the light does not blink nor does it brighten up like they're supposed to when the brakes are applied, it stays dim as if both the blinker and brakes are off.
I did a quick search. I have not checked any of the bulbs or wiring, but I'm thinking it might be the turn signal switch/ lever. What the problem might be?
View 14 Replies
Advertisement
Well, on our way home during my leave, the wife made the comment about halfway home that the blinkers had quit working. I assumed it was probably a fuse or relay, so we came on home. I have been looking at it for a few days now (too hot to spend too much time out crawling around under the dash ) and I am still having some trouble. My brake lights, and hazards are not working, and neither is the cruise, which was working fine while I drove before the blinkers went out.
I have no power at all to the flasher relay. I replaced the brake light switch because it was definitely worn and looked a little burned inside when I pulled it out and inspected, but still nothing. Have not found any fuses blown. Brake pressure switch fused link harness seems good with my test light. Wipers, brights, everything else on the turn signal switch works fine. Can't even get the cruise to go into diagnostic mode, it only blinks once when I try.
View 5 Replies
I have a 2001 Econoline and the turn signals work in the morning but when the vehicle warms up they stop working. I have replaced the bulbs and the fuses. What I could try next.
View 4 Replies
So on our trip up here I experienced a strange problem. Normally when I apply my brakes my trailer brakes kick in via the controller. This time when I apply the brakes I'm only getting my truck brakes. I can still use the brake controller manually to slow down but it's worrying. What is going on.
View 7 Replies
Well now I have to replace the multi function switch due to moving my steering wheel and the headlights sometimes working and turning signals not working. I saw a great video on youtube about changing a Multi Function Switch and it shows where the air bag needs to be removed. I was hoping that since my truck is an older 1997 F250 LD I wouldn't have to remove the airbag. Is there a way to do this w/out messing with the airbag on the 1997?
View 1 Replies
I have a 2007 Chevy HHR. A couple of weeks ago I had to change the caliper on the driver's side of the car. I had some squeaking after, but bled the brakes and the squeaking went away. The other day I took the caliper off and painted it. I have custom wheels and you can see the caliper plainly, it was rusted so I painted it. Now I am getting the squeaking again, but it stops when I apply the brakes. I bled them again, but still the squeaking. This is driving me crazy. Could it be the "chirper" that is dragging on the rotor? Also I want to add, it squeaks until I get up to about 45 mph. Then it stops. And as I said, it stops when I apply the brakes.
View 6 Replies
Just had a couple questions, The first one is in regards to the brakes on my '09. I've read that the brakes themselves don't actually kick in until you are going 7 mph or less. Anyways, when I am coming to a stop it is not necessarily smooth. I try my best to apply even pressure to the brake, but I basically come to a jerky stop. Is this common in a Prius? I bought my car certified pre-owned last month and I know the brakes were one of the checklist items.
View 2 Replies
Buddy has a problem on his '03 F-450 cab and chassis. When he turns on a turn signal, everything is OK...but it goes out when he applies the brakes. Also, the brake failure light is lit up on the dash, despite the brakes being fine. These problems happened at the same time. I'm think a ground, but not sure where to look.
View 5 Replies
I'm looking to replace the headlights and turn signals on my 2002 Excursion - I've seen loads on Ebay, but don't really know how to tell what ones are ok? I like the chrome style, and like the led lights too - but mainly I just want the front of the truck to look more modern (I am buying the 05 style grill too)...
View 10 Replies
Hooked up to my trailer and I have running lights but no turn signals, brake lights, or trailer brakes. I pulled plugged in my other vehicle to the trailer and everything works fine. My truck is a 2011 with the factory trailer brake control and pigtail connection. It worked fine last year.
I checked the connector with a test light and there is only power to the running lights. I then disconnected the plug at the back of the trailer connector and tested there and got the same results. Are there particular fuses or relays I should look at?
View 4 Replies
I noticed yesterday a sound, like a grinding sound, *sometimes* as I apply the brakes to stop. I'm at 68k. The noise only happens when the brakes are applied so I suspect there is an issue with my brakes again.
Some BACKGROUND info: At around 60k (or 8 months ago roughly), the front pads were replaced after the brakes were squealing and a pulsating brake pedal when stopping. The pads were replaced by a dealer. In addition, both front/rear rotors were turned at the same time. Rear pads had 40% at the time and were not replaced.
Some weeks later the pulsation came back and I went back again and they machined them again. For this current issue I was thinking about taking the car to someplace local (not a dealer) and getting a free brake evaluation of what is going on.
I'm also concerned that all this machining the dealer did to eliminate the pulsation may have decreased the life of the rotors and perhaps they need replacement now.
View 3 Replies
Coming back from a trip I got a e-brake light show up on the dash then noticed the signals stopped working and the heated seats no longer turn on. I scanned it with my AE and got a brake fluid sensor error come up but nothing about the signals .... is this a common problem or is there a connection between all this? 2003 F350 6.0L .....
View 2 Replies
So originally I was told it was my front brakes going bad, which was the case. To address the issue, I replaced the rotors and pads awhile back and the noise disappeared for a bit. Fast forward a month or so ago and I hear an on-and-off squeaking noise when the brakes are applied. It does not happen every time. Usually when I ease onto the brakes to a slow stop.
Figuring it could be my pads going bad for whatever reason, I decided to check my brake pads and rotors again. No odd signs of damage on the rotors and by the looks of it there was still plenty of pad left. I then sprayed some brake clean assuming it could be dust but there wasn't much.
I have not touched the drums yet but I'm thinking it could possibly be the drums or a bad bearing? The car is a 2012 with 38k miles which is the reason I'm doubtful of it being a bad wheel bearing. What could it be?
View 7 Replies
I installed LED tail lights a few months ago, now all of a sudden the passenger side does not light for brakes or turn signals. The lights came with resistors that I put in when installing and the adhesive wore out and they were dangling in the truck frame. The wires connecting the resistors to the light were damaged. I taped the exposed wires and secured them a with a heavier tape, but taping did not work. I also tried switching the resistor packs with the driver side to see if it was them that have an open winding, but they are still operable.
I narrowed it down to wiring between the trailer hook up and passenger light assembly in the electrical circuit. I plugged an LED light bar into the trailer connection and the same problem occurred (running lights come on, but no turn signal or brake light). Where could there be a short? Or is this circuit fused somewhere that the running lights come on but a separate fused circuit triggers the higher voltage for LEDs.
View 9 Replies
Coming to a left turn signal I was anticipating it turning red on me, and I drove into the turn lane briskly 30mph and then applied brakes as I made a u-turn. It sounded like a cross between dragging the front air dam and metal on metal brake grinding as I made the turn. Stopped immediately and did not scrap the air dam and all front end components checked out, okay. Car is driving just fine now, has only done this once.
View 18 Replies
I have an 88 ranger with the 2.9l. The headlights work and the markers do to. The brights don't though. and also none of the turn signals work, the brake lights work though but i don't think the reverse do, I can't see them. Do the turn signals and brights share a fuse on there own? How to diagnose it or what it may be?
View 9 Replies
Why my 2010 Prius has 3 times now failed to stop when brakes were applied on a steep downhill in slight rain? Happened a year apart with no slick road and with tires both new and old. I pull up to a stop sign on a grade, apply brakes, the car slows, then there are metallic noises and the car glides 3-4 feet before stopping. I'm lucky no car or person was in front of me. Honestly not a skid at all. Service tells me I don't know about anti-lock brakes but I've driven with them on cars for many years with nothing like this.
View 2 Replies
Is there a way to make the parking lights (on the boot) to work with turn signals and brakes? I want the turn signal action to look like this : [URL] .....
BTW, I tried searching on this topic but I found nothing. I'm planning to buy this kit - [URL] .....
View 4 Replies
I drive a 98 Ford Contour Sport. When I was driving today, I signaled a left turn, and the signal began working erratically. This also happened with a right turn, and, since I deliver sandwiches, happened when I turned my hazards on. Throughout the day it got worse, and eventually stopped working. I'm willing to bet that it's a wiring issue since all of my fuses are fine.
View 5 Replies
I have a 2003 Excursion 7.3 2WD Limited and all of the sudden experienced a number of issues all at once.
1. Turn signals stopped flashing (hazards still flash)
2. Lost Rear back up sensors
3. Lost overhead trip computer
4. Lost Rear A/C - switch does nothing
5. Front A/C now only blows through the defroster vent
I've checked all the fuses and cant find any bad ones.
I replaced the multi-switch flasher and turn signals still dont work - only hazards.
View 11 Replies
I have checked all fuses, checked wires on top of steering column all checked out ok. Hazards work but when I press brake tail lights just blink with no brake light but the 3rd brake light works??? Signal switch maybe??
View 14 Replies
